Posted by UpNup | Jun 01, 2019 @ 09:05 PM | 475 Views
Making my own wheels has been an interesting project. Using layers of balsa and basswood ply has been a challenge, but theirs texture looked like tread. The last part was building a "receptacle" into which they can fit inside the wings between #4 and #6 rib.

I've made my own plans on this. And except for pinching my thumb and later my palm with linesman's pliers working the 1/8" wire, it was relatively painless and full of good sanding effort.

The wheels were rattle can spray painted with Testor’s flat black and I used clear flat matte spray lacquer on the finished wheels for protection and durability. The hubs were dry brushed with Testor’s silver enamel. They were affixed with Gorilla Glue 5-min. Epoxy.
Posted by RCvertt | Jun 01, 2019 @ 04:21 PM | 522 Views
The Apollo XI field has been around for about 60 years. New legislation signed by our president gives the FAA new power over RC flying they did not have before.

Affective May 24th 2019 the FAA suspended operations at the Apollo Field pending review of the local airspace and operating procedures.
Posted by marblekit | Jun 01, 2019 @ 03:06 PM | 495 Views
Posted by GroundControlRC | Jun 01, 2019 @ 01:23 PM | 498 Views
Test Flight #3 - Ranger G2 with 8X4 Prop - Loops,Rolls, & Flaps Deployment ;-)



Here is a link to the Video:
https://www.youtube.com/watch?v=CcZh1ZxiZ10

After performing the Motor Thrust Angle MOD on the Ranger G2 it gave me space for an 8x4 Prop.
I removed the stock 7x5 Prop to conduct some Test Flights with and 8x4 Prop.
This should produce significantly more thrust than the stock 7x5 Prop.
I have this plane trimmed out pretty well now ;-)
I have increase the Airleron from 100% Scale to 110% Scale to give a bit more Airleron authority.
I think I like that additional deflection on the Airlerons.
I also programmed some down Elevator with the Flaps to keep the plane from nosing up when Flaps are deployed.
Let's see if that helps.
So let's go do some Rolls, Loops, and Flap deployment ;-)

Here is a link to the Motor Thrust Angle MOD Tutorial:
https://www.youtube.com/watch?v=v7CbbKE4ff8

Here is a link to the Motor Thrust Angle MOD Test Flight:
https://www.youtube.com/watch?v=f3JMLrpKRkI

Here is link to this Plane:

Volantex V757-6 Ranger G2 1200mm Wingspan EPO FPV Airplane PNP
https://www.banggood.com/Volantex-RC...47791920140372

Here are the Batteries I use in this Plane:

Turnigy 2200mAh 3S 25C Lipo Pack
https://hobbyking.com/en_us/turnigy-...asc=3451564005


See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

See Us On Youtube | Patreon | RCGroups | Facebook

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
https://www.facebook.com/pg/Ground-C...3132721/posts/
Posted by DutchRC | Jun 01, 2019 @ 09:09 AM | 535 Views
Halloa guys

short review this time! Of a small item: the new Runcam Racer 2..
Small. but in this case highly recommended.. I am very much impressived with camera.
This is a CMOS racing cam..

Link to the camera: Runcam Racer 2 with 1.8mm or 2.1mm lens

Runcam's 2019 Racer 2 - FULL REVIEW (Recommended) (20 min 17 sec)


Specifications:
sensor type: Super WDR CMOS
sensor size: 1/3 inch
resolution: 600 tvl
lens: 2.1 mm or 1.8 mm
field of view: 145 or 160 degrees
aspect ratio: 4:3 / 16:9 switchable
input voltage: 5 - 36 V
latency: 6 ms
size: 19 mm x 19 mm x 18 mm
weight: 5.5 grams
setup OSD: yes
runtime OSD: yes
Wide Dynamic Range: yes Super WDR
Posted by Tazkiller85 | Jun 01, 2019 @ 04:58 AM | 556 Views
Yep Les Amis,
Silence ... ça tourne !!! Comme je vous en avais parlé récemment, j'avais craqué pour cet engin et l'ai commandé directement chez iFlight. Voici donc enfin ce fameux MEGABEE ... Un 3" inspiré du shendrone squirt v2 entièrement assemblé par iFlight .Bien conçu, costaud et des finitions très propres, ce petit racer vous permettra de faire des prises de vue tout en douceur, en mode stabilisé ou en acro, dans des endroits confinés en intérieur ou en extérieur, afin de réaliser de jolie cinématiques couplé à une bonne caméra (normalement prévu pour la Gopro 7 Black) . Bien équipé avec sa Tower SucceX F4 V2 et sa caméra FPV Caddx Ratel, il est très maniable et hyper stable grâce à ses protections d'hélice qui lui servent surtout de conduits d'air qui lui confèrent une poussée supplémentaire . En bref, je ferai bien sur d'autres tests sur cet appareil, mais pour l'instant je suis très content de ses performances . Bon Film à Tous


iFlight MegaBee Cinewhoop 3" - Review Test Démo - Agréablement surpris ! (31 min 4 sec)


NOTATAZ : 17.5/20 Pour les réalisateurs en herbes !!!

Niveau : Débutants et Confirmés
Les + : Réactif, Précis, Très stable, Autonomie correcte, Doux et puissant, Très bonne qualité d'image .
Les - : Support cam non orientable, protection d'hélices cassantes sur gros chocs ...

Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous :

- IFlight...Continue Reading
Posted by Carmen Chen | May 31, 2019 @ 10:53 PM | 591 Views
Flytec 2011-5 Fish Finder 1.5kg Loading 2pcs Tanks with Double Motors 500M Remote Control Sea RC Fishing Bait Boat with Casting

Specification:
Control Time: 2-24 hours
Charging Time: 10-12 hours
Control Distance: 500M
Li-Po Battery: 7.4V 5200mAh
Controller Battery: 1.5V AA*4 (not included)
Color: Black/Green
Load Capacity: 1.5kg
Product Size: 50*27*20cm
Product Weight:2KG
ColorBox Size: 59.5*32*19cm
Package Weight:2.6KG

Main Feature:
1. Boat body adopts high quality ABS material to inject molding, more stable and firm which can againt the stong wind and wave, great outlook, exquisite workmanship and quality.
2. Double motors, huge loading Two separate bait tanks which can be controlled separately.Super large capacity baits tank,weight is 1.5kg
3. 500M remote control distance without the interference, signal is more stable under the clear environment.
4. Great value, low noise, high performance with affordable price
5. Waterproof battery power display, accurate, considerate indicator
6. Streamlined boat back design for higher speed, wind waves resistance
7. Front LED light design, convenient night version, effective fish attracting
8. High capacity Lithium battery, which is put into the middle of the boat body and more stable, can be charged more fastly and more power
9. The propeller cover can prevent the water grass from twinning

Package List:
RC Fishing Bait Boat*1, Controller*1,Charger*1,Battery*...Continue Reading
Posted by wattechighland | May 31, 2019 @ 10:21 PM | 671 Views
一般的にはrc潜水艦のwtcはアクリルパイプで作られているようですが、WWII時の潜水艦 は細長くて
前後共先細り、しかも小スケールモデルなので、サーボも入らない細いパイプしか搭載できず。
なので、FRPでハル内側に沿ったケースを作ることにします。

上部ハルの天井部分には5㎜の隙間を開けて、水と空気が入れ替わるスペースを作ってみる。
wtcに十分な浮力が出来れば、浮上した時に喫水線を下げることが出来るのではないかと予想。
浮力が足りなければ、浮力体のスペースに出来るし。

上部ハルには5㎜厚スチレンペーパーとバルサパテ、下部ハルには石粉粘土でキールとモーター部 を
カバーする。マスキングと、pva(洗濯のり)を3回重ね塗り。

樹脂が足りなかったので下部ハルだけ作業した。今回はサフェージングマット1プライとガラスク ロス
4プライでやってみた。
Posted by TMacFPV | May 31, 2019 @ 04:48 PM | 512 Views
Today, we complete the BetaFlight 4.0.2 setup of our HGLRC Arrow 3 Hybrid and take it out on its maiden flight. We also reveal the 3rd and FINAL “Keyword” to unlock the Mystery of our Upcoming June 7th Announcement. Use all 3 keywords as clues for your guess as to what the Announcement will be! Put your guess in the comments section of the video. First person (if any) to guess correctly will win a prize to be revealed along with the Announcement on June 7th! Clear Skies Friends!
3 INCH DRONE BUILD SETUP (17 min 11 sec)

Posted by Capt_Kitt | May 31, 2019 @ 01:02 AM | 612 Views
I tried to whole “let’s print an airplane “ thing again. This time it’s an ECLIPSON model T. I really had to add the nose ballast on this one. Flight weight is 930g, about 100g over ideal. I’m just hoping that the plane will hold up to the stress of flight. The quality on the parts I printed isn’t great.
Posted by captain MoMo | May 30, 2019 @ 09:39 PM | 776 Views
This is how I add the external BEC to an OPTO (meaning there is no internal BEC) ESC.

Note that if the ESC has an internal BEC you will need to remove the red wire from the lead going to the RX, otherwise you will have two conflicting voltages and burn something up.
Posted by old4570 | May 30, 2019 @ 08:45 PM | 833 Views


Yes , been raining for almost a week now ( most rain we have had in a long time ) ..
Came this morning , one WL Toys F-959 ...
Easy peasy / lemon squeezy ... Just plug in the wings and charge the battery ... Ok !

I also had to trim the rudder and elevator .. Alignment was ?
Other than that :
Engine / prop produce right on about 1:1 power to weight .. Noisy motor but no bad vibrations .
Flying weight is right on about 111 grams .

Factory transmitter blows chunks ! Ever seen a Cow blow chunks , the factory Tx blows chunks like that ..
Ele / Rud are seriously jerky
Motor = First 1/3 of throttle gives you nothing , then suddenly the power comes on .. And motor speed seems to be in 3 stages ( Feels like )
And the Rud / Ele feels the same , like 3 stages of control ( Not smooth at all )

Since the model uses the old Flysky protocol , I bound it to by Taranis Q x7 equipped with a multi protocol module ..

Chalk and Cheese folks ... Night and day , garbage and strawberries .
The difference is simply astounding .. Everything on the Qx7 is smooth ( Motor / Rud / Ele ) .

The battery goes right up the nose of the model , and there is plenty of movement / placement to play with the CG .

I will not fly the F959 with the factory Tx , it just blows .
I already set it up in the X7 .

Bad Weather , rain and more rain predicted + Winds ...
??? When I will get a chance to fly , F959 - Firstar - Ezio ...

MG 800

I saw this...Continue Reading
Posted by QuadifyRC.com | May 30, 2019 @ 05:34 PM | 750 Views
After completing a full build article here I have been flying the Hobbymate Asteroid for a few weeks and have completed my review. This review is text/pictures and embedded DVR so it's much easier to scroll through than a video review (IMHO)

https://www.quadifyrc.com/reviews/hobbymate-asteroid-3-inch-quadcopter-review

The full article above but here are my key findings:
  • This is a very premium kit for $140 and genuinely capable of 3-6s (you can choose 2700kv for 6s or 4300kv for 4s)
  • It is capable of 91mph+ on 3s or 106mph+ on 4s (GPS readings)
  • I feel the motor kV is a little too high for 4s but this can be resolved with a throttle limit
  • I was sceptical about using an EOS2 cam for FPV but the 4:3 ratio variant actually works well
  • Given the power of the motors and strength of the frame it is light at under 140g


Posted by mlilasic | May 30, 2019 @ 02:24 PM | 785 Views
Review of SL-2212A Six Channel High-speed One Key Takeoff Attitude Hold RC Quadcopter




I and my 5 year kid tested this quad and it flies great. Perfect height hold and very robust, my kid gave it few crash tests.
On low rates very smooth but on high rates very agile. Flight time is more than enough to have some real fun.
I can recommend it for kid pilots and for first time pilots who want chep start in the hobby


Description:
  • Battery: 3.7V 380mAh ( included )
  • Charging time: 60 minutes
  • Flight time: 7 minutes
  • Maximum Flight Speed: 2.5m/s
  • Remote control distance: 30m
  • Remote control battery: 3 x AAA ( included )
  • Color: Blue & Camouflage
  • Quadcopter Size: 26*15*10cm



Features:
  • Attitude Hold mode provides stable flight
  • One key takeoff
  • Easily control aircraft by controller no need by hands, more convenient and quick
  • Large capacity battery
  • Battery life up to 7 minutes



Functions:
  • Forward/backward
  • Turn left/right
  • Sideward flight
  • one key takeoff
  • one key landing
  • Three speed mode


In the box:



1 x Aircraft
1 x Remote Control,
1 x Charging Cable
1 x Screwdriver
1 x 3.7V 380mAh Battery
3 x AAA Battery
1 x English Manual


Light show:

SL-2212A Night Flight - Six Channel High-speed One Key Takeoff Attitude Hold RC Quadcopter (0 min 21 sec)




and crash test by my 5 year kid:

SL-2212A Crash Test - Six Channel High-speed One Key Takeoff Attitude Hold RC Quadcopter (0 min 10 sec)
...Continue Reading