R/C Blogs - RC Groups
Shop our Airplanes Products Drone Products Sales
Posted by KatrinaRosen | Today @ 09:17 AM | 114 Views
A drone flies dangerously close to an A380 during take off. The video shows an Airbus A380 taking off from the Plaine Magnien Airport located on the Mauritius Island in the Indian Ocean. The A380 is the largest commercial airliner in the world and can carry more than 500 passengers in a typical three class seat configuration and up to 850 passengers in a densified all-economy cabin version. As the jumbo jet takes off from the runway 14, the prepositioned drone films the plane passing dangerously close at about 300 feet from the tip of the left wing. The airliner belongs to the Dubai-based company Emirates. It seems to be the 4:35 p.m. flight EK702 on regular schedule to Dubai airport.
Posted by FeiJi | Yesterday @ 09:13 PM | 357 Views
Not quite finished, needs a couple of hatches made but it is functional and ready for maiden which I could do tomorrow but will probably wait to get a headmount for my phone camera to take videos. CG is back about 23 cm and had to use a little ballast to get it to balance. Could use a much heavier motor and/or battery with more thrust - this little motor gives about 1:1 but the lift should be awesome as the AUW is 340 grams. I added some tape covered skids on bottom to protect fragile leading edges and to keep motor mount from digging into ground.

If it flies nice I might try faster prop rather than this slowfly prop, and add a rudder with 5g servo. Also could go with a bigger motor.

Excited to fly it but am thinking about my next project already which will be a scratchbuilt hotliner using same 5mm epp foam and fishing pole tubes and just elevons with only a vertical tail.
Posted by Dave_K | Yesterday @ 08:44 PM | 376 Views
The first plane I bought was the AXN Clouds Fly motor-glider.

This wiki has a ton of information on this plane and if you have this plane, I highly recommend checking it out!

My first experience flying this plane was very scary. Me and a buddy went out to the field and asked an experienced gentleman for some advice. He was very helpful and even maidened and trimmed the plane.

I took the controls from him full of confidence and very soon got disoriented. I managed to put the plane down safely and carried it home in one piece. My subsequent visits to the field didn't end this well.

Before this first time having flown I haven't flown with a simulator before and I feel that was a big mistake. I only recently got a simulator, Aerofly RC, and I very much regret not starting out with the sim. I've flown now for a few hours and already feel MUCH more in control when flying the plane on the sim, I haven't yet flown the real plane after the sim, and will give an update here once I have done so.

Here is a weight breakdown of my AXN:

Airframe (inc. servos and motor) 356.6 g
Carbon spar 31.5 g
ESC 30.6 g
Receiver 8.2 g
Battery (avg) 178.25 g
Tot (g) 605.15 g

The AXN has a wing area of...Continue Reading
Posted by Bill M - RC | Yesterday @ 07:44 PM | 413 Views
Hi fellow Pilots & rc enthusiasts


MJX Bugs 5W B5W review. This Bugs 5W review of this great 5G WIFI FPV with 1080P Camera GPS Brushless Altitude Hold RTF RC Quadcopter Drone includes: How to use Waypoint & Track Flight + CRASH Report.

IN STOCK HERE NOW: https://goo.gl/BMp7UZ

MJX Bugs 5W B5W GPS FPV drone review - How to use Waypoint & Track Flight + CRASH Report (14 min 51 sec)

Posted by Dave_K | Yesterday @ 07:33 PM | 412 Views
Howdy world.

I am new to the RC world and here I will take whoever is interested along on my journey and learning.

Stay tuned.
Posted by kydawg1 | Yesterday @ 06:44 PM | 418 Views
Posted by MarianoJuarez | Yesterday @ 06:13 PM | 36 Views
Has anybody tried or knows for the specs, if the Venom 15C 3S 4000mAh 11.1V LiPo Drone Battery (Link Below) will work on the Parrot Disco?
Im about to buy the drone, and would like to know if they work since the Multistar High Capacity 3S 4000mAh Multi-Rotor Lipo Pack are out of stock.
Im new here and know nothing about drones or batteries.
Thanks a lot

Posted by ww2collector | Yesterday @ 06:04 PM | 445 Views
I've received a few inquiries from fellow RCG'ers asking me about the Fall Kutztown Swap Meet. All I can tell you is that according to the Kutztown Fair website, there is a swap meet scheduled for Saturday, September 15th, 2018. The Kutztown Aerodrome website has no info posted as of today.
Posted by MarianoJuarez | Yesterday @ 06:04 PM | 36 Views
Hi, Im new in the group and arround RC planes.
Im about to buy a Parrot Disco, and I have some questions about the Battery
I read about the Multistar High Capacity 4000mAh 3S 10C Multi-Rotor Lipo Pack and the Multistar High Capacity 5200mAh 3S 10C Multi-Rotor Lipo Pack, and hear they work fine, but im unable to find the 4000mah one. They are out of stock, and dont sell them anymore.
I want this one in particular because Ill add some extra weight to Disco (with a GoPro H5B), besides the battery.
The Idea is to use the FreeFlight Pro to do a mision, with same altitude all the time and get the max amout of flight time possible. I think the 4000mah will do much better than the 5200mah, because of the weight.
Ive seen this Venom Batteries online, but nobody talks about them for the disco (Venom 15C 3S 4000mAh 11.1V LiPo Drone Battery - Uni 2.0 (XT60, EC3, Deans) Plug) Link Below
Can anybody help me with this issue?
Does anybody know how much weight the Disco can handle?
Thanks a lot

Posted by mnemennth | Yesterday @ 04:23 PM | 499 Views
Archiving and Decommissioning 10 years of Old Hard Drives... a Timeline:

I just spent the last 4 daze in a sleep-deprived haze deliberately destroying my 4th order data backups and turning them into modern art as they had reached critical mass. Much hilarity ensued.


"I love the smell of angry pixies in the morning..." ~ me

Originally Posted by mnemennth on: July 17, 2018, 03:06:36 pm

I've been consolidating pics, videos, documents and music from various old hard hard drives from the last 10 years into a single contiguous archive (hopefully with minimal file duplication) so I can decommission the hard drives. I've been at it for two... sh**... three days, and I'm about half done.

I'm so feeling my inner CodeMonkey right now... have consumed nothing but caffeine & leftovers since Saturday. Gauging from razor stubble, been similar time since last shower. Sleep is a stranger to me.

Please shoot me now.

...Continue Reading
Posted by gquiring | Yesterday @ 01:16 PM | 778 Views
The drifting vario problem with the G-RX8 can be a bit disappointing. It's been suggested that once the RX is on for a couple of minutes the drift has settled down. But resetting the vario from wheel button is a bit awkward if you are holding the model in your hand. So I setup an additional function on my timer/throttle lock switch to also reset the vario. It works by looking at the timer, if the timer = 0 then it's the first time going so reset it when you unlock the throttle and start the timer. Once the timer is no longer 0 it won't reset it.

Frsky G-RX8 reset drifting vario with your throttle lock/timer switch (3 min 37 sec)

Posted by Zelight | Yesterday @ 12:17 PM | 796 Views
Posted by jimharley909 | Yesterday @ 10:06 AM | 873 Views
I lost my dad to diabetes in 2007. There isn't a day that goes by that I don't see his influence on who I am. Sometimes good and sometimes bad. In the grand scheme of things, I was lucky to have a dad that had an interest that we both shared, it was our common bond no matter what. He always blamed having me killed his full scale flying days...tongue in cheek...but R/C was something he could afford and pass along to me. He taught me a craft, how to build airplanes, work with wood, and care about quality and craftsmanship. This translated to flying, be the best you can be, learn aerodynamics, learn why an airplane can fly...all the fundamentals. In grade school, while kids were reading Cat in the Hat, I was reading the FAA private pilot course books. I didn't do it because he made me, I did it because I truly loved it, and I have him to thank for putting me on that path. My Dad was a draftsman, another skill he passed along, so now, in the days of the ARF, kits are hard to come by and it is literally back to the drawing board. Now that I'm back to R/C, there is a lack of kits and I'm drawing up my own plans. Thanks Dad, gone too soon.
Posted by Bazzboe | Yesterday @ 09:39 AM | 856 Views
To Whom It May Concern,

I Bazzboe( user name), Benchmark R/C Pilot Displays will be on a short vacation for a couple of months due to commitments beyond my control.
Not to worry we will be back within 2 months and hopefully by then be caught up and finished with our web site design, a solid new facility location, and a production and management team to take us to a higher and much more sustainable level. I will be doing price changes (regretfully but unavoidable). But we will always honor some sort of discount to repeat customers and those who wish to be dealers of our products.
If you have a pending order with us ..IT WILL BE FULFILLED ASAP! No new orders will be taken at this time. If you wish to be put on our mailing list for future knowledge of when we are back please send us your email at bmarkrc@gmail.com and put the words mailing list in the subject heading.
With all my best,
Michael Hicks
812-646-0852 CST
Posted by grmis | Yesterday @ 08:41 AM | 896 Views
This is my (second) EDF jet. It now has about 40 flights, and I recentlty installed a flight controller in it. So it is perhaps time to post here a few lines and a few pictures about it.

- Stock motor, stock ESC, stock servos, Turnigy 4S/3000mAh Lipo
- Home made after-burner LEDs, with Arduino and programmable RGB leds (see here for details)
- Flight controller: Omnibus F4 v5, with iNav 1.9.
(PWM1: ESC; PWM2: unused; PWM3: Aileron1; PWM4:Aileron2; PWM5: Elevator; PWM6: AfertBurner module; UART6: SBus; UART3-TX: uninverted SmartPort; UART1: GPS(future)). In case someone is interested by the detailed parameters (PID etc), I attached my configuration (dump). The stabilization (angle mode or acro mode) is quite useful when launching the plane, and also for landing. I can now land by glidind "hand off" in angle mode !
- Radio: FrSky XSR receiver (connected to the FC via SBus & SmartPort telemetry). Taranis X9D programmed with 3 flight modes (Manual/Acro/Angle) and flaperons (via iNav servo mixer and 2 AUXchannels).
- To be added soon: GPS, to get the speed (via telemetry).
Posted by mwhidden | Yesterday @ 08:32 AM | 897 Views
Turns out that the Mark's Models instruction booklet skips over a few steps. Although shown in the plans, the instructions don't mention the installation of the 3/16" square wing supports along the top of the fuselage. These run through the cutouts in the center two bulkheads, so I had to notch the bulkhead that I had installed upside down. It also omitted the horizontal braze at the tail,so I put that in as well.

I sheeted the bottom of the fuselage, but forgot to glue the sheeting to the bulkheads, so I came back with thin CA to fix that. With a knife, I pared away the excess sheeting, working from nose to tail so if the balsa split, the crack would run away from the fuselage, not toward it, and the grain drew the knife away from the sides, not towards. Then I sanded it flush.

Since I'm planning to put an electric motor in this sailplane, I cut a plywood firewall to the shape given in the plans. I used some leftover plywood from an unrelated laser-cut kit of Tiny Whoop gates.

Shaping the canopy was tricky. I transferred the profile of the nose end to the end of the balsa block. Then I sketched the slope of the canopy along the sides, and marked the tail end profile on the back of the block. Then I spent a long time with a coarse sanding block hand-sanding it to the rough profile, and touching up with finer sand paper.
Posted by Hobby WOW | Yesterday @ 04:51 AM | 969 Views
2.4G 4CH
Forward, backward, turn right /left, turn over (180 degree )
Switch to left /right manually , with LED screen .

Posted by Yowoo Linda | Yesterday @ 01:03 AM | 1,025 Views
😈Used HRB lipo battery in stock🎉
Send from Pennsylvania, USA

HRB 6000mAh 2S 7.4V Hard Case Lipo Battery 60C
US $27.39 only one piece

3S 2200mAh 11.1V
US $16.64 only one piece

HRB 6S 22.2V 5000mAh EC5
US $59.86 only one piece

HRB 5S 18.5V 6000mAh
US $54.51 only one piece

HRB 14.8V 3000mAh LiPo Battery 4S 35C
US $28.56 only one piece

HRB 6S 22.2V 6000mAh LiPo Battery 50C
US $69.92 2pieces

HRB 3S 11.1V 5000mah LiPo Battery 50C
US $32.96 4 pieces
Posted by rinoki71 | Yesterday @ 12:46 AM | 1,052 Views
The EVO is really nice. There's a few minor issues Autel needs to correct but the camera is stellar and it flies smooth. The dynamic tracking also works amazing. If Autel gets the bugs fixed soon then this will be a huge hit and serious competition to DJI.

Autel EVO Full Review with Flight Test (37 min 12 sec)