Posted by VicT | Mar 04, 2019 @ 01:20 AM | 1,666 Views
Stock 10BL 800 KV motor with 50 amp ESC and 3S 2200 and 4S 2200 Turnigy Graphene
11/7 3 blade prop
26 A, 256 watts, 45 A, 650 watts
With 10/8 5 blade Eflite Spitfire 1.2 prop
24 A, 235 watts, 50 A, 690 watts
Posted by Pierre_de’ Loop | Mar 03, 2019 @ 10:27 PM | 1,564 Views
This dashing fellow started life as a Williams Bothers race pilot, but he’s decided to pilot my Taube instead.
Posted by Chandler Bing | Mar 03, 2019 @ 10:20 PM | 1,338 Views
welcome to an inquiry:


Drone is not Luxury any more
Chandler ShawRegional Sales Manager
Office:0755-85270104
Phone:+86 13556317273
Whatsapp/wechat:+86 13556317273
Skype: Chandler shaw
www.cfly-cn.com
Posted by old4570 | Mar 03, 2019 @ 09:13 PM | 1,715 Views
Completed this morning ..
I decided to glue the wing in ..

The weight came in at 110.4 grams ready to fly ( Flying weight )



I used 5 minute epoxy to glue the wing , but epoxy needs to cure ...
So I also used some Hot glue to hold the wing and create some load bearing points ..

It's warm again , ok hot ! Not as bad as days past , but with cloud it's humid warmth .. ( My Fav ) ( Not )

Just need to go out and do some glide or glud ( smack the ground ) tests ..
Posted by QuadifyRC.com | Mar 03, 2019 @ 07:58 PM | 1,399 Views
I've finally finished my build, setup and review of the Eachine Tyro79 in text/picture format.

Given the spec I was expecting it to fly like a pig but it was much more nimble and certainly more effecient that I'd expecting.

The camera started off ok then lost the ability to see in shadows at all so I'd budget $15-20 for a replacement. Is it still a good deal for $95-100? I think so but it is closer to the price of other 3" PNF quads.

https://www.quadifyrc.com/reviews/ea...tup-and-review



Posted by Bill M - RC | Mar 03, 2019 @ 02:49 PM | 1,628 Views
Hi fellow rc pilots & rc enthusiasts

HBRC HB64X Brushless Micro FPV Racing Drone review. Short FPV camera action clips of an indoor whoop track and some flips & rolls.

Get 20% OFF this HBRC HB64X Brushless Micro FPV Racing Drone using discount code: BillMRC here now: http://bit.ly/2E4cRLO

HBRC HB64X review - FPV Action clips (2 min 20 sec)

Posted by GroundControlRC | Mar 03, 2019 @ 12:28 PM | 1,552 Views
Glue & Fly Series - F-22 Mini V3(B) - Flight 27! She's all Trimmed Out!



Here is a link to the Video:
https://www.youtube.com/watch?v=XEwH_dTN04Y

I have this Parkjet all trimmed out and have the CG well balanced ;-)
The plane tracks extremely well and stays where you put it.
The Nose stays nice and level with abrupt Full Throttle at level flight ;-)
I measured the CG after getting back from the Flight Session and it is located 45mm forward of the front of the Prop Slot, or 11mm back from the top of the cutout for the Servos.
That's approx. 10mm further back than when I performed the Maiden as it felt a tiny bit nose heavy.
I have found that it takes time getting used to a completely neutral balance on the CG.


See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

See Us On Youtube | Patreon | RCGroups | Facebook

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
https://www.facebook.com/pg/Ground-C...3132721/posts/
Posted by mtdoramike | Mar 03, 2019 @ 08:11 AM | 1,682 Views
I finished this Creole Queen, which was half built when I received it, but after about 300 hours later, she is finished.
Posted by old4570 | Mar 03, 2019 @ 12:30 AM | 2,184 Views
Talking about how much $banana I had invested in the R3 project motivated me some !
$13 ozzi banana in materials and another $19 in electronics . Yes , that's about what you pay in Oz for a pack of smokes ..
So it's not the most heavily invested in project , and certainly no outsourcing of funds was required

Control rods were formed , servos located , the receiver was soldered ( servo pins ) and then bound to my Jumper T12 .
After some quick checks for control surface throw , a quick adjustment was made on the elevator .
Once I was satisfied , the servos were glued in place .

The fuse is pretty much done !

1) Still need to make a canopy ..
2) After a canopy is made I can select a suitable 1s battery and play with the wing location for that all important CG

It's hot outside , and cloud just rolled in about an hour ago driving up the humidity , so it's a steamy hot ^*&%^$ outside !
Important thing is to keep pushing the project forward .. After all it's costing me ! ( )

Minions Banana Song Full Song (3 min 59 sec)


Here is a plug for what is fast becoming my go to budget 4ch receiver .. ( Discounted At The Moment )


Posted by old4570 | Mar 02, 2019 @ 08:13 PM | 2,131 Views
Not happy Jan ...

NOT HAPPY JAN - Yellow Pages Ad (0 min 30 sec)



Just finding it hard to motivate myself !

Costing the R3 Project ... ( Attempted Motivation )

I thought about how much the R3 project was setting me back financially ...

The most expensive component is the Rx at some $12 ozzi bananas ..
The next most costly is the servos at some $7 ( Pair )
The 6mm Carbon Tube is about $3.50
Control rods ( music wire ) $1.50 for two
About $2 worth of Depron
Maybe $2 for the control horns
? off laminating film , lets call it $1 so we have a figure ( More like 10c or 20c / maybe less )
$1 worth of glue
20c worth of fiberglass
$2 of balsa
? scrap carbon

So there you have it .. $32 ozzi bananas ... Less the battery ..
The average cost of a pack of cigs is $30 ozzi bananas ...
So the project is worth one packet of cigarettes ! ( I don't smoke ) , and no I wont trade ..


The cost of the R3 less electronics
$13 ozzi bananas ...
Posted by KiT FPV | Mar 02, 2019 @ 03:49 PM | 1,824 Views
Ran one pack pair through this. When I first plugged it up the change gear servo did not work out of box so traxxas sent me a new one. Routed it through box opening.
Posted by GBLynden | Mar 02, 2019 @ 02:48 PM | 2,102 Views
This is my buddy Bill's Maiden Flight with his Force RC F-18!

Bill's Force RC F-18 Blue Angels 64mm EDF Jet Maiden Flight (4 min 47 sec)

Posted by alex_nikiforov | Mar 02, 2019 @ 11:46 AM | 2,029 Views
Full review, subtitles are available with translation into any language.

URUAV UXII Patch Antenna. Наземный тест дальности. Banggood (4 min 52 sec)


Links:
URUAV UXII Patch Antenna https://goo.gl/y9k5LM
Realacc Panel Antenna https://goo.gl/Ep5pvK
Triple Feed Patch-1 https://goo.gl/DQq9ic
FPV Monitor https://goo.gl/xhUucX
Posted by PeterVRC | Mar 02, 2019 @ 09:59 AM | 2,006 Views
I do already have the 2300mm FMS Fox Glider - which is a very good, well made, glider.....
I partly got the 3000mm version as that is more ;serious'... more capable.. plus uses the same 6S batteries that my 80mm EDF's use, so taking the Fox with them (EDFs) means that if I don't fly the jets as it is too windy, or some reason, then I can just fly the Fox - as gliders don't care too much about wind levels.
Of course I can just take it and fly it anytime also....

Near 6Kg AUW!! Wow.....
My 4m DG-808 (FlyFly... and broken for now!) is under 4Kg AUW ! But it is a performance thermaling glider... not aerobatic...

The FMS Fox got a lot of good reviews, and nothing seen to be negative about it. Too bad that doesn't always mean a lot anyway! But what can you stuff up on a 'simple glider' anyway??? Thus it should be good/fine.... and the FMS 2300mm version is, so...

Interesting is that is uses NO GLUE.. and NO SCREWS... to assemble it. It is all done via plastic keys parts and sprung clips to lock them into place. This makes transporting it easy (as easy as per any), but FAST EASY assembly at the flying field..... and to disassemble it and pack it up! This was another reason it seemed a good thing to have....

....
Posted by old4570 | Mar 02, 2019 @ 06:49 AM | 2,144 Views
Damn it's hot ...

Everything is starting to look like a corn chip , and sound like a corn chip ..
Even SPF 50 is not cutting it !
Where the hell do you buy SPF 1000 ( ? ) , I am really sick of burning .. ( Might need lead based paint to protect one self from the UV )

Where are we ?

R3 ( Ripit 3 )

Control surfaces are mounted on the boom , control horns put in place ...
Just need to make some holes in the tail boom and I can connect the control rods to the Rud/Ele ..
Then locate the servos , solder up a Rx ( FS2A ) and start playing the CG game ..
Posted by Tazkiller85 | Mar 02, 2019 @ 05:48 AM | 1,828 Views
Yep Les Amis,
Pas le temps de visser ? Clipsez ! Aujourd'hui, un petit test en vol des moteurs Happymodel "Montage rapide" avec les hélices 5063 assorties. Une finition plutôt correcte pour ces moteurs très abordables (moins de 9€ pièce ), efficaces et pratiques, ils vous faciliteront la tache pour le remplacement de vos hélices tordues ou cassées. Pas idiot non plus le fait de pouvoir remplacer l'axe facilement en cas de "vrillage" . Les hélices associées sont résistantes et de bonne qualité même si je n'ai pas eu l'occasion de me crasher ... En bref, pour l'investissement, je suis agréablement surpris et je trouve intéressant d'avoir un quad monter comme ça pour les séances d'entrainement . Je Valiiiide ! Bon vol à tous .

Happymodel Moteurs Brushless SE2306 2700KV ... Test trankilou Pilou ! (19 min 0 sec)


NOTATAZ : 18/20 Intéressants pour le Freestyle !


Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous :

COUPONS BANGGOOD : 502C6B rchobbies8
- Moteurs Brushless SE2306 : https://goo.gl/3tV4T6
- Hélices 5063 : https://goo.gl/e449ge
- Capuchons Alu : https://goo.gl/qr5WR1
- Axes moteur : https://goo.gl/dGXqyC
- Buzzer Autonome Vifly : https://goo.gl/QRXec9
- Buzzer Autonome JHE42B : https://goo.gl/zV2zdM

- 10 à 12% sur tous ces produits, CODE MarPaypal10% : https://goo.gl/88bnhn
- 15% sur les caméras : https://goo.gl/tRWLSC
- Multi Promos et coupons : ...Continue Reading
Posted by alex111 | Mar 02, 2019 @ 02:29 AM | 1,768 Views
My model ferry at Boondall boat club today
Posted by simages | Mar 01, 2019 @ 10:14 PM | 2,189 Views
Specifications

Wing span – 40 inch / 1014mm
Length – 43.08 inch / 1095mm
Wing area – 582.4 sq inch
AUW (ready to fly including battery) ~ 38.45oz / 1089gr
Wing loading – approx 9.5oz sq ft!!

PA Ultimate AMR

My Airframe order included;

Ultimate AMR 40 ARF - Red, Airframe
PA Thrust 40 brushless outrunner
PA Quantum 45A ESC Pro
Nexatec NXT 70HV servo - Pack of 4 servos
Carbon fiber MD size long servo arms -set of 4pc
Thin gauge electric extension lead - 2 meter / 78"
VOX 13x8 Electric wooden propeller
1.8" Carbon Fiber Ultimate Style CNC machined spinner

Build Thread HERE