Evergreen aeromodelers event.
Some fun events and lunch time demo, rocket gliders were very cool.

Foam fest 2015 (7 min 5 sec)

2015 Float fly (5 min 47 sec)

We had a nice spring day and made a vid of some of us.

March 2015 Team (3 min 42 sec)

Our clubs Elec event at the Evergreen Aviation Museum.

Electric Goose 2014 (5 min 40 sec)

I gave rides on my Radian with the Fatshark fpv and had a candy drop for the kids.

Valley Veiw fun fly (5 min 14 sec)

My latest endeavor

Radian Fatshark (3 min 51 sec)

I don't do control line but our club EvergreenAeroModelers hosted a fun fly and I made this little vid for them.

Control Line April 5 2014 (3 min 36 sec)

Having snow in the Willamette valley is very beautiful.

Feb Snow quad video (2 min 22 sec)

Jan 1 2014
club had a chili feed and fly day, a little foggy but great fun.

Polar Bear 2014 (3 min 34 sec)

Short blooper clips from this summers flying here in McMinnville, from both clubs.

Bloopers (1 min 14 sec)

I have been working on videos as much as the flying. Here are a couple trailers from our towns 2 Rc clubs that I made.

The Electric Goose (0 min 55 sec)

Trailer for Mam (0 min 46 sec)

...Continue Reading

Omega 130g Brushless Outrunner

Peak Amps: 50A
Peak Watts: 700W on 4S, 525 on 3S
Weight: 130 grams
KV: 870

3s
2650mah
13x6.5 53amps

4s
2200mah
13x6.5 64amps

ice 100 esc and exceed monster 46
Model #:
Monster Power 46 (63M54)
Kv: 670Kv
Input Watts: 800W
Resistance: .04 Ohms
Idle Current: 3.90A
Cont Current: 40A
Max Current: 55A
Cells Li-Po: 4-5
Weight: 12.2 Oz (310g)
Overall Diameter: 2.0 In (50mm)
Shaft Diameter: .32 In (8mm)
Overall Length: 2.15 In (55mm)

5s
14x8 67amps
14x10 69amps

Need to keep track of great info.

fly a "stabilized approach". This means that your landing approach is stable, in that it has no time limit. You could start your approach at 20 feet high or 2,000 ft high, and you can fly in this mode as long as you want.
https://www.rcgroups.com/forums/show...ostcount=11495

The Right Way to Set Up Servos
http://www.modelairplanenews.com/blo...set-up-servos/

Grab every part of the airplane. Pull on every part. Make sure all hinges are glued. Make sure all control horns are glued into the surfaces (I see this a lot). Make sure the pushrod connectors are tight. I have seen every possible part loose.
https://www.rcgroups.com/forums/showpost.php?p=18907877&postcount=22436

Peter Goldsmith
Trimming Procedure crucial to trim your model in the correct sequence to make
sure each adjustment has no effect on the previous adjustment
http://www.freewebs.com/scrcflyers/P...0Procedure.pdf

Ok here is the vid, shows pics of the assembly and maiden flight to trim it out.

300 shp 1st flight (5 min 24 sec)

First balsa plane





...Continue Reading

After the f86 vid Shawn and I went up with the 808 keychain cam with a couple planes.

clips (2 min 50 sec)

Great job Shawn

July F86 (4 min 41 sec)

I got one of the 808 keychain cams and have to say it's pretty darn good video for $12. Mine is the #11 model I think but they say on http://chucklohr.com/808/ that #16 has the best vid quality. So I tried it on the front of the wing and rear stab with some velcro and having part of the plane show in the video frame helps alot for viewing. So here is the vid from the rear horizontal stabilizer.

808 camera (2 min 10 sec)

I flew the edf finally. I shortened the vid because the last part the wife just had blue sky. Landing was ok but our temp runway is raised and rolled off the end putting some damage on the nose gear.

F86 (1 min 32 sec)