Posted by | Jun 18, 2020 @ 05:21 PM | 5,894 Views
The below link is an extremely comprehensive brushless upgrade guide for your WL Toys 144001 buggy that will take you through EVERY step to install the brushless power system and associated parts. There are almost 60 photos and a full step by step guide to walk you through the process as well as a full parts list.

Benefits from this 2838 brushless setup over stockinclude:
  • Stronger acceleration
  • Higher top speed
  • Better front/rear and left/right weight balance
  • Lighter overall weight
  • Ability to run 2s or 3s safely
  • Much better battery life
  • Greater crash resistance since car carries less momentum.

If you are just looking for the 2838 motor combo it can be found here: $28 Brushless 2838 motor / 35A esc combo
Posted by rchrist | Jun 18, 2020 @ 05:21 PM | 6,009 Views
Finished converting my fp fx070c to cp. Couple more things to tweak. Awesome results.

Edited 06-25-20: I started this project with the cc3d flight controller - had a few ups a downs and decided to try a k-bar unit I had for years and never used nor tried in a heli. All the axises are clicking on the bench getting ready to air test. Didn't take long to figure out how to setup the brushless tail and that's going to need some tweaking once airborne. Meanwhile, I got a k124 flight controller on order for it as the easiest setup. Also got a micro brain 2 as another option. The cc3d is the hardest of them all to tweak for great flight and I was close before now trying the k-bar. The cp function is awesome in it and it scaled flied nicely with the cc3d. I also had to take it from 4s to 3s - to much power with the oversized motor. I now have a footprint of how to convert fx070c to cp. Transplanting another unit into the shell seems much harder than converting. Oh, and it sounds awesome also - no more gear to gear noise.

Posted by peter24 | Jun 18, 2020 @ 01:04 PM | 7,714 Views
This a plane I've been working on for quite a while,
Modelled in solidworks with help from several threads on here, and made for 3d printing using inspiration from dirty dee's A330 build thread.
Never designed a plane from scratch and certainly never printed one, so how it will turn out who knows.

Plane is sized for parkjet type power system, as that's what I has laying about.
Wingspan 700mm.
Fuse length 643mm.
Weight of printed parts approx 550grams.
6x4 prop
5x 5g servos
25amp esc.
3 cell lipo, 2400mah.

Will add some pictures of the model and the 3d printed test parts I have so far.

Feel free to add comments, improvements, ideas,
Its all a learning curve.
Posted by fastmax | Jun 18, 2020 @ 10:55 AM | 6,275 Views
Here's another Whoop build. Can never have too many Whoops! This one is a bit of a Franken Whoop. It has a Blade Inductrix FPV Plus flight controller, and camera combo mounted in a NewBeeDrone Cockroach frame and Goober canopy. Props are NBD Azi, and motors are Tiny Whoop Special Sauce.

This little Whoop is an excellent flier, and has become one of my go to Whoops for buzzing around the house and ripping around the backyard. Here's a few pics. Video, and DVR footage coming soon.

EDIT 6/23/2020 FPV Maiden Flight

BumbleWhoopDuctrix Franken Whoop Build FPV Maiden (1 min 22 sec)

Posted by BDOG1 | Jun 18, 2020 @ 08:33 AM | 6,241 Views
While the wind has subsided for the moment so , I have also been finishing some Gas projects that have been on my "to do list"
Pictured below is a 1/4 scale cub that I have been working on .
A Enya120 R has been mounted for the power system { I wanted to use a gasser but my 23cc is side exhaust and would require cutting up the cowl more than I wanted } ,a different spare set of wings have been moumted and all servos have been installed.
Next I fabricated new wing struts and hardware -see below
Posted by RogerMaz | Jun 18, 2020 @ 02:35 AM | 6,647 Views
There has been some discussion the various types of tabs used on aircraft so I thought I would add my two cents worth of thoughts on the subject gathered from a lifetime of working on aircraft..
By definition secondary flight controls reside on primary flight controls - ie. tabs. There are a myriad of different types of tabs usually defined by their intended function and it is quite common for more than one of these functions to be incorporated into a single tab.
Where the confusion often arises is that different manufacturers use different terminology for these functions.
Posted by ROlive6677 | Jun 18, 2020 @ 01:55 AM | 6,649 Views
Its malfunctioning it will not connect with remote once i turn it on it goes full throttle with remote off . Only had it for 6 weeks.
Posted by Flashhobbyrc | Jun 17, 2020 @ 10:14 PM | 7,043 Views
Hello, Friends,

We are back with a new brand, who am I? You will know who am I when you use our products.

And now, we released the new series motor this month with more competitive price, and the MAP is US$16.99/pc for 2207.5 motor.

- 1900kv, 2450kv, 2750kv for the selection
- NSK 684 Bearing
- Over 1.9kg Pull with GF6045 prop
- 0.15mm Silicon steel sheet from Kawasaki, Japan
- M3 screw to fix the shaft

If you need more information, pls click our website:
Posted by Amanda BH | Jun 17, 2020 @ 08:45 PM | 6,718 Views video from Dutchrc adventures, you can get more hyperbola 5" BNF drone details from it
Posted by HugoC | Jun 17, 2020 @ 06:40 PM | 7,081 Views
While the DX5e transmitter is one of the best values in RC, it is anything but a stripped down transmitter. In fact, it boasts many features you simply won't find on most transmitters in its price range. Things like a Hi/Lo control rate switch, an extra function switch and available Delta wing mixing.

And because it's a full-range 2.4GHz transmitter, you can use the DX5e with everything from ultra micro helis and airplanes to bigger scale trainers and sport planes. It's a great way to try out the exciting world of Bind-N-Fly aircraft, too. It's 5-channels and extra functions will allow you to fly just about all of them.

Basic 5-channel 2.4GHz DSMX radio and receiver
Easy-to-use control for basic models
Includes AR610 6-channel full range sport receiver
Delta wing mixing
HI/LO rates
Servo reversing
JR and Spektrum compatible trainer system

Look this video
Posted by VicT | Jun 17, 2020 @ 05:46 PM | 7,057 Views
The purpose of this How To article is to explain how to use Flight Modes on the DX9 transmitter for elevator trim.
Any of the talking DX transmitters and e (non talking computer transmitters) have the programming waiting for you to use. Flight modes can be used for other trims and things but this will cover elevator trim only.

Background: Elevator trim will change according to the airspeed of your model. If there is any incidence between the wing and stab you will have pitch up according to the airspeed. If you have little to no incidence then there will be little to no pitch up with airspeed changes. If you want to fly inverted with out having to hold any down elevator then you might want to have no incidence and/or move the center of gravity back so that there is little to no elevator stick required. Assigning a switch to give you a certain elevator trim to fly hands off might be another use of flight mode trim however this article is for basic flight control where minimizing pilot workload is the goal. This article is aimed for those that do not understand the value of using transmitter flight modes. The article does not go into flight modes for receivers or stabilizers or gyros. Transmitter flight modes can be used for receivers such as the Apprentice receiver, the AR636 receiver and the AR637T receivers. The 636 receivers usually are programmed to provide pitch up with full power. Many find this reduces pilot workload. Others dont like it...Continue Reading
Posted by Firefighter5231 | Jun 17, 2020 @ 02:08 PM | 7,140 Views
I have a ft009 boat I have put new batteries in the controller and fully charged the battery pack and the rudder moves like normal but the motor won't turn when hitting the throttle
Posted by DutchRC | Jun 17, 2020 @ 01:45 PM | 7,240 Views
Halloa people

sooo have you noticed rc-motor companies are getting into RTF quads? Here is another one of those but I will say I wanted one as soon as I saw the first rendering :$
So yep.. BrotherHobby has brought us a quad we don't need to build ourselves An ultra-light 5" in this case or maybe we should call it a "twig" ?

Link to the quad: BrotherHobby HyperBola 5 FrSky BNF

I'll be doing several video's on it (if it holds up ) so lets have a first look at it first

the Impressive HyperBola 5 from BrotherHobby! - Show & Tell (14 min 18 sec)

type: racer / funflier
base thickness:
material(s): carbon fiber + plastick canopy
dry weight: 147 grams
flight controller: HGLRC Zeus 35A 5-in-1
firmware version: 4.1.5
ESC's: HGLRC Zeus 35A 5-in-1
motors: 2004 3150Kv
propellors: Gemfan 5125 triblades
FPV camera: Caddx Ratel 2.1mm
Lipo: 600mah - 850mah 4S (not included)
OSD: Yes, Betaflight
smart Audio: Yes
buzzer: nope
LED's: nope
spare props: nope
Posted by rommel7645 | Jun 17, 2020 @ 08:28 AM | 7,080 Views
Profile f35 maiden motor 2212-2200 kv 6x4 3s 2200 40c
Posted by Tazkiller85 | Jun 17, 2020 @ 05:04 AM | 8,244 Views
Yep Les Amis,
Plein les oreilles ! Comme je vous le rpte assez souvent, je suis aussi, fan de High-Tech et de matriel audio vido. Donc j'ai en test aujourd'hui un casque audio bon march, le A70 Fusion de chez OneOdio. Aprs un lgre dception en dcouvrant son aspect un peu cheap du plastique PVC dans cette couleur mtallise, j'ai t de bonnes surprises en bonnes surprises. En effet, un bon son, une puissance surprenante et un excellent confort, ce petit casque bluetooth m'a vraiment surpris par ses qualits. Ce rajoute a, ses deux prises jack qui permettent de partager sa musique ou de mixer deux sources diffrentes ! En bref, un excellent rapport qualit prix selon moi ... Bon Film Tous et Merci de votre soutien .

OneOdio A70 Fusion / Casque Audio double entrées - Test Démo Review - Petit prix Grosses perfs ! (16 min 51 sec)

NOTATAZ : 18/20 Test et approuv !

Les + : Bluetooth rapide, Puissant, Confortable, Double entres, Bonne finition, Bien quip .
Les - : Plastique PVC un peu "cheap" dans ce coloris ...

Les produits prsents sont visibles ici (en cliquant sur ces liens vous soutenez ma chane) Merci vous :

- Casque A70 sur (39) :
- Casque A70 sur site officiel :
- Site OneOdio Allemagne :

- TABLEAU DES PROMOS ET COUPONS BANGGOOD 2020 (remis jour rgulirement, pour aider la chane, gardez ce lien en favori ou...Continue Reading
Posted by Amanda BH | Jun 17, 2020 @ 04:44 AM | 7,764 Views
DRL BH Avenger 2510 1250kv
Posted by Tazkiller85 | Jun 17, 2020 @ 04:41 AM | 8,096 Views
Yep Les Amis,
Pas si BETA que a ! lol. J'ai en test aujourd'hui 2 produits de la gamme BETAFPV, la LiteRadio 2 et la camra Nano HD. Cette petite radio premier prix est plutt efficace malgr sa petite taille, elle sera parfaite pour ceux qui veulent s'initier au pilotage de racer et qui pourront aussi sentraner sur simulateur . Les gimballs ne sont pas ultra prcises mais elles font le job pour le prix. La petite camra Nano HD, mme si ce n'est pas la plus chre ni la plus performante du march, vous permettra, avec ses 6.71gr, de pouvoir quiper vos nano drone en HD. ... Bon Film Tous et Merci de votre soutien .

LiteRadio 2 et Nano HD Caméra BETAFPV - Review Test Démo Set Up - Mini Matos ! (31 min 2 sec)

NOTATAZ : Radio 17.5/20 Cam 16/20

Les produits prsents sont visibles ici (en cliquant sur ces liens vous soutenez ma chane) Merci vous :

- BETAFPV Nano HD Camra :
- BETAFPV Elite Radio 2 :
- Beta 65X :
- Rcepteur Jumper R1 :
- Dalprop Fold Series 5.1 :

- TABLEAU DES PROMOS ET COUPONS BANGGOOD 2020 (remis jour rgulirement, pour aider la chane, gardez ce lien en favori ou raccourci pour vos achats sur Banggood ) :

- Si Vous voulez aider la chane avec un don (tous les dons servent alimenter les vidos en produits ou matriel ):

...Continue Reading
Posted by Tazkiller85 | Jun 17, 2020 @ 04:40 AM | 8,010 Views
Yep Les Amis,
Bb BUMBLEBEE est n !!! Trop, trop mignon, ce petit cinwhoop DX40 m'a fait craquer par son design dans un premier temps. La mise en route t simple, et au premier dcollage, j'ai t agrablement surpris par sa stabilit en vol et la simplicit du pilotage en mode stabilis. Autre bonne surprise, aucun jello ni vibrations dans les images HD ! Le gros point ngatif c'est en 3S, les moteurs chauffent normment ( se brler les doigts), donc voir s'il est possible de modifier des rglages mais en attendant, en sortie de boite, je vous dconseille de voler en 3S. Malgr cela (et heureusement), il est suffisamment performant en 2S pour vous permettre de tourner de jolies cinmatiques en indoor ou en extrieur sans vent. En bref, c'est super petit joujou pour vous initier, vous perfectionner ou pour dvelopper vos talents de cinaste amateur ... Bon Film Tous et Merci de votre soutien .

HBFPV DX40 EVA Ducted - Review Test Démo - Un bébé Cinéwhoop HD !!! (16 min 54 sec)

NOTATAZ : 16.5/20 Pas mal mais...

Niveau : Dbutants / Confirms
Les + : Bien rgl sortie de boite, Original, Rsistant, Bonne camra, VTX ok, Images HD propres (pas de vibrations ni Jello ), Agrable piloter.
Les - : Pas adapt la 3S (dommage si vous n'avez que des 3S quand vous commandez ! ) , Sangle lipo faible ( 1 de plus ce serait bien ).

Les produits prsents sont visibles ici (en cliquant sur ces liens vous soutenez ma...Continue Reading
Posted by old4570 | Jun 16, 2020 @ 10:07 PM | 9,616 Views
SFB driver could have killed some one (0 min 52 sec)

Homicidal stupidity on the road ( almost )

No wind for the Super Cub (5 min 22 sec)
...Continue Reading