BetaFPV 550Mah LiHV 1S Lipo (4 min 52 sec)

Hello everyone welcome back.

In today's video I will be reviewing and showing you the new BetaFPV 550mah LiHV 1s Lipo batteries. These were sent over by BetaFPV so a huge thank you to BetaFPV. These are a step up from the Gaoneng 450 3.7v lipo batteries that I was using with the BetaFPV Beta 75. These batteries will give you a average of 5 minutes of flight time. In my testing I didn't notice any heat from the motors or battery. I was flying in 40-45 degree temperatures.

Here are the specs.

Capacity: 550mAh
Size: 16x7x64mm
Continuous Discharge Rate: 50/100C
Weight: 14.0g

Here is where you can get them.

http://amzn.to/2Edymsz

https://betafpv.com/products/550mah-...v-battery-2pcs

Check out my video on how to build and maintain your Tiny Whoop.

How to Build and Maintain your Tiny Whoop (35 min 33 sec)

...Continue Reading

716 Brushed Motor Thrust Testing. BetaFPV, Flight-Sky & GnarlyFPV (5 min 41 sec)

Hello everyone welcome back.

In today's video I will be doing some very crude motor and prop trust testing. In this video I will be pitting the BetaFPV, Flight-Sky and GnarlyFPV 716 brushed motors. In this test I used my homemade rig which consists of the motor mounts and ducts from a Beta 75 and a Beta 65s frame. I used standard 4 blade props for this test. Each test I used a fully charged LIHV 260mah BetaFPV battery. The motor was then cranked up to max in BetaFlight for a few seconds and the sustained pressure was measured.

The results were the following

BetaFPV - 8.4grams
Flight-Sky - 7.9grams
GnarlyFPV - 9.3grams

Here are the specs for each and where you can get them.

BetaFPV 716 17500kv Brushed Motor
Size: 7x16mm
Width:7mm
Height: 16mm
Cable length: 60mm
Shaft Diameter: 0.8mm
Weight: 2.9g (including cables and connector)
Speed: 17500kv or 56000RPM / 3.2V
Connector: JST 1.25mm 2P connector

http://amzn.to/2BnjlH4

Flight-Sky 716 17,500kv Brushed Motor
Size: 7x16mm
Width:7mm
Height: 16mm
Cable length: 60mm
Shaft Diameter: 0.8mm
Weight: 2.9g (including cables and connector)
Speed: 17500kv or 56000RPM / 3.2V
Connector: JST 1.25mm 2P connector

http://amzn.to/2z5slKQ

GnarlyFPV 716 Brushed Motor
Can size: 7x16mm
Shaft length : 5mm
Shaft diameter : 1mm
Wire length : 45mm
Plug - Micro JST 1.25
CW - Black Bottoms
CCW - Grey Bottoms
Operating Voltage - 2 - 4.35v

www.GnarlyFPV.com



Thank you very much for watching
Like, Share & Subscribe
Fly Safe & Fly Often

SolderSport FX805 AIO Camera (4 min 18 sec)

Hello everyone welcome back.

In today's video I will be showing you the SolderSport FX805 AIO Camera. This camera has great light handling along with nice reception. I am able to fly all over my house with little breakup. The camera case and reinforced antenna will protect the camera and keep you in the air after many crashes.

Here are the full specs
Transmitter power: 25mW
Input power: 2.5~5V
Camera resolution: 600TVL
Min illumination: 1 lux
Field of view: 140deg viewing angle
Antenna dimensions: 20 x 25mm diameter
Video output: NTSC
Frequency: 5.8GHz 5 bands 37 channels
Raceband: 5658-5917
Size: 21x19x17mm (excluding antenna)
Weight: 4.8g




Pick one up today
https://soldersport.com/


Check out my video on how to build and maintain your Tiny Whoop.

How to Build and Maintain your Tiny Whoop (35 min 33 sec)

...Continue Reading

GnarlyFPV's Blitz Spec motors The Fastest 716s on the Block (3 min 15 sec)

Hello everyone welcome back.

Today's video has me really excited. I have been on a mission to find faster 716 brushed motors. Well my mission is over. Thank you GnarlyFPV. These are the Blitz SPec motors. They are by far the fastest 716s I have flown. First launch sent me straight into the ceiling. That hasn't happened in a long time. I installed these motors into my BetaFPV Beta 65s. I also traded out my triblade props for some of their 4 blade props.

These motors are compatible with
Eachine E011
BoldClash Bwhoop
BetaFPV Beta 65s
JJRC H67
and any other micro quad that runs 716 motors.


Pick up some GnarlyFPV Bllitz Spec motors today
https://gnarlyfpv.com/collections/be...-game-changers



Check out my video on how to build and maintain your Tiny Whoop.

How to Build and Maintain your Tiny Whoop (35 min 33 sec)

...Continue Reading

Fly FPV? You need this Printer. The Monoprice Select Mini V2 3d Printer (7 min 3 sec)

Hello everyone welcome back!

Im really excited to show you all my new 3d printer. This is the Monoprice Select Mini V2. This is a fantastic budget 3d printer. I have been having a blast printing PLA, ABS and TPU all using stock Setup was a breeze. Out of the box I was able to level the bed and begin printing all in about 15 minutes!

Here are the full specs of the printer.

Model 21711
Extruder Type Single Extruder
Printing Technology FDM
Supported Filament Size 1.75mm
Supported Filament Types ABS, PLA
Max. Extruder Temperature +482°F (+250°C)
Max. Platform Temperature +140°F (+60°C)
Nozzle Diameter 0.4mm
Max. Printing Speed 55mm/sec
Layer Resolution Fast: 0.2mm, Normal: 0.131mm, High Quality: 0.087mm
Build Area 4.7" x 4.7" x 4.7" (120 x 120 x 120 mm)

Build Volume 103.8 cu-in (1728 cc)
Connectivity Wi-Fi®, microSD™ card, USB
Offline Printing Yes, with microSD™ card
Supported File Formats .stl and .obj
Supported Operating Systems Windows® 7 and later, Mac® OS X®
Supported Software Cura, Repetier-Host
Display Type 3.7" IPS color screen
Max. Power Consumption 120 watts
AC Adapter Input Power 100 ~ 240 VAC, 50/60 Hz
Input Power 12 VDC
Dimensions (H x W x D) 13.5" x 11.3 x 7.5" (343 x 287 x 190 mm)
Weight 9.9 lbs. (4.5 kg)


Pick one up today you will not regret it!
http://amzn.to/2BNMmrV

Definitely hit me up...Continue Reading