Posted by BDOG1 | Today @ 05:11 PM | 106 Views
Well finally got a chance to get out on the slope here in NY for some sloping.
I had missed 2 other chances when the conditions were better with the NW wind coming straight up the hill but 36 years of marriage have taught me
"Never miss taking your Wife out for her birthday "
Anyway : I have not been out on the slope since Wilson last spring so trying a West wind thru the hedgerow and across the face of the hill was worth a try...I Really Need a Fix

The Ka-8 let me down with no working ailerons so it was time to give the Demon a shot ,a gift from a friend I had only put one flight on it over flat land .

Life Is Good !
Posted by unboxingexp | Today @ 04:29 PM | 103 Views
For my budget TBS Source One build
Dimension: 70mm*30mm*2mm
Weight: about 5g
Material: Silicone
3M Silicone 2mm Thickness Non slip Mat Battery Anti skid (1 min 16 sec)

Posted by DutchRC | Today @ 12:06 PM | 349 Views
Halloa people

one of the essential tools for our hobby is a power / watt meter. At some point you will want to know what the Amp draw of your RC actually is.. Can you prop / gear up or not?

Link to this watt meter: ToolKitRC WM150 advanced Power analyser

And here is my show & tell of it

ToolKitRC - WM150 Advanced 150A Watt Meter - Show & Tell! (and GiveAway Announcement :)) (12 min 19 sec)

Posted by UnknownForces RC | Today @ 11:33 AM | 349 Views
Motor mounting plate of Ghost Rabbit GR1 (0 min 34 sec)

The first part of this video shows the CNC processing of an actuator disk for the diff lock of the Ghost Rabbit GR1. The part will be heat treated after the processing.

The second part of the video shows the motor mounting plate for the same car.
While most of its shape is processed on a CNC milling machine, the final steps of machining the bearing seats and some other surfaces which have all to be concentric are done on a CNC lathe.

A CNC milling machine is by design not capable of providing the same precision for these steps as a lathe. A lathe gives truly round and concentric results because the part itself rotates, not the tool.
A CNC milling machine makes a circle in many small steps, it interpolates the rounding. This is usually sufficient, but a lathe is clearly superior here.

Therefore we go the extra mile and use a lathe for these important steps of the processing. By doing so we achieve a precision for the bearing position of 0.005 mm."
Posted by kopterheld | Today @ 10:11 AM | 562 Views

The Nazgul5 is a very good freestyle drone that flies smooth as butter with 4S or 6S battery. The Stack is with F4 FC and 45A ESC's. The video transmitter is 25-600mW and at the front is the good CADDX Ratel FPV camera. The iFlight Xing-E 2207 2750KV motors are great even though they are entry-level motors.
6S - Coupon: BGnazgul
4S - Coupon: BGnazgul
oder 10% Coupon auf alles: BGBFAFF2019

Very good propellers are the HQProp Ethix S3 DP5.1X3.1X3
Amazon -
Banggood -

Runcam 5
Amazon -
Coupon: BGBFAFF2019 -
...Continue Reading
Posted by unboxingexp | Today @ 09:52 AM | 567 Views
Compact Fpv antenna, suits perfect my Fatshark Attitude 4. 2.5dbi, sufficient in most cases.
Foxeer 5.8G Lollipop 3 Stubby Omni FPV Antenna (1 min 22 sec)

Posted by unboxingexp | Today @ 09:51 AM | 569 Views
This one looks fresh!
Gain: 10dBi
Frequency Range: 5300-6000MHz
Beam Width: 90
Dimension: 40x40x5.2mm
Connector: SMA Male
Furious FPV Poker Chip FPV Antenna (1 min 28 sec)

Posted by unboxingexp | Today @ 09:50 AM | 568 Views
SMA Male To SMA Female to get the right angle for my FPV antennas on my Fatshark Attitude V5 goggles.
SMA Male To SMA Female 90° and 45° adapter (1 min 16 sec)

Posted by unboxingexp | Today @ 09:49 AM | 570 Views
Tiny but mighty! Checking Runcam's Nano 2 on a toothpick.
Image Sensor: 1/3" CMOS
Horizontal Resolution: 700TVL
Lens: 2.1mm(M8) FOV 155 1.8mm (M8) FOV 170
Signal System: NTSC / PAL
Current : [email protected] [email protected]
Housing Material: ABS
Net Weight: 3.2g
Runcam Nano 2 (1 min 16 sec)

Posted by unboxingexp | Today @ 09:48 AM | 570 Views
Here is comparison of video footage from Happymodel's Diamond VTX with DVR versus Fatshark's DVR on its Attitude V5. I definitely prefer the onboard footage...
Fatshark DVR vs onboard DVR (1 min 35 sec)

Posted by GroundControlRC | Today @ 08:59 AM | 572 Views

DustOff #7 - Glue & Fly Series F22 Micro V2 - 3S LIPO Fun Flight ;-)

Here is a link to the Video:

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #F22Micro

After several morning trips out to the area where I fly I finally had 5-6mph wind wihtout too much gust ;-)
Let's blow some Dust Off!

The skill level needed for this Parkjet is Intermediate to Advanced.
Intermediate setup is a 2S Power System with 10 points more Dual-Rate than on a 3S Setup.
Advanced setup is a 3S Power System.
It's very docile on a 2S Power System, Fast & Acrobatic with a 3S Power System.

The GFS F22 Micro V2 Plans are available for Patrons!

The GFS F22 Micro V1 Plans are available to Youtube Subscribers!
If you would like a copy of the Plans & Associated Documents send an email to [email protected]
In the Email Subject enter: GFS F22 Micro V1 Plans
We will get them to you as soon as we can.
You're going to love it ;-)

You Can Help Support Us By Using Our Affiliate Link To The Product Below. A small commission (At No Cost To You) helps us buy more items to review.

Here are links to the components:

Racerstar Racing Edition BR1407 3500KV 2-3S Brushless Motor

Emax ES9251Ⅱ Upgrade Version 2.5g Plastic Micro Digital Servo

TURNIGY Plush 10amp Speed Controller w/BEC

GemFan Bull Nose 3545 GRP/Nylon Propellers CW/CCW Set Green (2 pairs)

Turnigy nano-tech 460mah 2S 25~40C Lipo

Turnigy nano-tech 450mAh 3S 65C Lipo (E-flite Compatible Blade 180CFX EFLB4503SJ30)

OrangeRx R610V2 Lite DSM2 Compatible 6CH 2.4GHz Receiver w/CPPM (Version 2)

See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Consider Supporting Our Channel by becoming a Patron at:
Patrons of the Channel will have access to Exclusive Content!

See Us On Youtube | Patreon | RCGroups
Posted by old4570 | Today @ 08:33 AM | 597 Views
The motor only just bolts up to the test stand .

1s tests , I record thrust VIA the stand and RPM VIA the GT power tach .
2s tests are through the stand ...

I started with the smallest prop that would bolt to the motor , my 65mm prop .

1s - 65mm - 24,600 rpm for 42 grams of thrust
2s - 65mm - 36,000+ rpm for 108 grams of thrust ( motor is getting warm , but not so much as to burn ) 6.7A / 51W

The data sheet shows a 3020 prop

1s - 3020 - 19,000+ rpm for 46 grams of thrust
2s - 3020 - I was very gentle in adding power to see if the motor would cook ..
Around 2A the motor was starting to really warm up ...
I got brave and pushed the motor to 5A for only about two seconds and the motor got finger burning hot ...
No I didn't kill the motor , it lives !
But obviously 3020 is just too much for this motor with 2s ... ( I had to try as it's on the data sheet )
I would run that little 65mm prop 2s , or maybe a smaller 3 blade .. ( dont have any right now ) ...

Wow , 108 grams of thrust for a small 0905 ... Even 1s was not horrible ..
Posted by PittSpecial | Today @ 07:42 AM | 617 Views

To see the First Blog Post of this subject then, please go to:

UPDATE: (The KIT has been fully Assembled - FINISHED)

I have performed Weigh-In sessions and taken pictures of just the Dummy Engine "Hollow" Bust in two (2) configurations on the Digital Scale (oz.).

The first is including everything that came in the KIT and I assembled using and following 95% of the supplied instructions from Peter.

The other is leaving OUT the Metal Bolts & Nuts that came with the KIT and the Exhaust Pipe.
(Going to use Tie-Wraps to secure Engine Bust onto the Green three-point mount for weight savings!)

I have also included High Resolution "CLOSE-UP" Pictures of this KIT that was kindly shipped by Peter so, you can see the excellent results using the GORILLA "CLEAR" Glue. This Glue doesn't seem to have added any weight and the Title saying it is "CLEAR" is exactly that because you just can NOT see any residue of Glue anywhere!

Okay, the pictures showing what you have been waiting for (Sort of........).

Oh, as far as the mounting, I have a surprise in store and it will be my favorite thing I do with these models.

Stay Tuned!

...Continue Reading
Posted by kopterheld | Today @ 06:39 AM | 687 Views

The iFlight Titan DC5 is a 5 inch FPV freestyle drone with 222mm. The special thing about the drone is that it has the DJI Air Unit and can be flown with the DJI Digital goggles. The video image is digitally transmitted at 720p 120 frames per second to the goggles. At the same time, the video can be recorded in HD with 1080p 60 frames per second on the drone on a micro SD card. So you really do not need a GoPro camera anymore.

iFlight Titan DC5
6S - Coupon: BGBFAFF2019
4S Version -

...Continue Reading
Posted by phyngineer | Today @ 04:14 AM | 767 Views
Recently, Guangdong Power Grid Corporation Foshan Sanshui Power Supply Bureau completed the automatic cruise refinement inspection of all 10 kV overhead lines of Nanshan Power Supply Station and has applied refined routes to carry out daily inspections of double-light drones. Nanshan Power Supply Co., Ltd. became the first power supply company of Guangdong Power Grid Corporation to take the lead in realizing the full coverage of multi-sensor automatic cruise. At the same time, it also marks that the UAV has taken a new step in the application level of the distribution network and the level of refined inspection of the equipment.

Using the refined route to carry out "double light" drone automatic cruise

At the beginning of this year, the Guangdong Power Grid Company's aircraft patrol center selected Foshan Sanshui Power Supply Bureau as one of the pilot units for the patrol demonstration application of the drone. The bureau adopted the strategy of first pilot, post-standardization, re-copy, and promotion, and first selected Nanshan Power Supply as a pilot. The power supply area of ​​Nanshan Power Supply Station is 133 square kilometers, and there are 26 10 kilovolt lines in the power supply area. The total length of the line is 284.97 kilometers. The terrain and geology of the area are complex, the gully is vertical and horizontal, and the forest coverage rate is as high as 59%, which is a typical representative.

"Wangshan runs dead...Continue Reading
Posted by JENNIFERZHOU | Today @ 03:59 AM | 777 Views
Happy weekend,everyone!😌
🌾Weekend Sales🌾 is on going!
📢Purchase one of specific 3 racing drones and SQ001 electric Iron together can get $25 OFF now!
🛒Parrot132 PNP + SQ001 = 164.98USD 139.98USD
🛒Arrow3 PNP + SQ001 = 211.98USD 186.98USD
🛒Sector5 V2 PNP+ SQ001 = 236.98USD 211.98USD
Come and get this portable bundle for yourself ! Enjoy your weekend !😍😍😍
❗️BNF version is also available!
❗️VIew more here👉
Posted by DoubleEagle | Today @ 12:19 AM | 1,061 Views
Remote Control Speed Racer Car | Double E E325 Racer (0 min 59 sec)

Double Eagle Remote Control Toy Series
Posted by sanukiudon | Yesterday @ 09:09 PM | 1,369 Views
Posted by Reckless_fpv | Yesterday @ 06:32 PM | 1,601 Views