burkefj's blog View Details
Posted by burkefj | Sep 25, 2019 @ 11:18 AM | 1,039 Views
I have built this that I drew up many years ago in several versions, 6mm depron single ply with rocket in the rear, with tractor motor up front and air start rocket in the rear, in a doubled KF airfoil as both tail electric pusher and rocket glider(to stiffen the wings), I decided to build another one purely for rocket glider using some 9mm depron I have, allowing me to keep to single ply. I did a pseudo winter camo black/white eastern front scheme for fun. The problem with tail mounted motors in ME-163's are the moment arm of the tail to the CG is longer than to the nose so getting balance is a challenge. It came out a bit heavier than I wanted but still flies nice and is very docile on boost. As with any wing with CG shift as the motor burns out, the elevons don't have a lot of leverage in nose heavy condition and they can run out of flare on landing, but this one is pretty well balanced, not twitchy on boost and still nice to land.

25" long, 37" wingspan, 15.5 oz ready to fly using a 24mm longburn E-6 motor. I flew on E-12 motors but the boost is just faster but doesn't go quite as high.

Glide isn't terribly long, but this one was just for fun and looks good.

RC ME-163 Komet Rocket glider flying on 24mm E-6 rocket motors (2 min 2 sec)

Posted by burkefj | Jul 16, 2019 @ 12:38 PM | 2,953 Views
Here's one I designed and built/flew as an electric pusher and rocket glider in 6mm depron, this weekend I rebuilt one in 9mm which sacrificed some weight at the benefit of increased stiffness, flies great! 41" length, 25" wingspan, 15 oz rtf with 24mm E-6 and E-12 Aerotech rocket motors.

RC A-4B Winged V-2 rocket glider flight (0 min 49 sec)

Posted by burkefj | Jul 02, 2019 @ 05:37 PM | 2,980 Views
Not a Saab Draken, but I like the name and it was dragon themed with the logo....A new offering soon, 32" long, 25" wingspan, 10.5 oz rtf using 24mm E-6 motors and 2.6" diameter. I wanted something 1950's sci fi or steampunk sort of themed....

Dynasoar Rocketry Draken RC rocket glider kit E-6 flight (1 min 59 sec)

Posted by burkefj | May 07, 2019 @ 08:20 PM | 1,974 Views
I was asked by several folks to see if I could bring back my profile Dyna-soar kit I used to do as a rocket glider, due to the loss of true depron 6mm, the depron aero wasn't stiff enough to continue the kit and MPF was not uniform or stiff enough either. I was able to buy a supply of 9mm depron when rcfoam went out of business, so for a limited time I'm redoing the kit, calling it the Lifting Body, even though this is more of a small winged boosted glider than a true lifting body, it still fits the definition. Profile gets you maximium wing area, the 9mm is heavier but is definitely robust. Available from dynasoarrocketry.com

Here's a pic and video, 21" wingspan, 31" length, 14 oz rtf using a 24mm E-6 rocket motor. This is the same size as on the cover photo on top of the Titan II stack, but without a full fuse to make kitting/construction and flight times better. It can also be had with two other fuse/wingtip profiles to simulate X-24 or HL-10 styles

Lifting Body RC Rocket glider kit from Dynasoar Rocketry (1 min 9 sec)


Dynasoar Rocketry RC Lifting Body rocket glider kits, 3 styles to choose from! (3 min 5 sec)
...Continue Reading
Posted by burkefj | Mar 13, 2019 @ 10:22 AM | 5,823 Views
My daughter Olivia and I made the cover!
Posted by burkefj | Dec 13, 2018 @ 06:50 PM | 7,307 Views
Here's another I decided to kit. I figured my Iron Cross (Das Ugly stik) themed rocket glider needed a good guy to keep him in check. So I was inspired by the P-26 peashooter and inter-war us army air corps color schemes and here is the final product. 2.6" diameter, 34" long, 23" winspan and 11 oz rtf using a 24mm E-6 long burn motor.


Dynasoar Rocketry Peashooter RC Rocket glider flights (5 min 43 sec)

Posted by burkefj | Nov 22, 2018 @ 08:19 PM | 8,184 Views
Here are three new models that I did a while back but I decided to kit recently. First is the Mig 10 based roughly on the centuri mach 10 rocket glider and a mig-15, second is the UFO invader based on the old centuri UFO invader rocket kit but with the wing upsized for glide, and lastly the yf12 which was an interceptor prototype built for the u.s. air Force based on the SR-71 and A12 platforms used to do high-speed missile launch testing and then later by NASA. are designed for the excellent long burn 24 mm e6 rocket motor available online at dynasoarrocketry. com.
Posted by burkefj | Oct 13, 2018 @ 05:12 PM | 8,785 Views
I was watching The Man in the High Castle season 3 and that German SST design really got to me with the little forward and rear canards, the top mounted forward fin, and the paint scheme, so last night I designed and put this together and then this morning I painted and hand cut the vinyl trim and applied and it turned out pretty nice. I took a wing design I use on some of my kits, moved it forward to allow for the angle cut rear tube, and then trimmed the forward section down to be a bit more concorde like and reduce forward area to allow my CG to be the right place without having to add nose weight.


It's got a 23 inch wingspan, is 34 in Long, and11 oz rtf.

Disclaimer the swastikas are not any political statement they're just part of the paint scheme.

Man In the High Castle German SST RC Rocket Glider (2 min 49 sec)

Posted by burkefj | Oct 11, 2018 @ 06:32 PM | 8,179 Views
Here is another prototype for a custom kit, based on the old Estes Space Transporter America, which was a shuttle style rocket and had very small wings, so wings were upscaled, adjusted for CG, and upscaled to BT-80 size. The video shows the second flight first, the first flight is second and I over-adjusted on boost on this flight, and then adjusted the boost trim for the second flight which is a lot smoother. 38" long, 23" wingspan, 11 oz rtf using a 24mm E-6 long burn rocket motor.

Space Transporter America RC Rocket glider flights (3 min 21 sec)

Posted by burkefj | Oct 10, 2018 @ 09:34 AM | 7,981 Views
Here is the prototype for a custom kit I made for a customer, 34" long, 26" wingspan, 2" diameter, 10.5 oz rtf, Based on the Jonny Quest Dragonfly III, I lengthened the wing root and moved the wing/bottom scoop forward to have a reasonable CG, flew like a champ. Plenty of authority to flare and plop down on the grass and no issue with damage to the scoop. Sharpie fine line marker for panel lines, the canards are .03 styrene glued into slots in the nose cone I made with a dremel wheel, and the cockpit is shaped depron foam glued to the cone. Windows/glare shield is hand cut self adhesive vinyl. Elevon control and 24mm E-6 long burn rocket motor for boost.

Jonny Quest Dragonfly III RC Rocket glider (1 min 28 sec)

Posted by burkefj | Aug 25, 2018 @ 12:01 PM | 8,476 Views
Here's another fun kit I just released. It turned out that the biplane version turned out to be a bit more complicated to build and fly than I wanted but I still love this color scheme and styling, so I re-worked it.

The Iron Cross RC Rocket glider kit is based on a top secret WW1 Rocket powered mid wing monoplane interceptor. It has a graceful birdlike swept wing with scaloped trailing edges, a ww1 styled vertical stab, and an open cockpit. It comes with a plastic nose cone, 2.6″ white tubing for the body, Depron wing and 6mm depron tail surface. The wing is pre-grooved for the spar, control surfaces are pre-hinged, and the body tube is pre slotted for the vertical stab and partially slotted for the wing. Markings shown(not included) are available from Stickershock23.com 33″ long, 23″ wingspan, 10.75-11 oz rtf.(painted)

Dynasoar Rocketry Iron Cross RC Rocket Glider flight (1 min 54 sec)

Posted by burkefj | Aug 03, 2018 @ 10:29 AM | 8,590 Views
Here's a kit prototype I did themed on the Phil Kraft 1966 Das Ugly Stik, since it's a rocket glider with a tail mounted motor, I needed to have rear mounted wings for CG reasons, the first variation was a canard with kf airfoil which flew great but I built it without a kit in mind so my wingspan was too long and I had to slot the tubes for the wing/canard. A few customers really wanted a kit, so since I had to rebuild it to fit into a kit box anyway, reducing the span would make the glide shorter, so I decided to go with a staggered biplane design and get rid of the canard. This was my first biplane. With some planning the kit came out perfect with no nose weight needed. 11.5 oz, 23.5" wingspan, 32" length for my usual 24mm E-6 motors. I tried to keep the general tail and wing styling and the color scheme. On early testing I found I was getting wing flex without interwing struts which would make it hunt in pitch, I inserted two 3" wide struts and that fixed the problem. Painted with testors flat red and finished with cut vinyl decals from stickershock23.com.

My daughter had 10 minutes for a video in the morning, so I just did one flight, boost and landing were good, I did push over a bit early so it cost me about 10 or 15 seconds of glide time.

Dynasoar Rocketry Der RokitStik RC rocket gliding biplane (1 min 9 sec)

Posted by burkefj | Jun 25, 2018 @ 10:27 AM | 9,152 Views
I always thought the Centuri Skylab rocket from the early 70's was neat but never had one. Being left alone for the weekend my mindsim got the better of me and decided to do an RC rocket glider themed version.

I sat down and did some mass balancing Sims to convince myself weight and dimensions would work and the location if the wing and lateral stability, then looked in my parts drawer. I had some 2" tubing and 2.6". I picked up a bt20 nose cone pack and two white motor tubes for the tail thruster.

I thought styrofam coffee cups might work for the transition and nose and lo and behold the base of the cups were 2". I also found some small paper cups and they nested in the base of the foam cups to extend the nose. I doubled the foam cups for support and used a Depron disk in between them for stiffness and glued a coupler through the base for a shoulder. I doubled the cups for strength.

I'm using an 11" chord Depron wing with two carbon spars. Glide tests are done and it is looking good. I picked up some gold monokote trim for the wing/solar panels because I think it will look better than silver. It's 43" long and 27.5" span and 7.25 oz dry, rtf should be right around 12.5 oz , no nose weight was required. the RX and battery are mounted in the transition section.

I picked up some aluminum tube for rail button standoffs because the nose diameter is larger than the rear by 1/2". I put some skids on the bottom to make it level with the nose when landing.


Got the stickershock decals to finish off the skylab RC RG and got in some test flights today, was a bit more windy than I wanted and I had to keep the nose down into the headwind to keep it from balooning but overall not bad.

Skylab satellite themed RC Rocket glider (5 min 11 sec)

Posted by burkefj | Jun 22, 2018 @ 10:41 AM | 8,806 Views
One of my customers did this and it turned out pretty well. He sent some parts and here is my flight.

Dynasoar Rocketry Stratodart X Night Flight (1 min 36 sec)


The parts to do your own version and what I used are below:

Small gauge wire to make the jumpers to solder to the strips and connect + and – terminals from all the strips to each other. The strips can be connected from any set of pads since they are in parallel.

Red jst connector to fit the battery.

Lights

https://www.ebay.com/itm/LED-Strip-L…72.m2749.l2649

LED Strip Light SMD 3528 Flexible Tape 300led DC12V indoor outdoor lighting rope 5 meter length


Battery

https://hobbyking.com/en_us/turnigy-...pack-5pcs.html

Plan battery size, count your diides, current draw is 1 amp per 150 diodes(what I used), so with a 180mah battery using about 80 % of capacity to be safe would give 8 minutes, plenty long for pad wait, flight plus recovery.

I simply applied light strips to wing and fuse to make it easy to tell the difference between bottom and top and give light on the tail. I then used clear packing tape over the lights to protect them and hold them down.

On my stratodart I needed just a few grams of nose weight to rebalance. I left the 1s battery installed for receiver power and placed the small 3s battery for lights on the cg via a hatch. Battery weighs 19 grams so my starting weight was 11.6 oz without lights, with lights 12.2 oz, with 3s batt for night flight 12.9 oz. The stratodart has the most wing area and is able to carry the weight better.


For night flying, more is not necessarily better, you can blow out your night vision.


Here is my stratodart that I built using these parts.
Posted by burkefj | Jun 22, 2018 @ 10:28 AM | 8,769 Views
Here is an upscale of an old Estes kit. The original was a free flight glider and so to keep it stable on boost it swung the wing parallel to the fuse to move the CP rearward, and used a pop pod with extra fins that ejected at apogee to release the wing and put the glide CG back where it needed to be. I thought about doing one for a while, and did several simulations with wing folded and without.

With the wing folded and with a pop pod yielded about 75 more feet in altidude and about 1.5 ounce lighter glide weight, but at the cost of having to find the pod, I fly at a field that does not allow ejection of hot material from rocket gliders and the field is surrounded by tall crops.

With the wing folded but not using a pop pod, you also move the CP back, but then would need to put in some roll onto the elevons to counter assymetric drag, and add in the swing/release mechanism and you need to use a faster burning motor to be self stable, this yields about the same boost/glide weight, but with an optimized CG placement for less up trim required for glide and a bit more altitude.

With the wing fixed and steering on the way up yields a slightly reduced altitude but not as much as you think due to the slower burn motor/reduced speed/drag and a slightly shorter glide at the benefit of simplicity. That's the route I chose.

It's a 2.1" diameter, 28" wingspan, 11.4 ounce rtf model with a 10.2 ounce glide weight and about 13 ounce/sq foot wing loading with a .79sq foot wing, it doesn't glide that bad given the small wing area. Wing is 6mm depron reinforced with a .125 carbon spar, as is the horizontal stab and it uses just elevons for roll/pitch control.

2x upscale scissor wing transport RC Rocket glider flights (7 min 5 sec)

Posted by burkefj | Apr 23, 2018 @ 11:38 AM | 9,064 Views
I wanted to do something similar to the old Estes USS Atlantis, which was a long star trek themed rocket, I needed to keep weight in the rear at a minimum for a rocket glider so used one warp pod instead of two, and then did shapes as star-trekkie as I could, modified the nose to have the deflector dish inset.

35" long, 22" wingspan, 2.6" diameter, uses MPF for wings and depron for the vertical support with a carbon rod for strength. Weight is 12 oz rtf , Flights were perfect right off the drawing board with no trim changes,

NCC 2187 USS Forrestal RC Rocket glider Star Trek Inspired (1 min 21 sec)


USS Forrestal NCC 2187 Star Trek inspired RC Rocket Glider (1 min 17 sec)
...Continue Reading
Posted by burkefj | Apr 21, 2018 @ 11:49 AM | 9,304 Views
Here are three projects I did in parallel, the UFO Invader was themed on the old Centuri rocket kit, the Fireball XL-5 was as close as I could get while still having a decent glider and the Maurader is a top intake cruise missile styled model. All are around 10.5-12.5 oz rtf, use 2.6" tubing, and MPF and are 20" wingspans and 32-33" long.

Fireball XL-5 RC Rocket glider (1 min 31 sec)


UFO Invader RC rocket glider flight (1 min 37 sec)
...Continue Reading
Posted by burkefj | Apr 13, 2018 @ 11:02 AM | 9,219 Views
I did a torture test yesterday, 10 flights on E-20PW rocket motors, these give about a 150mph boost speed, and unless the glider is perfectly trimmed it would be a disaster since there is no time to steer I recommend the E-6 longburn motors since you get the same altitude at a bit less per flight cost and you have plenty of time to steer on the way up.

Dynasoar Rocketry HABU rocket glider, 10 flights on E-20PW motors (8 min 22 sec)

Posted by burkefj | Mar 31, 2018 @ 11:07 PM | 9,556 Views
I decided to work up a new kit version of my SR-71 profile I did a few years ago, to use a split tube above and below the fuse/wing profile and do tubes for the nacelles but just do them on the top to save tail weight. The SR-71 has very little of the nacelle below the wing line in any case. I worked with a local rc club mate to do some 3-d printed intake cones that have flow through, and some top and bottom pieces for the cockpit and battery access in the front. I've done three versions, an SR-71 version, an A-12 single cockpit CIA version where I used sharpie pen to make the wing corrugations and panel lines before spraying silver, and a one off version of a YF-12 interceptor. On the YF-12 instead of splitting the tube I slotted it so that the normal nose cone would fit into the tube, because of this the chines are a bit shorter than scale.

The first two kit runs are sold. 39" long, 21.5" wingspan, 13.25 oz rtf using a 24mm E-6 rocket motor. This kit is about 15% larger than the old hobbylab kit, with 33% more wing area at about the same flight weight. Instructions so you can see how it went together at: http://dynasoarrocketry.com/?page_id=1424

Some videos, the last video was an early prototype without markings, but that I was able to do two carrier type arrestor hook landings with

Dynasoar Rocketry HABU/A-12 rocket glider kit flights (2 min 59 sec)


RC YF-12 Rocket glider flight (1 min 20 sec)
...Continue Reading
Posted by burkefj | Feb 17, 2018 @ 11:18 AM | 10,146 Views
I had a receiver and set of servos my family got me for christmas and I decided I wanted to do something as a rocket glider but also to call back to my first aileron plane, a Kraft Das Ugly Stik(mine was actually a hobby shack electric stik version).

I decided that since it was a rocket plane, and a semi futuristic design, I'd use canard but keep the tail and wing shape a-la ugly stik.

I used a doubled kf airfoil wing and non movable canard and elevon controls, 27" wingspan, 30.5" length, 2.6" diameter. Weight all up rtf is 11 oz.

I've gotten pretty good at doing indoor test glides to figure out max rearward CG, however in this case, even with a good canard cg calculator in hand, I was pretty tail heavy. The first flight I should have called it der Bodenjäger because it was hunting the ground, not the Sky......

It didn't help I was maidening in a 10 mph wind that was blowing downwind toward the launcher...Off the rail it pitched forward into the exhaust trail obscuring it, and I tried to react, but it wound up doing three nice 50 foot loops about 10' off the ground at the bottom with no control input, and settling into a perfect landing in the field. This was due in large part to my piloting prowess and the luck of the Irish....

Deciding that either I got some inadvertent canard incidence or tail heaviness I added .3 oz nose weight and gave it another try. This time it boosted much better, I moved the launcher and myself so I was down wind...Continue Reading