FPV.Model's blog View Details
Archive for October, 2016
Posted by FPV.Model | Oct 31, 2016 @ 07:09 AM | 3,852 Views
Here comes two RC screw kits. They contain the most often needed screws for your multirotor build. Available in black and stainless steel finishes. No more bent, rusted or corroded screws.


Black: http://www.fpvmodel.com/black-carbon...kit_g1206.html


Stainless Steel: http://www.fpvmodel.com/stainless-st...kit_g1207.html

Each screw kit contains 360pcs Round Head screws and Flat Head Screws.

Round Head Screws ( 360pcs )
50pcs – M3 x 12 60pcs – M3 x 10
70pcs – M3 x 8 80pcs – M3 x 6
100pcs – M3 x 4

Flat Head Screws ( 360pcs )
50pcs – M3 x 12 60pcs – M3 x 10
70pcs – M3 x 8 80pcs – M3 x 6
100pcs – M3 x 4
Posted by FPV.Model | Oct 30, 2016 @ 05:51 AM | 3,770 Views
Coupon: Halloween
Discount: 9% oFF Entire store (X-Racer FC and Race Gates are not included)
Date: From now to November 1st.
Website: http://www.fpvmodel.com


Last two days for Halloween super sales. No tricks, just treats! Save 9% with your shopping at fpvmodel.com.

Simply enter code HALLOWEEN during the checkout procedure to get an extra 9% off our already keen prices. Please note the FPVModel RaceGates and the X-Racer flight controllers are excluded.


Posted by FPV.Model | Oct 28, 2016 @ 08:32 AM | 3,916 Views
Powerful allround motor, works great in the Blade Inductrix, Blade Nano QX, Blade CPX/S.

http://www.fpvmodel.com/6x15mm-corel...st-_g1212.html

Performance data:

speed: 14.000Kv
operating voltage: 1.5-3.7V
max. thrust: 15g (direct drive)
1.0A load current at 3.7V (direct drive)
lifetime rating: 5-6 hours

Dimensions:

can diameter: 6mm
can length: 15mm
shaft diameter: 0.8mm
shaft length: 5mm
weight: 1.8g
wire length: 70mm
plug: Micro-JST-1.25
To maximize performance and life span, dont run them in reverse!
(wire colors are reversed)



Posted by FPV.Model | Oct 27, 2016 @ 07:58 AM | 3,186 Views
The powerful DYS Fire 2600 racing motors are now available in stock. Available in 2100kv, 2300kv and 2600kv.

http://www.fpvmodel.com/dys-fire-220...tor_g1201.html

The DYS Fire are already proven winners on the race track, with team DYS took the 2nd place as sponsored team at Drone Worlds while using these motors.

It is the new stage of motor with 0.1mm laminations, Japanese ISC bearing and N54 magnets. More powerful for FPV racing and freedom flight. High efficiency for your race. Around 32g light weight with motor wire and M5 hollow shaft, 3-4s lipo support.



Posted by FPV.Model | Oct 25, 2016 @ 08:23 PM | 3,247 Views
FPV Model is having a yearly Halloween promotion. You can save 9% with all your purchases by using the coupon code HALLOWEEN at the checkout. These include the lastest Skyzone SKY02S V+ goggles. Save more than $40 USD for one set.

Discounted Price:
Whole set: US$407.60
Goggles only: US$366.80

This is a limited time offer, hurry whilst stocks last.

http://www.fpvmodel.com/skyzone-sky0...dvr_g1172.html


Posted by FPV.Model | Oct 23, 2016 @ 10:26 AM | 3,413 Views


A new batch of X-Racer F303 Flight Controller V3.1 has just arrived today. You can now order and enjoy the same day shipping.

The link: http://www.fpvmodel.com/x-racer-f303...ler_g1106.html

The newest version of the X-RACER F303 is Version 3.1. We have listened to your requests for SPI and weve went and changed the MPU 6050 over to MPU 6000 in order to give you those faster loop times that youve been asking for.

We've tried to keep the changes minimal with this and have left all of the previous changes that many requested the same. This board still comes with the through holes for Vbat, RSSI, and the buzzer. It also comes with the dedicated SBUS and RGB LED connections. X-Racer is designed for racers and acro pilots so we keep the desing simple and durable. Have fun with it!
Posted by FPV.Model | Oct 22, 2016 @ 06:56 AM | 3,763 Views
Designed to protect your Lipo battery when the battery is strapped to the bottom of your mini quad, suitable for KL200race, Alpha200 and many more. The battery protection plate comes with 7 different colors to meet your special requirement and make your mini quadcopeter stand out from the crowd.

http://www.fpvmodel.com/3d-printed-b...ors_g1193.html



...Continue Reading
Posted by FPV.Model | Oct 21, 2016 @ 10:23 AM | 3,292 Views
KL200Race Racing Quad
http://www.fpvmodel.com/kl200race-ra...ard_g1187.html

The KL200RACE is built for FPV racing. It features a light-weight, symmetrical carbon fiber body. The frame has been stripped down to the bare essentials yet maintain the strength and durability. The weight is only 82 grams including the PDB and included hardwares.

We are now taking the pre-orders of KL200race once again. The estimated shipping date is November 1st.

Specs & Features

4.0mm Main Frame
2.0mm Top Frame / 4.0mm Top Frame (Need to purchase seperately)
Aluminum Anodized & Stainless Steel Hardware
Light Shell with SMA Holder Combo
GoPro Mount
82 Grams only (Including Frame, PDB and Hardwares)



...Continue Reading
Posted by FPV.Model | Oct 20, 2016 @ 08:12 AM | 2,671 Views
The orange version of Foxeer Arrow V2 HS1190 looks cool.
http://www.fpvmodel.com/foxeer-arrow...osd_g1163.html


Posted by FPV.Model | Oct 19, 2016 @ 08:46 PM | 2,819 Views
FPV hobby is too expensive? Why not join our affiliate program to make extra money?

Check the details: http://www.fpvmodel.com/help_89.html

You do not need a website, do not need a store, do not actually sell the products. Making extra money is so easy with our affiliate program. What you need to do is to put the links of our products on your website, blog, social media, related RC forums, or anywhere else, then we will send you the commission on the sale that you have successfully refered.



Your commission will be calculated as a % of total effective orders that refered by your posted ads & links. The rate is based on your affiliate membership as shown in below table. Each membership has a different commission rate. The more the sale you made, the more the commission you will gain!



Join us and save your money on your build!
Posted by FPV.Model | Oct 18, 2016 @ 08:36 PM | 2,942 Views
Made this battery protective case that can be used with Fatshark goggles. This case is an extremely tight fitting design. The two halves fit together very tightly.

I‘ve also made a brief installation manual in PDF, you can find it out at http://www.fpvmodel.com/3d-printed-f...ase_g1209.html



Posted by FPV.Model | Oct 16, 2016 @ 06:47 AM | 6,688 Views
Something new from Matek Systems. Here comes the H-Type tail light with 8*WS2812B LEDs & Loud Buzzer. It provides dual control modes, can be controlled by Flight Controller fireware (Cleanflight, Betaflight, etc.) or Transmiter. Now we are taking pre-orders at fpvmodel.com.

Product: http://www.fpvmodel.com/matek-tail-l...des_g1208.html

Features & Spec.:

Dual modes: FC control & TX control
TX mode: LED 7 colors (White, Red, Green, Blue, Yellow, Magenta, Cyan)
LED 4 status (Constant light, Slow flash, Fast flash, Voilent flash)
Buzzer: Lost Plane Finder
FC mode: supports Naze32 & SPRacingF3 with CleanFlight or Betaflight firmware
Input voltage range: 4.5~5.2V DC
Power of TX mode (5V IN ): 1W/0.2A~2W/0.4A
Size & mounting: Please check the layout
Weight: 5 grams



...Continue Reading
Posted by FPV.Model | Oct 15, 2016 @ 08:01 AM | 2,442 Views


Time: Ends on Nov. 1st.
Coupon: Halloween
Store: http://www.fpvmodel.com

It’s time to grab yourself a bargain in our Haunted Halloween sale. Simply enter code HALLOWEEN during the checkout procedure to get an extra 9% off our already keen prices. Please note the FPVModel RaceGates and the X-Racer flight controllers are excluded.

Make sure you take a look at our Special Sale Section as well where you can combine the Halloween sale on items that are already marked way down! You can use the discount code on these items to get an even better deal. Save up to 65%!!!
Posted by FPV.Model | Oct 13, 2016 @ 10:46 PM | 2,578 Views
No need to worry about the damage to your motors, props and locknuts when removing them from your quad any more. The FPVModel Motor Grip Pliers are suitable for 2204, 2205, 2206, 2207, 1306, 1406 and 1806 sized motors, also the antennas and m5 motor lock nuts.

http://www.fpvmodel.com/fpvmodel-mot...els_g1200.html



Posted by FPV.Model | Oct 13, 2016 @ 08:18 AM | 2,229 Views
Congrats to our team pilot Ka Kei on the win at Hong Kong Drone Racing Championship 2016. This is a fantastic accomplishment!! Keep up the good work! Thank you to all pilots for your excellent performance.

Again, the frame KL200RACE from fpvmodel.com a proven winner.

KL200RACE: http://www.fpvmodel.com/kl200race-ra...ard_g1187.html

X-Racer F303 Flight Controller: http://www.fpvmodel.com/x-racer-f303...ler_g1106.html


Posted by FPV.Model | Oct 12, 2016 @ 09:52 PM | 2,235 Views
Material: Polyester Oxford 210D
Coating Width: 58"
Pole: 8mm Black FRP Pole
Width: 2.3m, Height: 1.63m. (For reference only, the size can be adjusted.)

We have had quite a few people asking for a more affordable gate that is less weight and easier to setup while having the same size opening as the other gates. These gates are meant for our more budget oriented custumers and will price easier to transport. They also feature the same style of eyelet of previous version FPVModel RaceGates for ensuring a strong setup for use of guide lines when it is windy outside.

Product: http://www.fpvmodel.com/new-fpvmodel...tes_g1121.html


Posted by FPV.Model | Oct 12, 2016 @ 08:00 AM | 2,058 Views
We've got a few newer designs we're working on but we also want to release a stackable PDB for those that may want to add to their flight controllers they already have.

So, we're working on an X-Racer Stack. Here's the quick question....what are the most wanted features you'd like to see in a stackable design for the X-Racer FC?

Please feel free to let us know your thoughts here or follow up the discussion at our FB page http://www.facebook.com/fpvmodel. Thank you all for your help to make the design better.
Posted by FPV.Model | Oct 11, 2016 @ 09:02 AM | 2,527 Views
Hello all, the new Skywalker EVE-2000 planes now are available in the stock. You can now order at fpvmodel.com and get the planes shipped the same day.



Besides, the WALL-E2000 will be available within one week. We are taking the pre-orders now.

EVE-2000 (In stock): http://www.fpvmodel.com/skywalker-ev...ane_g1191.html
WALL-E2000 (Pre-order): http://www.fpvmodel.com/skywalker-wa...ane_g1192.html
Posted by FPV.Model | Oct 10, 2016 @ 08:32 AM | 2,404 Views
So happy to see this survey in the facebook group Multirotors International, the X-Racer has got the most votes among the 30 listed Flight controllers. Thank you all for your trust.



The survey can be seen here: https://www.facebook.com/hashtag/mi_...55530354514609

X-Racer F303 Flight Controller: http://www.fpvmodel.com/x-racer-f303...ler_g1106.html


Posted by FPV.Model | Oct 09, 2016 @ 07:27 AM | 2,390 Views


* Japanese ISC bearing
* 0.1mm laminations
* N54 magnets
* M5 hollow shaft

Powerful and high efficiency, this is the new DYS FIRE FPV racing motor. It is the new stage of motor with 0.1mm laminations, Japanese ISC bearing and N54 magnets. More powerful for FPV racing and freedom flight. High efficiency for your race. Around 32g light weight with motor wire and M5 hollow shaft, 3-4s lipo support.

Buy DYS FIRE Racing Motor: http://www.fpvmodel.com/dys-fire-260...-cw_g1201.html


...Continue Reading