unboxingexp's blog View Details
Posted by unboxingexp | Sep 26, 2020 @ 11:00 AM | 2,650 Views
TS100 soldering iron (2 min 3 sec)

Posted by unboxingexp | Sep 10, 2020 @ 02:48 PM | 1,090 Views
Posted by unboxingexp | Sep 02, 2020 @ 11:03 AM | 3,202 Views
My new standard prop on my TBS Source One. The drone is way smaller so I can easily pack it in my backpack. For my flying skills the prop is good enough!
Dalprop Fold 5.1 folding propeller (3 min 7 sec)

Posted by unboxingexp | Aug 29, 2020 @ 11:03 AM | 7,919 Views
Took me some time to set the Beitian BN220 GPS sensor up. I made this video so you can save some time. It's awesome to have on your OSD data like speed , altitude and distance and direction to home. Love it!
Beitian BN220 GPS installation + test (1 min 47 sec)

Posted by unboxingexp | Aug 15, 2020 @ 11:19 AM | 3,181 Views
Happymodel Mobula6 HD unboxing + test (2 min 1 sec)

Here is another happy(model) Mobula 6 HD owner. Overall I was surprised by the HD footage I received from the onboard DVR. IMO there are only 2 major shortcomings: battery life is very short (below 2min on Gaoneng 350mAh) and some fail safes with Frsky D16.
Posted by unboxingexp | Jun 28, 2020 @ 05:24 AM | 5,352 Views
Posted by unboxingexp | Jun 24, 2020 @ 11:10 AM | 3,682 Views
I'm using this ultralight yet powerful Eachine Nano VTX on my 3inch whoop. I like the vtx but the Nano 3 cam I ve used is not well suited for outdoor flying.
Eachine Nano VTX (1 min 6 sec)

Posted by unboxingexp | Jun 22, 2020 @ 11:49 AM | 8,253 Views
Installed on a cheap E010 toy quadcopter.
Eachine TX06 (1 min 35 sec)

Posted by unboxingexp | Jun 20, 2020 @ 11:31 AM | 13,749 Views
My favorite battery for my brushless 65mm tinywhoop.
Gaoneng 1s 300mah (1 min 7 sec)

Posted by unboxingexp | Jun 04, 2020 @ 11:47 AM | 4,904 Views
Tinywhoop with micro HD camera (1 min 31 sec)

This is probably the cheapest way to get hd footage from your tiny whoop. I installed a 5$ sq11 camera on top. In order to save weight I decased it. Quality of the footage is still mediocre.
Posted by unboxingexp | May 06, 2020 @ 11:22 AM | 6,968 Views
Here are some tips and tricks to make your drone footage look more cinematic. I used my 3 inch cinewhoop in a forrest. All grading and editing was done with simple tools on iMovie.
How to give your drone footage that cinematic look (2 min 3 sec)

Posted by unboxingexp | May 02, 2020 @ 11:05 AM | 6,196 Views
No need to decase your Gopro! You can save 20 gram by simply powering your action cam over its USB port. You only need breadboard jumper wires, a USB step down module and an USB-C plug with PCB. My 3inch cinewhoop weighs only 236 gram with a Gopro Hero 7 black and a Tattu 4s 450mAh battery AUW! In this video it is shown how it's done! More details on the build are available as instructable here.
How to power a Gopro with Lipo balance plug (3 min 32 sec)

Posted by unboxingexp | May 01, 2020 @ 11:11 AM | 5,731 Views
1:24 RC excavator - Mofun 1022 (1 min 29 sec)

This small excavator is great fun. You can even move its bucket vis the remote controller. It's suited for in and outdoor use. Check it out!
Posted by unboxingexp | Apr 21, 2020 @ 03:00 PM | 9,317 Views
Flying Smiley (1 min 21 sec)

Posted by unboxingexp | Apr 20, 2020 @ 11:31 AM | 7,547 Views
Gemfan 3016 propeller (1 min 2 sec)

Low pitch 3 inch props for my ultralight cinewhoop build:
Blades: 3
Pitch: 1.6 inch
Material: PC
Center Hole Inner Diameter: 2mm/1.5mm
Prop disk diameter: 76.49mm
Center Thickness: 5.5mm
Max Prop width: 8.84mm
Adaptive motor: 1108-1303
Recommend motor: 1303-5000
Weight: 1.18g
Posted by unboxingexp | Apr 19, 2020 @ 11:48 AM | 3,847 Views
Flywoo Robo 1202.5 motors (1 min 12 sec)

Ultralight but powerfull! 5800kv for 2-4s setups. 2mm shaft for press fitting props like the Gemfan 3016. I'm using these motors on my ultralight cinewhoop.
Posted by unboxingexp | Apr 11, 2020 @ 11:01 AM | 7,348 Views
Here is another toothpick frame for up to 3inch props. I'm gonna use it in my ultralight cinewhoop.
Fonster Kpro 125 (1 min 4 sec)

Arm plate: 3mm
Other plate: 1.5mm
Material: Carbon Fiber + PLA
Camera adjustable: 57 degree
Weight: 17.6g (with printed part)
Recommend parts( Not Included):
Flight controller: Mounting size 25.5x25.5mm
Camera: 14.7x11.7x7.5mm, E7081
Motor: 9x12, 13xx 14xx
Posted by unboxingexp | Apr 09, 2020 @ 11:03 AM | 5,919 Views
For my ultralight cinewhoop project I used this ultralight AIO FC. I like it.
MAMBA F411AIO 13A (1 min 14 sec)

MCU: STM32 F411
SIX-AXIS: MPU6000
FLASH: NO
OSD: YES
BEC: 5V 1.5A
CURR:YES
INPUT: 2~4S Lipo (8.4V~16.8V)
CONTINUE CURRENT: 13A4
BURST CURRENT: 15A (10S)
SOFT: Dshot 300/600
MOUNTING: 25.5mm/M2
WEIGHT: 5.5g
Size:31.531.59mm