Posted by xixijoe | Today @ 10:15 AM | 66 Views
I have been flying bixler for around 6 years. as the hardwares and RC controller gets better and it flys further distance and more sofiticated system. I am planning to share all the steps of one of my bixler bulid here. I would like to share with whoever is flying same plane and would love to hear some advise if you can see anything can't be improve from my bulid of the bixler.

some of the bixlers have been crushed to nothing. while some of them I am still flying and some still in the middle of building. for the moment I can fly it for 90minutes with 60km above total distance with 4s 10000ma capacity. The FC control is F405wing and with split cam and servo gimble that can move in two direction. I printed some 3D parts in order to get better construction of adding cam, pitot,etc. I guess it could fly more distance if I can get best of set up on PID and some other stuff that I have been still wondering.
Posted by jmxp69 | Today @ 09:19 AM | 133 Views
I think I understand why T-28s are so popular at the club. They're cupcakes to fly:
Dynam T-28 Trojan RC Plane Maiden Flight (13 min 39 sec)

Posted by Laurence Carroll | Today @ 08:43 AM | 185 Views
Good grief this goes way back to when Dad was alive!!....since then we have moved a few times... now in Tokoroa back in the Nth Island....

Hard to believe whats happening now in the world and here with the Corona Virus as New Zealand goes into a complete lock down tomorrow night!!! To stop the spread of the virus hopefully, as we appear to have the first two community transmissions of it, so its Made in NZ now....

I have been checking here tonite for info on wood build F5J and F3 type sailplanes for DLG type flying.....I like the look of the Fresh F3 RES model

http://www.modellbauchaos.de/de/prod...es-modell.html

Our currency has taken a bit of a hit with the corona virus and is around 0.52 for both the USD and Euro.....sp will have to save up to buy the kitset from Germany and start the build....

So I must get back into adding more updates here for a start getting my new GepRC CineQueen 4K running and flyin in our back yard here.... Currently its got the Rx bound to my FlySky FS-i10 but is setting off an alarm on the control board. I think I need to chec it in Betaflight to see if I need to change some thing there. I have also the arming switch set up but the only seem to have partial throttle now... I may have to check with Brce on his XJet YT channel etc..... Laurie
Posted by RC Roundtable | Today @ 07:02 AM | 420 Views
Episode 103: "Caged Animals" is now live!
http://rcroundtable.com/podcasts/mp3...pisode_103.mp3

In this episode, we went live on video to talk about:
-Working from home (5:05)
-OSMW Mambo update (14:05)
-RC battleship (18:25)
-Glow fuel additives (24:45)
-Fitz goes live (33:55)
-Lee needs parts (38:50)
-Fitz's new MiG (1:11:05)
-Fitz saves (57:55)
-RCR in AMA mag (1:07:55)

You can visit our website at RCRoundtable.com to listen over the web or download an MP3 of the show. Or, you can subscribe to RC Roundtable on iTunes.
We would love to read your comments and ideas. Please drop us a line here, on twitter, or via email: [email protected].

You can visit our website at RCRoundtable.com to listen over the web or download an MP3 of the show. Or, you can subscribe to RC Roundtable on iTunes.

We would love to read your comments and ideas. Please drop us an email: [email protected].
Posted by Carmen Chen | Today @ 05:07 AM | 603 Views
Specification:
*Product size: 18.8*15*6.7 cm (fold) / 37.6*31.2*6.7 cm (unfold)
*Package size: 36.2*21.3*7.8cm
*Material: ABS
*Flying Time:20mins
*Charging time:5h
*Battery Type: Li-Po battery with a full capacity of 2800mAh/7.4V
*Cotrollling disrtance: About 500m *Video tranmission: 5G Wifi / 200-350m*Working Frequency: 5G+2.4G
*Camera Lens: drone 1080P HD camera (Adjustment)
*Brushless Gimbal
*Special Functions: Waypoint flight, Surround flight, Out of control return, GPS mode, Electronic fence, signal loss alarm, signal loss return, graded low power return, secondary low power electronic fence protection, Fixed altitude flight loss protection, multi-light function indication, independent GPS status indication


Feature:
1.1080P HD camera, 5G real-time transmission
2. Signal loss alarm, signal loss returns, no need to worry about signal interference
3. Built-in brushless motor with powerful power and speed
4. Altitude hold and GPS positioning function make flight more stable and safe
5. Surround flight and waypoint flight to make flying more fun
6. Out of control return, graded low power return to make the aircraft easier to recall
7.20 minutes long flight, long standby shooting
8. Secondary low-voltage electronic fence protection,
9. Electronic fence setting, so that the aircraft does not fly too far
10. Modular large capacity lithium battery, intelligent power management


Packing List:
Aircraft*1, controller*1, type-c charging cable*1,...Continue Reading
Posted by old4570 | Today @ 04:56 AM | 647 Views
Volantex Decathlon with big wheels (11 min 32 sec)



Big Wheels ...
Posted by Tokyo_Dom | Today @ 02:40 AM | 727 Views
I didnt actually realise the blog posts came out in a single thread like that. I should have made one post for each topic! (thanks Sakitume for pointing it out!)

So, this thread will detail my learning to fly FPV, and acro mode. I had previous experience with RC planes, so LOS is not so much of a problem, no matter which direction the quad is facing (an instructor back in my RC plane days once said "when the plane is facing towards you, and one wing dips, point the aileron stick in the direction of the dipped wing", not sure if this helps anyone, but its how i learnt to control planes coming towards me).

Anyway, my Little Pilot goggles havent arrived yet. I am still using the ROTG01 single antenna receiver, on an OTG cable on my phone. I did a rough latency check (point it at a stopwatch, and take a high shutter speed pic of the stopwatch and phone screen to see the difference in times shown) and it came in at 0.1s latency; that is apparently bad with reference to proper goggles/monitors, but seems ok for general flying - i am not good enough to fly super quick, and plus my reaction speed is slower than that.
Initially i figured this phone + OTG receiver + $5 phone VR goggles would be a good cheap FPV goggle replacement, but there is a reason those VR goggles are only $5. Major blurring and the view is not properly aligned for left/right eyes. I soon found that i had a better experience just putting my phone in a holder and watching it from that. Except i didnt have a holder, so i would just prop the phone up against a coffee cup or whatever. Great until you need to go pick up your quad from whatever predicament it has gotten into. Also meant i had to have a place to sit my phone when flying.

Despite my little pilot goggles being possibly only a few days away, i decided to buy a transmitter mounted phone holder just now....
Posted by GEMFAN ts | Today @ 02:09 AM | 744 Views
Feel no propwash and fast response.

Good throttle control especially slow and low, great for videography especially chasing subjects.

Extremely light with only 3.8g but durable enough compare same wight props.
Posted by stephenhughcrisp | Today @ 01:35 AM | 750 Views
Please help. I have the Taranis X9D Plus 2019 with Open TX 2.3.5. I have tried everything to bind with the S8R receiver. I have flashed the receiver with the latest software (tried both S8R_ACCST_V2.0.1FCC.frk and S8R_ACCST_V2.0.1_LBT.frk). Nothing works. Won't bind at all.
I would be grateful if someone could advise me.
Thank you
Posted by Thomas B | Today @ 12:28 AM | 855 Views
I have recently gotten more serious about a long planned collection of models.

I have been lucky enough to have a 34 year career (so far!) as a design engineer and model builder at Lockheed Martin in Fort Worth, TX, located in hiistoric Air Force Plant 4. When I started my career, the plant was General Dynamics.

My goal is to collect or build an RC example of every aircraft ever produced at Air Force Plant 4, plus a lot of the major and iconic Lockheed aircraft from the companies history.

Being a full time model builder for a LOT of years, I am not hung up on building each aircraft myself, at all. Particularly a lot of these, as I have been building models of them for a lot of years.....

Some are easy to acquire, some have to be scratch built. The eventual goal is to go to the field one day and fly the entire history of Air Force Plant 4, from the start to the present.

Starting with the first aircraft produced at the "bomber plant":

B-24 Liberator: I have a Flightline B-24.
B-32 Dominator: No kit or plans available in the size I want, which is about 80-84". This will a an original desgn, likely in
balsa, foam and vac form plastic.
B-36 Peacemaker: Current plan is to do one in. lightweight foam, rather like the one that Gary Jones did, possibly a
little larger, at about 72"
B-58 Hustler: Currently planning on building Keiths Spark's design from his Parkflyer...Continue Reading
Posted by alex_nikiforov | Yesterday @ 10:54 PM | 1,369 Views
Foxeer Micro Toothless Camera 1200TVL 5MP CMOS 1/2" Support OSD Remote Control FC for FPV RC Drone

Foxeer Toothless. Лучшая ФПВ камера 2020. (11 min 4 sec)


Link: Foxeer Micro Toothless
Posted by Space Goast | Yesterday @ 10:04 PM | 1,407 Views
Went out with a friend to fly a new spot. Tried to go as remote as we could, but lots of parks were closed thanks to COVID-19. Due to all the water and land it was also really bumpy. I managed to get a few minutes of decent footage, enjoy!
Social Distancing: FPV St Johns River (2 min 53 sec)

Posted by burkefj | Yesterday @ 08:16 PM | 1,549 Views
Here's a semi scale thunderchief I just completed. It uses 2.6 inch lightweight tubing, 6 mm depron surfaces and elevon controls. Wingspan is 26.5 in length is 34 in weight ready for liftoff is 11 oz.
F-105 Thunderchief R/C rocket glider flight (1 min 29 sec)
...Continue Reading
Posted by ww2collector | Yesterday @ 07:49 PM | 1,595 Views
I can't take full credit for the design. Found a similar scheme here on RCG. Trying to regain my Monokoting skills that I had in my youth.
Posted by DBSkyout | Yesterday @ 01:02 PM | 2,498 Views
I put this together to show what you can do with these amazing sailplanes. I did some retuning on my BAMF and it's really tracking in the turns. One of my favorite things to practice is javelin throwing into micro thermals and riding them out. Video work all on my Samsung S10 head mounted.
Riding Micro Thermals (4 min 56 sec)

Posted by NobatteryNopower | Yesterday @ 12:45 PM | 2,520 Views
Update!

Lots of stuff done, and encountered a small challenge on the way. The front window is distorting the view I already ordered 1mm plexiglass to conquer this horrible nightmare.

Body is almost completely painted. I am doubting if I should put on a semi-gloss clear coat for protecting the paint, or leave it as is and let nature do it's thing.
The hood didn't close properly. I chamfered the edges a bit and now it fits like a glove.
I've installed ultra bright led's for headlights, taken from a broken but high quality flashlight. This is going to be fun at night
Most windows are bolted to the frame, except the rear window. I think its a piece of lexan instead of perspex/acrylic. Very bendy and not too clear. To avoid glueing it in, as i might want to pop it out later for antennae or so, I took 1 mm styrene rod and made an internal frame. Now the window can be popped out the frame without too much trouble.

AND... I've managed to use a 7ch RX with PPM-out as input signal for my EzUhf No idea how I go from here. Maybe a long cable instead of this contraption works better in the end. But the idea of dropping the EzUhf on a roof, on a pole or hanging in a tree, to extend the range is an appealing idea. The Rx is 7ch, and my DX8 is, well 8ch. I have to test to see if the Rx is transmitting 7 or 8 PPM-channels. Edit***Well, maybe not:
Quote:
Originally Posted by schumixmd
Ok. meanwhile have checked how the PPM out works.

...Continue Reading
Posted by DutchRC | Yesterday @ 12:30 PM | 2,532 Views
Halloa peoples!

first of all: hope you're all safe & well.. and if not that you recover quickly..
with that out of the way: I've been testing this new orange cube for quite a while now, so it's time for my verdict I guess

Link to it: Runcam 5 Orange - 4K 30 fps Cube-style action camera


Runcam 5 Orange - Runcam's 2020 4K Action Cam for FPV :) (23 min 40 sec)



improvements:
+ 2 audio settings
+ Flat image style
+ higher bitrate
+ better battery management
+ 2.7K 60 fps (was 50fps before)
+ Image stabelization

Good:
+ pretty good bitrate
+ QR code app instead of WIFI
+ fits most Gopro Session mounts
+ inexpensive
+ light

downsides:
+ no ND filter
+ no 2.7K 30 fps
+ no WIFI
+ microUSB instead of USB-C
Posted by Jru28b | Yesterday @ 11:35 AM | 2,569 Views
Hi! Fairly new to this site, looking for some help.

Recently purchased a used Timber X from a friend. Had been crashed and was not flyable, so i took the elecs out and bought new wings, fuse, stabs. Put every single servo in the new plane the exact same way, centered them on a tester, all that good stuff. Didn't have any issues until i tried to bind yesterday. New file in my DX9, all the channel inputs are set up right, everything was set up exactly as it was supposed to be according to the manual. The tail servos were fine but all four wing servos are way off. Either maxed out up or down. Everything, trims, sub-trims, all that is zeroed and never been adjusted. Tried putting a 9030T receiver in it to eliminate Y-harnesses. Same exact thing. One flap and one aileron are completely backwards, and frying the servos trying to overextend. So i took the wings off, all servos at zero plugged into the RX, centered the arms and tried again. Same thing again. They return to way off, and twitch every couple seconds. A 9030 doesn't have SAFE or AS3X obviously, so there's no gyro that needs to be calibrated or reset or something. What am I doing wrong?
Posted by mundirman | Yesterday @ 10:11 AM | 2,693 Views
Day 2, lockdown Covid-19 at RG38 Airfield

Helipad RG38 Airfield - Sebulu, 22 Maret 2020 (11 min 48 sec)

Posted by old4570 | Yesterday @ 06:09 AM | 3,475 Views
Coronavirus: Victoria in lockdown within next 48 hours | Nine News Australia (9 min 0 sec)



Apparently , too many Australians are ( Insert something insensitive )

Who would have guessed ?