Posted by jmxp69 | Today @ 12:34 PM | 240 Views
I received some radios to review. This is the first look video covering three radios in the Detrum line-up along with a handful of receivers, stabilizers, and flight controllers.

First Look - Blitz DT-9, Gavin 6A and 6C, and more... (28 min 46 sec)

Posted by JureZ | Yesterday @ 07:42 PM | 1,089 Views
here is one more for the collection of Frankenplanes

AUW 990g ,Wing Span 44" , Propeller MAS 10x8 , Motor BL15 , Battery 3S 40C 2200 mAh

Frankenstein Extra Trojan T 28 Movie (2 min 24 sec)

Posted by GBLynden | Yesterday @ 06:40 PM | 1,142 Views
This is my unboxing for my new E-flite F-15 Eagle 64mm EDF Jet.

E-flite F-15 Eagle 64mm EDF Jet With AS3X & SAFE Select Unboxing (8 min 2 sec)

Review Notes for this Beginner EDF Jet:

- The paint scheme is nice and colorful
- It comes BNF Basic with very little setup required
- It is a RC Smart Jet thanks to optional SAFE Select
- Flies on popular 4S 2200’s. Some say it will fly on smaller packs just fine too.

- You have to glue it
- Poor turning radius
- No rudders
Posted by drewdb | Yesterday @ 04:26 PM | 1,339 Views
Better late than never. Thanks to Nagas for pointing this out.

I use to contribute 3D models to the Phoenix thread on here and here's a render of the best of what I produced during that time.

Now that I know I have this will have to add more later.
Posted by Mad_angler1 | Yesterday @ 02:50 PM | 1,506 Views
Prowler Rover Ardupilot Build

I am in the process of building a Ardupilot based rover on my channel and here I will also post the videos as well as some of the other issues and progress I make on this project.


ServoCity Prowler Rover Chassie
Dimension Engineering Sabertooth 2x32 DC Motor Controller
ProfiCNC/Hex Aero Cube Purple Autopilot
ProfiCNC/Hex Aero Herelink FPV RC System
GoPro Hero 7 Camera System
TFmini Plus Range Finder

Prowler Build Video Pt 1

New Prowler ArduRover Build Series - Pt1 Intro (2 min 54 sec)

Prowler Build Video Pt 2

...Continue Reading
Posted by Mad_angler1 | Yesterday @ 02:35 PM | 1,466 Views
Below is all of my review and how-too videos on the DJI Digital FPV system, I will continue to update this as more are published.

Review Overview

DJI Digital FPV System - Complete Overview & Menu Walk Though (23 min 51 sec)


DJI Digital FPV System Force FCC Mode Hack

DJI Digital FPV System Force FCC Mode Hack (5 min 10 sec)
...Continue Reading
Posted by RCRT2018 | Yesterday @ 01:53 PM | 1,467 Views
So I am new to this, so be easy with me. I have a Carbon Z 150 and was given a brand new Hitec camera. I would like to attach it to the airplane. I am just curious from one's that have done it. Where is the best place to mou t it and do I need to do anything special? Thanks in advance
Posted by jmxp69 | Yesterday @ 12:47 PM | 1,500 Views
Ever get the feeling you should put the transmitter down and go sit in the peanut gallery the rest of the day?

How to NOT Fly Your RC Plane (10 min 49 sec)

Posted by DutchRC | Yesterday @ 12:11 PM | 1,590 Views
Halloa people

obviously OpenTX radio's are very popular because of their "flexibility".. you can make them do all kinds of things I recently heard someone say he had a hard time Feeling the center-position of a slider.. Depends on the radio ofcourse BUT.. You can add audible feedback

How?? In this short how-to I will show you...

OpenTX How-To - Center Alert Sound for sholder-slider / rotary knobs (12 min 57 sec)

Posted by slopok | Yesterday @ 07:50 AM | 1,739 Views

I've had to use this in the past about not receiving an item. It worked for me. An officer from his town contacted me. I sent all emails, private messages, photos and contact info that I was given. I got my item back but not the money order. The item came from a different address. I contacted the officer and gave him the other address.
Posted by nagas | Yesterday @ 04:48 AM | 2,102 Views
After the successful Phoenix CH-53 Stallion models, Rick was looking for the next copter to make and so I suggested the Sikorsky S-97 Raider. While Rick developed the model in Blender, I was working on the flight capabilities in Builder so a great collaboration. It has been a pleasure, thanks for the honour of working with you Rick and of posting the finished models.

Phoenix Models

Three versions are available for download here:

1) Sikorsky Raider Prototype P1 with side mounted gun pod and rockets.

2) Canadian Search and Rescue (SAR) with drop tanks.

3) Indian Air Force Sarang Demonstration Team.

The Sikorsky S-97 Raider is a high-speed scout and attack compound helicopter (main rotors and pusher prop) with a coaxial rotor system under development by Sikorsky Aircraft. Sikorsky planned to offer it for the United States Army's Armed Aerial Scout program, along with other possible uses including civilian applications such as Search and Rescue.

The S-97 made its maiden flight on 22 May 2015 and is a continuation of the experimental coaxial S-69 from the 1970s and the more recent X2 technology demonstrator of 2010. Construction of two prototypes began in October 2012, the first prototype (P1) was revealed in 2014 and has been used for flight testing while the second (P2) is for use as a demonstrator. The S-97 Raider is wholly funded by private investment with Sikorsky providing 75 percent of the costs and 53 principal suppliers providing the rest.

...Continue Reading
Posted by CarreraGTSCS | Dec 07, 2019 @ 08:45 PM | 2,372 Views
Sopwith Pup Video #2 (5 min 3 sec)

Posted by old4570 | Dec 07, 2019 @ 04:48 PM | 2,722 Views
Swallow 800 (7 min 37 sec)

Rolled out of bed about 5.45am and walked out the door about 6.05am ( Sunday Morning )

So much wind this year .. Sunday morning is the only low wind time in about a week .

Swallow 800 > Mistakes !

I used 4.3g servos , dont bother ! Just use 9g servos .. When you glue the wing ( foam bits ) it is already very close to achieving CG . So when you pile in your hardware , your shifting that CG forward ..
I used some screws on the wing tips to get CG ,

I mentioned in a earlier post that the foam is soft , and the wing is easy to warp .

Flying the Swallow 800 ( NX3 gyro is off )

Needed a lot of trim to counter warping ( mild warp ) , but still !
My CG is as close as I can get to recommended , where the motor mounts to the model .
Ailerons are soft , really soft . You want decent length servo arms ( like with a 9g servo ) for more throw .
Elevator is ok , but that soft wing needs Aileron authority . Especially at the low speeds I was flying at .
I really need more aileron , and maybe I have to pull out those small servos and do a 9g transplant .

This thing is draggy ! The 1306 was @ about 1/3 throttle most of the time and it flew slow .
I think properly set up , this wing would be seriously NOOB friendly .
Being so soft how ever , you probably dont want to crash it . But , it's also relatively cheap . Selling under $20 USD for the kit at the moment .

If I built another ?

Definitely use some 9g servos .
Maybe a larger motor like a 1806 ( Maybe ) and a 5x5x3 prop ( Maybe )
Posted by DutchRC | Dec 07, 2019 @ 12:14 PM | 3,321 Views
Halloa peoples

soo maybe you've been wanting to Try the FPV thing, but you're not sure what a good starter package would be..
In this video I'll tell you what IS a nice set, and what isn't.....

THE FPV Starter Kit ? Getting Started in FPV (10 min 1 sec)

Posted by Ozyris | Dec 07, 2019 @ 10:42 AM | 3,397 Views
Posted by TMacFPV | Dec 07, 2019 @ 09:23 AM | 3,499 Views
Jumper T16 complete telemetry setup (including Betaflight & custom voice warnings) with Jumper R1 full range telemetry receiver. Side-by-side RSSI flight comparison with FrSky R-XSR receiver. Can this less-expensive Jumper R1 compete with the FrSky R-XSR?

Posted by Tazkiller85 | Dec 07, 2019 @ 06:05 AM | 3,772 Views
Yep Les Amis,
Comme ça c'est clair ! lol ... Vu que la météo n'est pas très clémente en ce moment, j'en profite pour vous informer de quelques détails importants pour moi et quelques nouveautés par la même occasion . Bon Film et Bon WE à Tous ...

Vidéo spéciale abonnés - Prévisions / Concours / Annonce etc ... (12 min 55 sec)

- TOUTES LES PROMOS ET COUPONS BANGGOOD 2019 (remis à jour régulièrement, gardez ce lien en favori ou raccourci pour vos achats sur Banggood ) :

- Si Vous voulez aider la chaîne avec un don (tous les dons servent à alimenter les vidéos en produits ou matériel ):

- Frame Mr Croc FLYWOO :
- Eachine Tyro89 :
- Wltoys 144001 1/14 :
- Eachine EMAX EAT03 :
- Eachine EX4 :

Mon matériel ( je recommande bien sur ) :
- Radio Nirvana NV-14 :
- Jumper T8SG V2.0 Plus Carbon :
- Skyzone SKY03O Oled ( promo 384€):
- Masque FXT VIPER :
- DJI OSMO ACTION ( coupon BGOCT1 ) :
- Caméra Casquette Firefly 8SE :
- Micro cravate (casquette FF8SE ):
- Stabilisateur smartphone :
- Chargeur ISDT D2 :
- Chargeur AOKoda 1S : https:/...Continue Reading
Posted by Tazkiller85 | Dec 07, 2019 @ 06:04 AM | 3,760 Views
Yep Les Amis,
Le Racer 1S SURVITAMINÉ !!! Quand j'ai reçu ce Tinywhoop, je me suis dit "encore un engin basique, faiblard et fragile à tester " ! La mise en route terminée, j'enfile les lunettes et je décolle dans mon salon ... WHAOOOOOOWW !!!! En premier lieu je suis surpris de la puissance et un peu effrayé, je me dis que je vais très vite l'exploser conte un mur. Puis, je suis encore plus surpris par sa réactivité et sa maniabilité. Très vite j'ai pris confiance et à mon grand étonnement, j'ai atteins des vitesses folles dans ma petite maison en ne touchant que très rarement les murs ou meubles. Pour résumer, ce Meteor65 porte vraiment bien son nom, c'est une vrai bombe pour un Tiny 1S. Des moteurs 22000KV, un poids ridicule et la nouvelle connectique BT2.0, font de cet appareil, l'engin IDÉAL pour les pilotes expérimentés en recherche de sensations fortes . Bon Vol à Tous !

Meteor65 BetaFPV - Review Test Démo - Puissance et Précision ! (21 min 40 sec)

NOTATAZ : 17/20 Il porte bien son nom !

Niveau : Confirmés
Les + : Très rapide, Très réactif, Bonne portée, Bonne config, Réglage d'origine OK, Caméra correcte, Innovant.
Les - : Canopée fragile, Faible autonomie, Hélice s'éjectent sur gros chocs ...

- Si Vous voulez aider la chaîne avec un don (tous les dons servent à alimenter les vidéos en produits ou matériel ):

Les produits présentés sont visibles ici (en cliquant sur ces...Continue Reading