Posted by Bill M - RC | Today @ 04:42 PM | 527 Views
Hi fellow rc pilots & rc enthusiasts

Eachine Mini Mustang P-51D review. In this Eachine Mini Mustang P-51D RTF Airplane review, I include unboxing, functions, setup, flight & duration tests.

Get this Eachine Mini Mustang EPP 400mm Wingspan 2.4G 6-Axis Gyro RC Airplane Trainer Fixed Wing RTF One Key Return for Beginners here now: http://bit.ly/2RO6eUt

Eachine Mini Mustang P-51D RTF Airplane review - Great trainer for beginners (24 min 25 sec)

Posted by GroundControlRC | Today @ 08:09 AM | 1,777 Views
Sneak Peek on my Build Progress of the MinimumRC B-25 Mitchell Part 2

Here is a link to this Plane:
https://www.minimumrc.com/b25-mitchell-p0082.html

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #MinimumRC #B25Michell #B25 #Bomber

This Plane is Courtesy of MinimumRC!
@minimumrcplanes

I have the fuselage complete with the attached landing struts.
The horizontal stabilizer and vertical stabilizers are glued in.
The wings and the nacelles are just dry fitted before gluing.
The wheels are on the axels but are not secured.
I have to glue in the wing spars, wings, nacelles, secure the wheels, and the airframe will be complete.
With a bit of luck, and time, I should have the Airframe completed tonight.

See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Ground Control RC™ Glue & Fly™ Series Scratch-Build Planes

Consider Supporting Our Channel by becoming a Patron at: https://www.patreon.com/groundcontrolrc
Patrons of the Channel will have access to the latest Aircraft Plans & Exclusive Content!

See Us On Youtube | Patreon | RCGroups

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
Posted by GroundControlRC | Today @ 08:04 AM | 1,797 Views


Test Flight #1 - Eachine Mini Mustang P51D RTF - Elevator Adjustment

Here is a link to the Video:
https://www.youtube.com/watch?v=TiuUcTiVn-A

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #Eachine #MiniMustang #P51D

This Aircraft is courtesy of Banggood!

Eachine Mini Mustang P-51D RTF
https://www.banggood.com/custlink/vvmDAdvdjk

The Elevator on this Plane is just a bit too sensitive in Manual Mode.
I managed to remove the Elevator Control Rod and move it from the Control Horn center hole and relocate it to the Control Horn bottom hole.
This made the Elevator much less sensitive and certainly made it easier to fly in Manual Mode ;-)
I'm pretty happy with this Plane now.

You Can Help Support Us By Using Our Affiliate Link To The Product Below. A small commission (At No Cost To You) helps us buy more items to review.

Eachine Mini Mustang P-51D RTF
https://www.banggood.com/custlink/vvmDAdvdjk

Spare Parts:

Lipo Battery 1S 360mAh for Eachine Mini Mustang P-51D RC Airplane
https://www.banggood.com/3_7V-360mAh...47791920140372

Brushed Motor 10mm Hollow Cup for Eachine Mini Mustang P-51D RC Airplane
https://www.banggood.com/10mm-Hollow...47791920140372

Prop 130X70mm Propeller Set for Eachine Mini Mustang P-51D RC Airplane
https://www.banggood.com/130X70mm-Pr...47791920140372

Gearbox for Eachine Mini Mustang P-51D RC Airplane
https://www.banggood.com/Gearbox-for...47791920140372

Receiver Board Original 4 CH Onboard Servo for Eachine Mini Mustang P-51D RC Airplane
https://www.banggood.com/Original-4-...47791920140372

Front Landing Gear Set for Eachine Mini Mustang P-51D RC Airplane
https://www.banggood.com/Front-Landi...47791920140372

Eachine Mini Mustang P-51D RC Airplane Push Rod Set
https://www.banggood.com/Eachine-Min...47791920140372

2PCS Eachine Mini Mustang P-51D RC Airplane Spare Part Rudder Angle
https://www.banggood.com/2PCS-Eachin...47791920140372


See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Ground Control RC™ Glue & Fly™ Series Scratch-Build Planes

Consider Supporting Our Channel by becoming a Patron at: https://www.patreon.com/groundcontrolrc
Patrons of the Channel will have access to the latest Aircraft Plans & Exclusive Content!

See Us On Youtube | Patreon | RCGroups

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
Posted by old4570 | Today @ 07:27 AM | 1,931 Views
XK A600 , gone in 60 seconds . (1 min 4 sec)


I seem to have found a serious problem ..
Playing with the XK A600 after repairs and watching this video ..
It would seem that the XK A600 kicks in left rudder when the plane is in certain orientation ..

One second I am fighting to keep control and the next it is flying ok , then suddenly it goes weird on me again .
I can only put it down to the plane suddenly kicking in full left rudder for some reason .

WOW ! So my last 4 planes have been horribly disappointing .

DLG glider with a warped wing .
Decathlon
XK A600
and a Stagger Wing biplane that was killed for exactly the same cause as my DLG ( Hard left turn built in )
Damn ..
Out of 6 new planes , 4 have been bad to terrible .

Back to the XK A600 ..
Perhaps part of the problem is that XK may have used a helicopter flight board ... (?)
Do we really need a gyro on the rudder ?
I have no choice , I have had to unplug the rudder servo ..

The XK A800 did fly like a normal RC plane , well a little bit ! The rest of the time I was fighting to keep it away from terrafirma .
Yeah , well the XK A600 Won in the end and it slammed the ground hard enough to break the wing .

Next outing !
No rudder , and a little bit of lead in the nose ..
Posted by jmxp69 | Today @ 12:31 AM | 2,838 Views
This was about as easy as it gets:

Dynam Focke Wulf FW 190 Build Review (7 min 3 sec)

Posted by kuhlrunner | Yesterday @ 08:43 PM | 1,767 Views
This is a copy of the post I recently added to the Micro EDF Jets and Power Systems forum.

Hey y'all,

I'm new to the RCGroups community, and the hobby in general, but I've always been impressed by other people posting about their great builds and fun ideas they try out. I'm especially inspired by FliteTest and everything they and their great community has put out to help people get into the hobby.

I've been flying a HobbyZone Super Cub (the old version) that I was given by some relatives... after the tail had been smashed. I fixed up the tail control surfaces with some foam board and it's been working well. I've finally got the inspiration to build a plane of my own... an indoor micro 25mm EDF jet!

So far, I've found and scaled down some community-generated plans for an Aero L-39 Albatros model (thanks Grifflyer!) and created a scratch-built EDF power system with a total diameter of 25mm. I'm using an old mini-quad brushed inrunner motor and clipped propeller, some 3d-printed parts, and a bit of thin (PVC?) pipe. I'm not sure what thrust it provides, or how to figure that out, but it has a nice kick to it when I hook it up to a 300mah 7.4v battery. Here's some pictures...

Name: IMG_2347.jpg
Views: 0
Size: 1.28 MB
Description:
Name: IMG_2351.jpg
Views: 0
Size: 1.01 MB
Description:
...Continue Reading
Posted by old4570 | Yesterday @ 07:32 PM | 3,371 Views
OMPHobby T720 RTF (12 min 25 sec)


I purchased a second hand T720 from a well know modeller ..
And having watched his video's I noted something of interest , he was flying and lost an aileron .

Long story short , that T720 ended up being for sale ! Yeah , can you guess who got it ? ..

Anyways !

I remembered that tit bit from the video !
Assembling the T720 , I checked the wings !
And found the right wing rocked back and forth enough for the control lever in the fuse to pop out of the aileron slot !
On close examination , the PLASTIC spar was broken ( See Pictures ) ..
From the way it was broken ( direction ) , I would hazard a guess it may have occurred when the wings were pulled out of the fuse or ............
If the T720 hit the ground and the wing popped out and then force was put on the spar when the wing was hanging lose ...
It's all speculation !

I hit the break with some cyno and it looked to hold well . To add strength I cut some inserts and glued them inside the spar for added strength top and bottom , .... See Pictures .

I like the modular design !
Unfortunately , every last video review I have seen :
The wings or elevators pop off on landing .
I don't think I have seen a single video where this did not happen ..

Anyways , hopefully a simple repair and a functioning toy .
Posted by jmxp69 | Yesterday @ 06:58 PM | 3,410 Views
This is a first look video at the Dynam Focke Wulf FW-190:
Dynam Focke Wulf FW 190 First Look (10 min 52 sec)

Posted by VicT | Yesterday @ 04:51 PM | 3,705 Views
I got to program a DX6 and maiden a clubmember’s new Somethin Extra. With the Rimfire 46 and 12/6 prop and 5S she goes vertical and rolls fast and symmetrical. Nice big loops and knife edges OK. Power off glide is long and faster than flapped models but is OK if you have the landing space. No aileron to rudder mix is needed. She needed just a little aileron and rudder trim then I set up wireless buddy box training for the owner. After about 5 minutes we ended up with ailerons on 30 percent. He has been used to flying an Eflite Commander with SAFE On. An AR 636 programmed to the Extra 300 3D specs will replace the antenna less AR620 receiver. My 4 ch version works great with RSSI telemetry but I could not get his to work and Horizon Hobby Technical phone support did not work.

The battery holder and prop spinner was not used. When I put the spinner on there was vibration at half power so it was removed. An Aluminum will be searched for. The 5S had 35 percent remaining after 3 flights so I figure it’s good for at least 9 minutes. More buddy box flying for familiarization is planned. Owner is still getting used to electric over glow power. Anyone recommend an under $100 sound system?
Posted by DutchRC | Yesterday @ 12:54 PM | 3,977 Views
Halloa RC pilots

last year ZOHD released it's Kopilot Lite stabelizer package and by no I actually have Two of them (the ZOHD Dart also came with one).. In this thread I will take you on a tour of my experiences with this setup.. It should be easy to install & use.. We will see!

Link to the set: ZOHD Kopilot Lite stabelizer + GPS

In this series I will be using a ZOHD Nano Talon Evo to test it in, but I could have used most other planes..

First my how-to-install the thing.. as detailed as possible..

ZOHD Airplace Kopilot Lite with GPS - HOW TO INSTALL - Step By Step (34 min 18 sec)

Posted by jmxp69 | Yesterday @ 12:29 PM | 4,043 Views
The Grand Cruiser is put together and ready to fly!

Dynam Grand Cruiser v2 RC Plane Build Review (12 min 11 sec)

Posted by montis | Yesterday @ 09:07 AM | 4,383 Views
Mini review of the RunCam TX100 Nano VTX.

Specifications
Frequency Channel: 5.8G 37CH
Output Power: 25mW / 100mW
Working Current: [email protected] 150~300mA
Voltage: 4.5–5.5V
Video Input Impedance: 75 Ohm
Antenna: U.FL 5.8G 2dB Omni antenna
Weight: 1.5g (with antenna)
PCB Size: 14mm*14mm

RunCam TX100 Nano VTX package contains only the VTX, linear antenna and silicone wires.



The weight of the TX100 is only 0.9g without antenna and wires.



The weight with supplied atenna is 1.5g.

...Continue Reading
Posted by xortig | Yesterday @ 08:07 AM | 4,579 Views
Name: horns_mounts_covers_set_01.png
Views: 2
Size: 375.5 KB
Description:
As a special promo offer we have made our quick install servo mounts and control horns available for download from
Xortig.com
Posted by Boneswamped | Jan 22, 2020 @ 07:40 PM | 5,734 Views
Boneswamped
St. Croix Models Long-EZ:

Just picked this kit up from an old friend. Complete, Un-started in original packaging. All the documentation is in the box and all the parts are in pristine condition. I can’t wait to get this gem from 1984 started. Anyone that has one of these kits please leave pics of your build, and any info you have. I will be updating many of the build techniques to today’s standard. The aircraft will be electric as well. More to follow as soon as I get started. 😁
Posted by Cox PT-19 | Jan 22, 2020 @ 04:53 PM | 6,215 Views
Another afternoon spent working on "piddly stuff" with the Jr. Skylark. The servos were dry-fitted (and may get shuffled around) inside the fuse.

The original Skylark was designed NOT to have an elevator, so one was installed. The nacelles are also shaped and finished. Everything got sanded and I'm done with that stuff!

I'm also down to my last precious tube of Ambroid Airplane Cement! The end of an era!
Posted by GroundControlRC | Jan 22, 2020 @ 02:22 PM | 6,402 Views
Sneak Peek on my Build Progress of the MinimumRC B-25 Mitchell

Here is a link to this Plane:
https://www.minimumrc.com/b25-mitchell-p0082.html

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #MinimumRC #B25Michell #B25 #Bomber

This Plane is Courtesy of MinimumRC!

The Build of this Plane has gone very smoothly thus far and I'm making some very good progress.
With a bit of luck, and time, I should have the Airframe completed tonight.

See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Ground Control RC™ Glue & Fly™ Series Scratch-Build Planes

Consider Supporting Our Channel by becoming a Patron at: https://www.patreon.com/groundcontrolrc
Patrons of the Channel will have access to the latest Aircraft Plans & Exclusive Content!

See Us On Youtube | Patreon | RCGroups

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
Posted by Crman441 | Jan 22, 2020 @ 12:49 PM | 6,563 Views
Looking for a saito fg33 new or used have a gee bee I’d like to put one in let me know!
Posted by BDOG1 | Jan 22, 2020 @ 11:18 AM | 6,736 Views
I f you have been following my blog/build on the DAW Mustang you might have notice a picture or 2 of something else being worked on .
Yes -a old school DAW 2m 1-26 .
The build has some modifications to the standard build of yesteryear :
First - I have cut the fuse down the middle to add a carbon rod for strength,
I also added a coroplast nose/spine to the front of the plane to protect the battery {I use LiFe batteries and I know that fire concerns are a very real hazard in other parts of the country and else where in the world } the plastic nose makes the servo placement easy and strong and should keep the shape of the nose intact even in the worst crash I could imagine

Second - I made the wing 2 piece along with a removable stab to make transportation/shipping easy { Thank You Jan for the modification Help ! }

Here is a photo dump of my progress :...Continue Reading
Posted by kopterheld | Jan 22, 2020 @ 09:36 AM | 6,832 Views
FatShark Dominator HDO 2
408,64€ - $455 - 9% Coupon: 2020cNy - https://www.banggood.com/custlink/KmGKeeY4pN
9% Coupon: 2020cNy gilt auf alles auch FPV Sachen.
Fatshark HDO2 with new 1280x960 (4: 3) OLED displays and 46 degrees FOV. The best FPV goggles on the market
Banggood guarantees duty-free shipping via Priority Direct Mail or EU Priority Line


Video - FatShark Dominator HDO 2 TBS Fusion RapidFiRE and antennas DE (EN subtitle)
FatShark Dominator HDO 2 TBS Fusion RapidFiRE Module Antennen (7 min 44 sec)




Pic 1 - Fatshark HDO 2 delivered from Banggood

...Continue Reading