Pete ulibarri's blog View Details
Posted by Pete ulibarri | Sep 25, 2019 @ 01:36 AM | 3,585 Views
I recently ordered this little dlg from the UK. I reached out to Neil Harrison at about acquiring one of these little Toro's, and after several messenger messages, this dlg was headed my way and arrived about a week later. The box was superbly packed with excess amounts of bubble wrap and all the parts were in perfect condition.

I looked up the Toro build video on youtube done by Jerme' Andre, and used that as my basic guide for proceeding. Ill link that video here to help anybody who's interested.

I'll also add some pictures and info on the build. For most folks the Toro will be a basic DLG build. There is room enough in the fuse to get all the servos and electronics installed without much trouble. It also is awesome that it has a nosecone so no need to tape a hatch down like some other models in the past.
I went ahead with the recommended servos (bluebird bms101mg). I thought about using a couple mks servos I had laying around for the flaperons, but decided to go with the bluebirds for now as the gliders CG was just about perfect with them. I think the xtra 8grams from the mks would have been a bit too much and I didn't wish to figure a workaround for them, though they would fit if I wanted to push the issue.

Here is the weights of all the parts for the build.

Wing: 50gr
Fuse: 21gr
Rudder: 4gr
Elevator: 4gr 7gr
Battery: 9gr
Reciever: 7gr ( - the case so probably 5gr) (Spektrum AR410)
Servos:...Continue Reading
Posted by Pete ulibarri | Feb 14, 2018 @ 01:37 AM | 15,599 Views
Hello folks,
These are a few micro dlg models thad I started making for fun. Ive tried to make them as realistic as possible with shaped airfoils and near accurate fuses. My graphics are not perfect, but they have been fun projects to work on. Its been discovered that they fly a little if you add nose weight to balance, however they are fragile so I do not recommend throwing them
Ive been making them here and there for others, to model their personal planes. They take a little time to create each one, so Im starting to get a list of orders to fill. If you reach out, I'll answer as soon as I'm able, I'll keep making them for a wile as Ive been saving the funds from making these to get myself a new dlg, currently my eye is set on the concept x5. Takes a lot of micros to get one of those! I make them as I have time, some weeks are busier than others, so it takes a week or to to get them out sometimes. I happy to see that they are being enjoyed!...Continue Reading
Posted by Pete ulibarri | Jul 30, 2017 @ 08:45 PM | 20,710 Views
I thought Id get the ball rolling on a build I did of the 1M Hawk DLG that Nikoli Gorban is selling from the Ukraine. I bought the it from a fellow who purchased this kit and several items from Nikoli.
I didn't take pictures during the build, but I'd like to share what I did, what I did wrong/right, and learn from others on what may work better.
Getting Info is a little difficult as Nikoli does not speak much english. I messaged him via Facebook a few times and did get some basic info from him.
Here is what I have as of now.

Airframe kit weight: 86gr
(Fuse, wings, elevator, and rudder with control horns attached)

3 dymond 47 2 for flaperons, 1 for elevator
1 Hitec HS-35HD for the rudder.

Receiver: Spektrum Ar6100E

Battery: Venom 1s 250mah

CG: 55mm

AUW: 132g

Im using the Hitec servo in place of another dymond, because I was doing QT's and dropped the plane on the tail which broke the servo gears(didn't have any damage to the tail!)
The fuse is super small and not much else will fit in there. the hitter is .5gr lighter than the D47 but has about 1/2 the torque.
If there is something smaller with decant torque that will fit in this airframe Id like to know.
I built the servos into a "brick" similar to what is shown in one of the build threads for the 1M strike2. I used Kapton tape and a small amount of shoe goo to hold the servos to the small fiberglass plate that came with the kit, then glued the brick into the fuse...Continue Reading