xinte's blog View Details
Posted by xinte | Oct 24, 2018 @ 03:26 AM | 1,683 Views
New LDARC TINY GT7 75mm / GT8 87.6mm Mini FPV RC Racing Drone Betaflight F3 10A Blheli_S 800TVL Cam 5.8G 25mW VTX 2S PNP BNF
https://www.xt-xinte.com/New-LDARC-T...F-p557402.html
Configuration:
Tiny GT7
Wheelbase:75mm
FC+ESC:
Betaflight SPRACINGF3
4in1 ESC 10A BLHeliS
VTX:Q25OSD(25mW 16CH Smart OSD V1)
Camera:OV231(800TVL 150° NTSC)
Motor:XT0803-9000KV
Prop:1535
Battery:7.4V 380mAh 50C(XH2.54)
Weight:40.5g(no receiver and battery)
Receiver:RX2A PRO,DSM2,AC900(S-FHSS+D16)

TINY GT8
Wheelbase:87.6mm
FC+ESC:
Betaflight SPRACINGF3
4in1 ESC 10A BLHeliS
VTX:Q25OSD(25mW 16CH Smart OSD V1)
Camera:OV231(800TVL 150° NTSC)
Motor:XT0804-7500KV
Prop:1935
Battery:7.4V 380mAh 50C(XH2.54)
Weight:47.8g(no receiver and battery)
Receiver:RX2A PRO,DSM2,AC900(S-FHSS+D16)
Posted by xinte | Oct 24, 2018 @ 03:05 AM | 1,612 Views
Happymodel Mobula7 75mm Crazybee F3 Pro OSD 2S Whoop FPV Racing Drone Quadcopter w/ Upgrade BB2 ESC 700TVL BNF Compatible Frsky Flysky DSM2/DSMX Receiver

https://www.xt-xinte.com/Happymodel-...r-p555452.html

We will give you an extra 2 sets of paddles. There are 4 sets of blades (2 sets of red + 2 sets of black), one of which is installed on the plane, and the warehouse is shipped randomly with black or red.


Specification:
Brand Name: Happymodel
Model: Mobula7
Item Name: 75mm Wheelbase 2S Brushless Whoop FPV Racing Drone
Wheelbase: 75mm
Version: Basic Version / Standard Version ( Optional)
- The diffirence of them are the package charger.
Basic Version: USB Charger
Standard Version: 6-way Charger
Receiver ( Optional): Compatible Frsky NON-EU Receiver
Compatible Frsky EU-LBT Receiver ( XM+ Receiver)
Compatible Flysky AFHDS/ AFHDS-2A Receiver
Compatible DSM2/DSMX Receiver

Size: 98mm*98mm*36mm
Weight: 25.9g (without battery)

Crazybee F3 Pro Flight Controller Item Name: Crazybee F3 Pro FC
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-2S battery input (DC 3.5-8.7V)

Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Receiver ( Diffirent version having diffirent receiver)
Built-in Betaflight OSD(SPI Control)
Built-in Current meter Max 28A
Current...Continue Reading
Posted by xinte | Sep 13, 2018 @ 05:20 AM | 1,848 Views
New EMAX Mini Magnum II 2 F4 Flying Tower Flytower 4in1 OSD VTX 6S BLHELI 32BIT 35A Flight Controller for FPV Racing Drone Parts

https://www.xt-xinte.com/New-EMAX-Mi...X-p553719.html

Mini Magnum 2 F4 6S BLHELI 32BIT:
Introducing the next generation of the famed Magnum line, the Mini Magnum 2.
Next Generation ESC Board:
Featuring a 35amp BLHeli32 capable ESC board, current sensor, on-board capacitors, and capable of running 2-6s lipo batteries, no longer will there be limits to the capabilities of an all-in-one stack in this 20*20 formfactor.
Tuning, Easier than ever:
Engineered around an F4 processor with an MPU6000 gyro, tuning and perfect flight performance will be easier to achieve than ever. Including built-in programmable RGB LEDs, distinction between different builds and custom status updates offer a wide variety of customizability for any situation and requirement.

Remote channel control:
Ytilizing a newly engineered video transmission frequency controller, channel selection can now be programmed from an exrernal transmitter without On-Screen-Display, information regarding your craft will be easy to access while in flight directly on your video feed.

Proven Formfactors:
With all the electronics needed, assembled together in an accessible package, building a custom craft will only require a frame, camera, set of motors, and a compatible receiver.
Instalattion has never been easier, thans to the universal formfactor of the tower system.

Weight specification
Total weight: 17.21g
Flight controller
(OMNIBUSF4 Firmware)
STM32F405 MCU
MPU6000 accelerometer/gyro (connected via SPI)
On-board OSD
On-board Buzzer
Integrated 5V/3A BEC
Dedicated PPM/ Sbus receiver input
30x27mm board with 20mm mounting holes.

ESC
Continuous current 35A ( max burst 40A)
Supply voltage 2-6S Lipo( 1700kv Motor LIMIT for 6S )
STM32F051K6U6 MCU
BLHeli_32 firmware,support DSHOT,MULTISHOT,ONESHOT125
Top quality MOSFET
3oz high TG PCB board
32x37mm board with 20mm mounting holes.
Current Sensor

VTX
Frequency band:5658-5945MHz (FCC Compliant Channels / with HAM unlock)
TBS Audio Control
Channel:37
Transmit power:13dBm/23dBm(25mW/200mW)
Supply voltage:4.5V-5.5V
Antenna port :50Ω
Posted by xinte | Sep 12, 2018 @ 05:14 AM | 2,019 Views
XT-XINTE New Mini FPV Goggles 3 inch 480 x 320 Display Double Antenna 5.8G 40CH Built-in 3.7V 1200mAh Battery Should be the Cheapest FPV Goggles ,
https://www.xt-xinte.com/XT-XINTE-Ne...s-p521424.html
what do you thinks of it?
Any cheaper one with same function and quality? welcome to recommend to me,thanks
Posted by xinte | Sep 12, 2018 @ 04:25 AM | 1,706 Views
10 Pairs AVAN Rush 2.5 Inch Props 3 blades Propellers CW CCW for Emax 1106 Motor Lipo 3S to 4S Babyhawk FPV RC Racing Drone Quadcopter Model
https://www.xt-xinte.com/10-Pairs-AV...l-p548986.html
The Emax Avan Rush propeller 2.5x1.9x3 was designed for Babyhawk Race 2.5 inch conversion kit to maximize performance and flight time. This propeller is matched to Emax 1106 4500kv for 4s or the Emax 1106 6000kv on 3s. A true 1.9" pitch throughout the blade gives a linear control feeling across the throttle band while still achieving high speeds. This allows for ease of flight and more precision. With a special PC blend the Avan Mini weighs 1.25 grams. Utilizing thicker airfoils greatly increases durability and stiffness. Most of the weight is centralized near the hub creating a low moment of inertia of 1.24 grams*square centimeter which in turn makes a very responsive prop.



The Avan Rush was designed from the ground up starting from design constraints such as RPM, air speed, and required thrust. From these constraints aerodynamic models were built to predict performance and to design the blade shape. Highly cambered airfoils were used to achieve high lift coefficients at high angles of attack prolonging stall. This allows for a higher blade angle while still remaining efficient. The cambered airfoils also allow a greater flight envelope making for great low end responsiveness while still being able to achieve high speeds.



A special Polycarbonate blend is used to achieve high durability. This material is incredibly tough and ductile to resist fracture in high impact crashes. A thick blade root was designed to further increase this durability. Our injection mold process is optimized to reduce bubbles in the plastic to increase the strength of the propeller and to maintain superb balance.



AVAN Rush 2.5 inch prop (2xCW 2xCCW) 1 set kit



Geometry:

2.5 inch diameter

1.9 inch pitch

3 blades



Inertial Properties:

weight: 1.4 grams

Moment of Inertia: 1.24 g*cm^2



Packing list:



10pcs*CW 2.5inch propellers

10pcs*CCW 2.5inch propellers
Posted by xinte | Aug 16, 2018 @ 01:15 AM | 1,888 Views
Snapper7 Brushless Micro 75mm 5.8G FPV Racer Drone 2.4G 6CH RC Quadcopter RTF 700TVL Camera VTX & Double Antenna Mini Goggles
https://www.xt-xinte.com/Snapper7-Br...s-p524823.html

Package include:
1 x Snapper7 Brushless Micro 75mm Racer Drone
1 x JMT LST-009 Double Antenna 5.8G FPV Goggles
1 x Flysky FS-i6 6CH 2.4G AFHDS 2A LCD Transmitter

This is RTF Version, Ready to Fly, All Assembly.

Drone Detail:


Specifications:
Mode Name: Snapper7
Wheelbase: 75mm
Size: 98.5mm*98.5mm*36mm
Drone Weight: 28g(without battery)
Features:
Betaflight support , multi flight mode: ACRO/AIR/ANGLE
Powerful Brushless motor and Smooth ESC
CNC aluminum alloy propeller guard
Betaflight OSD support ,easy to get RSSI , Voltage and other info from your goggles
Adjust the settings and the PID of the flight controller via OSD
Full telemetry function ready
Head lights ready
Camera angle adjustable
Real Bind and Fly version
FPV Goggles Detail:

Highlight:
Double Antennas
Built-in 3.7V 1200mAh Battery
Support a key search frequency
RaceBand 40 channel Auto-Searching
Real-time video return 5.8G FPV Receiver


Feature:

● Small size and light weight;
● Low power consumption, Working current 300~330mA;
● Double antenna reception to make the signal more stable;
● RaceBand 40 channel, Auto-Searching;
● 3.0 Inch 480*320 dot high brightness LCD screen;
● Built-in super sensitiveness 5.8GHz 40ch receiver, especially with RaceBand;
● Built-in 3.7V/1200mAh high-capacity Li-ion polymer Battery;
● Universal USB charging interface;
● Real-time video return, Very low time-delay;
● Bilingual menu in support of Chinese and English;
● Support external video signal input;
● Support AV signal output (Connect external DVR);
Posted by xinte | Aug 05, 2018 @ 10:00 PM | 1,376 Views
JMT TX600 25/100/200/400/600mW Switchable

48CH 5.8G FPV VTX Video Transmitter Module OSD Control for Mini Racing Quadcopter RC Drone

https://www.xt-xinte.com/JMT-TX600-2...e-p537745.html

Description:

Item name: TX600 VTX
Output power: PIT/25mW/100mW/200mW/400mW/600mW switchable
Control mode: BFOSD control(RX)Button
BAT: 5V+
Video system: NTSC/PAL
Antenna: IPEX
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362-5945 MHZ
(TX600's factory set up is on lock mode(5733-5866MHZ unlock). Please follow your local laws and regulations
if you need to unlock the frequency.)

Size: 26*26mm(L*W),Hole:20*20mm
Weight: 2.3g

Package Included:
1 x TX600 VTX
1 x 5.8G Linear Antenna
1 x 6Pin Cable
4 x M2x5 standoffs 5mm tall Nylon
4 x M2 Nylon Nuts



Features:

- 25/100/200/400/600mw switchable
- Lightweight designed
- Build-in PIT mode
- Smart port
- Frequency lock on
- Clean fliltering , interference rejection ablity
- Won't interfere with other VTX while it's powering up in different frequency

Warning
Red area on frequency table is locked area! Please
follow your local laws and regulations .
Long press for 20s to unlock or reset all set up .Please re-power after unlocking.
We suggest the VTX and Camera work on the same 5V. Black means the light is on.

Precautions for use:
-Input voltage must be kept + -right
-Please choose antenna with good VSWR and DB if you replace, to get far transmission distance
Posted by xinte | Aug 05, 2018 @ 09:57 PM | 1,427 Views
Simonk Firmware 30A ESC Electric Speed Controller with 5V 3A BEC for 2 to 4s Lipo Battery

https://www.xt-xinte.com/XT-XINTE-Si...3-p134503.html


Get a Coupon code here https://www.xt-xinte.com/Coupon-cp2444-5bdb7f.html




Specification:

weight: 25 g

Input voltage:2-4S

Working current:30A

BEC output: 5V 3A
Posted by xinte | Jun 25, 2018 @ 05:32 AM | 2,760 Views
JMT Crazybee F3 Flight Controller OSD Current Meter 4 IN 1 5A 1S Blheli_S ESC Compatible Frsky / Flysky Receiver for Whoop Drone
Frsky or Flysky Receiver optional, Please choose the item according to your transmitter.

https://www.xt-xinte.com/h-product-d...oods_id=486690

Specifications:
Firmware: Betaflight_3.3.0_Crazybee
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Flysky receiver with telemetry AFHDS/AFHDS-2A compatible
Built-in Betaflight OSD(SPI Controll)
Built-in Current meter (Max 14A,could be modified to 28A by replace resistor)
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready
Board size: 28.5 * 28.5MM
Board weight: 3.5 g

ESC parameters:
Power supply: 1S LiPo/LiPo HV (4.2v/4.35v)
Current: 5A continuous Max 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Motor connector: JST PH1.25 3pin
Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM

Receiver parameters:
SPI BUS receiver
Frsky D8/D16 switchable
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitting and receiving 1 m from the ground): 300m
Failsafe support

Package Included:
1 x Crazybee flight controller ESC Flysky/Frsky receiver
Posted by xinte | Jun 14, 2018 @ 10:22 PM | 3,017 Views
Beecore VTX Brushed Flight Controller for Tiny Whoop Built-in Betaflight OSD and 25mw VTX with Smartaudio

https://www.xt-xinte.com/Beecore-VTX...o-p527543.html

The tiny whoop style Brushed flight controller built-in Betaflight OSD and 25mw VTX with Smartaudio is coming now. Best for Kingkong Tiny6/6x/7/7x .
Specifications:
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in Betaflight OSD(SPI Controll)
Built-in 5.8G 25mw 40ch vtx
Smartaudio function ready
Heading LED Ready
Mount hole distance: 26mm * 26mm
Board size:29mm*29mm
Board weight: 4.0 g

Features:
With 4 large current NMOS transistors, operating current of up to 10A each
Built-in OSD(Using F3 MCU controls OSD over SPI bus in DMA mode)
Smartaudio ready, you can change the VTX channels by your radio sticks
PPM/SBUS/IBUS/DSM2/DSMX ..etc protocol receiver compatible
Best for Tinywhoop style brushed frame , perfect flight controller replacement for Kingkongrc/LDARC Tiny6/6x/7/7x/8/8x
Posted by xinte | Jun 13, 2018 @ 03:31 AM | 2,787 Views
JMT Crazybee F3 Flight Controller OSD Current Meter 4 IN 1 5A 1S Blheli_S ESC Compatible Frsky / Flysky Receiver for Whoop Drone
Frsky or Flysky Receiver optional, Please choose the item according to your transmitter.

Specifications:
Firmware: Betaflight_3.3.0_Crazybee
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Flysky receiver with telemetry AFHDS/AFHDS-2A compatible
Built-in Betaflight OSD(SPI Controll)
Built-in Current meter (Max 14A,could be modified to 28A by replace resistor)
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready
Board size: 28.5 * 28.5MM
Board weight: 3.5 g

ESC parameters:
Power supply: 1S LiPo/LiPo HV (4.2v/4.35v)
Current: 5A continuous Max 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Motor connector: JST PH1.25 3pin
Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM

Receiver parameters:
SPI BUS receiver
Frsky D8/D16 switchable
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitting and receiving 1 m from the ground): 300m
Failsafe support

Package Included:
1 x Crazybee flight controller ESC Flysky/Frsky
Posted by xinte | Jun 13, 2018 @ 02:56 AM | 2,503 Views
AT10 / AT10II online upgrade

https://www.xt-xinte.com/RadioLink-A...r-p133765.html


The latest AT10(AT10II) version V1.3.7 firmware upgrade on Sept. 27, 2017.



Download of bin_af90_V1.3.7 .(AT12S).mac : https://mega.nz/#!NZ9VSbKJ!j74qjMyzx...CYwY2jbHsXhC4I



Download of bin_af90_V1.3.7 .(AT12S).bin : https://mega.nz/#!Jd0TWaza!kQb350oUH...zl8qk2Qg-c0ebc




Improvement:

1. ADD: Add Throttle Position alarm funtion, transmitter will warning if throttle is not at the lowest position when power on.
You can setup Throttle Position alarm funtion on or off in SYSTEM menu



/************************************************** ************************************************** ************************************************/

The latest AT10(AT10II) version V1.3.0 firmware upgrade on Sept. 7, 2017.



Download of bin_3c57_V1.3.0 .(AT12S).mac : https://mega.nz/#!tB1yDIib!IyG0A5bBs...qjraLQ6PVRuYXs


Download of bin_3c57_V1.3.0 .(AT12S).bin : https://mega.nz/#!lE1mzDJJ!4oSro5cC7...6lfayMA8pN6jvA




Improvement:

1. Improved: Joysticks adds more filtering.
2. Add: Add CAR and BOAT model type.
3. Add: AT10/AT10II will alarm if throttle do not at the bottom when power on.
4. Add: RSSI signal strength pass through on a spare channel, can setup CH5 to CH12 as the RSSI signal output channel.
5. Change: the RSSI signal strength display change from figure to percent, 100% show the strongest RSSI signal.



/***********...Continue Reading
Posted by xinte | Jun 13, 2018 @ 02:53 AM | 2,268 Views
T8FB 8CH transmitter upgrade doc

https://www.xt-xinte.com/RadioLink-T...e-p133821.html

T8FB 8 channels transmitter upgrade file download: https://mega.nz/#!1E8XXYxA!TsuM02c8c...Ys-OBuUevD6tqM



Include:



1. T8FB Upgrade Driver: for WIN7 & XP、WIN8 & wWIN10



2. T8FB Upgrade Tools & T8FB Latest Frimware



3.T8FB Parameter setup tool by Phone / Computer



4.T8FB User manual







T8FB Parameter Configuration:Guidance: http://radiolink.com.cn/doce/t8fb-pa...iguration.html



T8FB Firmware Upgrade or Model Type Change Guidance: http://radiolink.com.cn/doce/t8fbchangemodetypes.html
Posted by xinte | Jun 13, 2018 @ 02:51 AM | 2,316 Views
CB86-PLUS Balance Charger firmware upgrade document





The latest version V2.4 is updated on July.25th,2016



CB86-PLUS-V2.4.bin VUP Download : https://mega.nz/#!Yd8BnboI!8toYiGuVd...si-fkybftVtiUU

CB86-PLUS-V2.4.mac VUP Download : https://mega.nz/#!8Y9B2bBZ!_SBWMsr_e...DekHPuBkdB8uys



CB86PLUS upgrade steps :



1. Put your CB86PLUS via USB cable to your computer.



2. Connect CB86PLUS to a suitable DC power supply with 10.5-15V output voltage and minimum of 15A output current.



3. It appears like disc on your computer.



4. Format original files(Format original file means format the transmitter files when you bought. For example, your CB86PLUS is the version V1-8, you want upgrade to the version V1-9. Then you have to format the file of V1-8 , and then copy the file of V1-9. So the file V1-8 is the original file).



5. Copy upgrade file.



6. Put USB cable off.






The differences between mac and bin files.



(1)File mac for new version CB86PLUS which can upgrade by computer with win7, win8, XP and APPLE.



(2)File bin for old version CB86PLUS which only can upgrade by computer with win7, XP.





The differences between new version and old version CB86PLUS.



(1 ) Appear hint “format files”, display shinning when connect CB86PLUS to computer.



(2)Without any hint, only display is on constantly when connect CB86PLUS to computer.



...Continue Reading
Posted by xinte | Jun 13, 2018 @ 02:48 AM | 2,297 Views
AT9 / AT9S Firmware Upgrade V1.7.5 (AT12S)_c0f0.dfu is updated on Oct.10, 2017



Download of V1.7.5 (AT12S)_c0f0..dfu: https://mega.nz/#!MQVEXbCK!1tLc3boHn...b5tnDPBbZ6C0ng



Improvements:



1. Add THR-HOLD function in MULTIROTOR model.



/************************************************** ************************************************** ******************************/

AT9 / AT9S Firmware Upgrade V1.6.6 (AT12S)_821c.dfu is updated on Sept.7,2017



Download of V1.6.6 (AT12S)_821c.dfu: https://mega.nz/#!JUFECZxT!bNvAWrA3e...-_kVgHTxhT7was


Improvements:



1. Improved: Joysticks adds more filtering.
2. Add: AT9/AT9S will alarm if throttle do not at the bottom when power on.
3. Add: RSSI signal strength pass-through on a spare channel, can setup CH5 to CH12 as the RSSI signal output channel.
4. Change: the RSSI signal strength display change from figure to percent, 100% show the strongest RSSI signal. /************************************************** ************************************************** ******************************/


AT9 Firmware Upgrade Diver Document Download——June 6,2015



AT9 remote control upgrade driver for WIN7/WIN8/WIN10/XP system: https://mega.nz/#!VNl2BAAC!_PdH-5oYo...Lqsy6ACECjGAmM



Firmware upgraded for PC (XP system) download: https://mega.nz/#!IAVxDBQB!I-VgEP_it...E6FExulTeecEmc



Firmware upgraded for PC (WIN7/WIN8/WIN10 system) download: https://mega.nz/#!...Continue Reading
Posted by xinte | Jun 13, 2018 @ 02:44 AM | 2,341 Views
Radiolink AT9 --- USB data backup copy function introduction


Operation video:copy data by USB for AT9(in Chinese)

http://v.youku.com/v_show/id_XMTUwMj...rom=s1.8-1-1.2



Radiolink AT9 data copy by USB V1.0 system download :

https://mega.nz/#!EEsnFIiA!b0fCMzoqZ...pGyUgATG_l40nY





Note 1: When use USB cable connect to AT9, it’s better to reopen "Radiolink AT9 USB data copy system V1.0".

Note 2: Before use "Radiolink AT9 USB data copy function", run "ctlUpdate_step1.bat" first.

Note 3: When the first time to open “Radiolink AT9 USB data copy V1.0 system ”, need to run as administrator.

Note 4: There need to have “DD” sound when write data into transmitter, there must be have something wrong with the copy system if doesn’t have “DD” sound, please reopen "Radiolink AT9 USB data copy system V1.0”, return on the AT9, reconnect the USB cable.



Steps:

1. AT9 have to upgrade to V1.3.3 first if you need use the copy function. The instructions how to upgrade the firmware, please refer to this video.

RadioLink AT9 Firmware Update (8 min 21 sec)




2. Turn on transmitter, then connect to computer through the USB cable.



3.Turn on USB data copy function in MODEL SEL. menu: Choose BASIC MENU-> MODEL SEL.->COPY→PC:ON



4. Open “AT9 USB data copy system V1.0”.



5. Click”CONNECT”, green light on means connect successfully.



6. Read the AT9 data: click “...Continue Reading