Posted by Monkey Hobby | Yesterday @ 01:33 AM | 1,345 Views
New Product !! Volantex Mustang P-51D 4 Channel Beginner Airplane with 6-axis Stabilizer System and One-key Aerobatic (761-5) RTF

In stock now!!

It is a good plane for begineer.


Specification:

Brand: VolantexRC
Length (in): 15.7000
Wingspan / Width (in) : 12.5000
Flying/Running Weight (lbs): 0.1
Material: EPP Foam
Motor : 10mm coreless motor
Speed Control: None
Recommended Battery: 3.7V 360mAh lipo battery
Charger: USB Cable
Radio: 2.4Ghz 4-Channel
Flaps: No
Flying Time: 14 minutes
For Age Over: 14 years
Experience Level Beginners ~ Expert
Where To Play: Outdoor
Is Assembly Required: No


FEATURE:
【Easy to control】4 channel control with Aileron, great sport performance, easy to do aerobatic. 6-axis gyro stabilizer provides superb stable flying even controlled by rookie pilot. Suit for both beginners and experts.
【One-key Aerobatic】This function includes “flip” and “roll”, means that the airplane can do aerobatic automatically in two direction if you turn it into beginner mode and use this function. Everyone could enjoy the aerobatic flight even if he/she is a new pilots.

【Durable Material】EPP composite material, high flexibility, excellent recovery, not easy to break.
【Suitable for multiple locations】Apply to indoor and outdoor flight, longer remote control distance and 60g flying weight.
【Fully Assembly】True ready-to-fly (RTF version) package allows the plane to take off within 2 minutes after you open the box.


You can purchase in this website:
https://www.monkeyhobby.com/new-prod...tic-761-5-rtf/
Posted by old4570 | Yesterday @ 12:38 AM | 1,397 Views
Free Flight SU-27 found on Feebay ..
With discount , cost around $5 USD or less .

Wow ! Came fully bent in the post ( see pictures ) ..

But it was an opportunity to test some ideas I had .
Got out the old clothing iron , bumped the temp to 80deg C and proceeded to iron out the wrinkles .
Nope , not doing a good job !
Bumped the temp to about 120deg C and I was just starting to melt the foam ..
At just over 90deg C the iron was doing a half decent job .
I had 2 layers of house hold paper between the foam and the iron at all times .

But there was a lot of bent to go around .
The motor had got bent as well and would not straighten out .
So I had to cyno it reasonably straight .

Assembling !

So the parts have these little tabs that get pushed thru holes .
The foam is SOFT , I mean soft .
Best to use needle nose pliers , very carefully push the pliers into the hole and just barely thru ..
Grab hold the TAB , and pull it thru ..
Much easier than trying to push the tabs thru the very small tight holes .

Once assembled .. Its not overly bad !
CG looks to be about right , and you just need to tweak the control surfaces for a decent glide .
It's windy outside , so the SU 27 glides like a tissue ..
Really need some UBER low wind ( no wind ) or possibly a decent indoor space .


Free Flight Micro Capacitor Powered SU27 (1 min 3 sec)


Was windy yesterday ..
This morning was calm , but a slight drizzle ..
Oh that weather !
Posted by Hobby Details | Oct 14, 2019 @ 08:36 PM | 1,721 Views
1/10 On Road Alu Drifting Car Wheels 5Star Style 4pcs/set
Dia: 52mm, Width: 26mm Hex: 12mm
DTOW03001A:Purple
DTOW03001B:Gold
Wholesale Price please PM or contact me at: [email protected]
Posted by LemonC | Oct 14, 2019 @ 03:27 PM | 2,336 Views
FalcoX BeeBoppin (8 min 1 sec)


Really loving this falcoX stuff. If you are tired of trying to tune consider giving a flightone fc a shot in the future.
Posted by unboxingexp | Oct 14, 2019 @ 11:29 AM | 2,517 Views
Brand Name: Goteck
Item NO.: GS-1502
Item Name: Analog micro servo
Size(mm): 1.8x1.4x0.05
Torque: 80g-cm
Weight: 1.5g
Power supply: 3.7V/5V

Micro linear servo (1 min 2 sec)

Posted by GLSJr | Oct 14, 2019 @ 11:05 AM | 2,553 Views
Are drill millimeters the same as bullet millimeter sizes (3,4.5,etc)?
Posted by carlosjml4 | Oct 14, 2019 @ 08:46 AM | 2,975 Views
Enjoying FPV flight and testing functions in video editing. I hope you like it!

Have fun with my videos and help me with the subscription, it only costs you a click ;-)) Thank you !!!

LOOK AT THE VIDEO


Posted by CarreraGTSCS | Oct 14, 2019 @ 06:00 AM | 3,307 Views
Posted by prachar223 | Oct 13, 2019 @ 10:15 PM | 3,628 Views
Hello all,
I wanted to share a video of the maiden flights on the Imperial Knight Twister built and flown by William C. Nichols of Grove City, Ohio. The Knight twister biplane has a special part of history for Ohio. Don Fairbank's was from Cincinnati, Ohio and the full scale version of this plane is on display at Sporty's Pilot Shop located in Batavia , Ohio. Furthermore, for Bill Nichols, growing up in New Philadelphia, Ohio he would often see another version of the Knight Twister being flown by Tony Sabler.

In the early 2000's he built a 1/2A version of the Imperial Knight Twister, this is powered by a Norvel .074 motor and flies great! Always wanting to build a larger version it happened to be fate, when a plan, cowl, wheel pants, and the long discontinued Magna-lite material the original construction article called for was found at a swap meet in Washington Courthouse, Ohio. It was without delay that this was purchased. It took Mr. Nichols approx 2 years off and on to complete the Knight Twister and after going on a two show model tour and taking "Best of Show" at both events, the biplane was taken up for a maiden earlier this week. The model won "Best of Show" in 2018 at the Westerville Model Swap Shop/Show and at the Lancaster Model Swap Shop/Show both located in Ohio.

Below is a video of the models maiden flights, the aircraft flies great, was balanced perfectly and only required a few clicks of down trim.

The model is of 1/3 scale and...Continue Reading
Posted by Hobby Details | Oct 13, 2019 @ 08:31 PM | 3,184 Views
20 Holes Aluminum RC Tool Stand for Screwdrivers 230x84x20mm
DTEL01028: Black Gold
DTEL01028B: Red
20 Holes: 14mm*4 / 19mm*12 / 20*4mm
Wholesale Price please PM or contact me at: [email protected]
Posted by Bill M - RC | Oct 13, 2019 @ 08:22 PM | 3,225 Views
Hi fellow rc enthusiasts

HAIBOXING RC review. This HAIBOXING Hailstorm 4WD RC Buggy review includes unboxing, inspection, functions, features, duration and a drive test in wet conditions.

Get this HAIBOXING RC Cars 1:18 Scale 4WD Off-Road Buggy 36+KM/H High Speed 18858, 2.4GHz All-Terrain Waterproof Remote Control Trucks, Hobby Grade RTR Electric Remote Control Cars for Kids and Adults in UK here: https://amzn.to/2q6o0rT

HAIBOXING Hailstorm 4WD RC Buggy review (15 min 35 sec)

Posted by unboxingexp | Oct 13, 2019 @ 01:04 PM | 3,498 Views
Posted by turbinefancy | Oct 13, 2019 @ 10:12 AM | 3,599 Views
Showing some high and low views around Orange County Modelers Association Field - Bob Swenson Memorial Field aka Black Star at Silverado, CA. Matched with iconic music and some smooth precision acro down low. Enjoy!

OCMA FPV Dusk Tour Low & High (3 min 56 sec)

Posted by Cjhana | Oct 13, 2019 @ 09:49 AM | 3,604 Views
Hi guys and gals
So far everything seems to be working on the software however when I disconnect led and try to startup (in att mode) using one of four csc commands I get a double yellow blink then 3 red blinks and if I continue holding command led blinks green three times only once, then back to yellow and red blinks? Is this normal?
Also I noticed when I was calibrating sticks the elevator bar moved to -1000 but only 987 the other way after calibration would this effect csc commands starting motors? I bypassed MC to make sure my esc were working , when I connected to throttle channel on rx they all worked fine? Please help
Posted by Montanaman2 | Oct 13, 2019 @ 08:56 AM | 3,703 Views
Needed
Posted by GLSJr | Oct 13, 2019 @ 06:26 AM | 3,882 Views
Does anybody know if there is a gage for determining the size of bullet connectors?
Posted by rsilk | Oct 13, 2019 @ 02:34 AM | 4,166 Views
The default serial speed of my HC-05 is 9600 baud which was fast for serial communications in 1975, but I decided to increase it to 57600. The module is connected to S5, so I needed to set the SERIAL5_BAUD to 57. This can be done in various ways, depending on your Ardupilot ground station software.

To change the serial speed on the BT module it is necessary to use a USB/TTL adapter to set the device in "AT" mode which on my module is achieved by holding down a button switch while powering on. In this mode the default speed is set to 38400 baud, so I configured the communication speed on the terminal software to match.

Using the terminal software (Serial USB Terminal on Android phone), I connected to the USB/Serial converter:
AT
OK
AT+UART=57600,0,0
OK

After disconnecting and rebooting, I was able to connect to the ground station at a much faster speed via BT
Posted by rsilk | Oct 13, 2019 @ 02:28 AM | 3,975 Views
The Frsky X8R receiver sends RSSI data back to the XJT Frsky transmitter module so it can be displayed on the radio. However, I wanted to also display it on my groundstation. I believe the same applies for OSD.

The RSSI signal lead on the X8R receiver is connected to the RSSI pin on the F405-Wing. The receiver is connected to the FC via SBUS.

I have set the Arduplane rssi params:
RSSI_TYPE 1
RSSI_ANA_PIN 15
RSSI_PIN_HIGH 3.3
RSSI_PIN_LOW 0

RSSI values are displayed as percentages.