R/C Blogs - RC Groups
Posted by Jack Crossfire | Today @ 12:45 PM | 66 Views
The answer is no, you can't align the rear wheels. They're doomed to wear out from being toed in. The tires can't be removed. H King sells an alternative set of wheels with removable tires. The rear wheels can't be swapped with the front wheels.
Posted by craytech | Today @ 12:37 PM | 64 Views
Makerfire VR008 Pro FPV Goggles (8 min 18 sec)


Hello everyone welcome back.

Today I have a new pair of FPV goggles by Makerfire. This googles are awesome and a big upgrade from my previous goggles.

Here are the specs
High brightness 4.3 inch LCD specially turned for FPV racing or Model airplane, Light weight 295g with 2hr 2000mAh battery, RTF for any scale, racing, Model airplane game.
Ergonomic design fit your faces.
Built-in super sensitiveness 5.8GHz 40ch receiver, especially with RaceBand.Come with advanced auto-searching function ad show you the working frequency on screen.
Built-in 3.7V/2000mA battery, each full charge revive around 2 hours working time.
92% transparent lens adopted, no distort, no blur on the adage of screen,4.3 inch 480*272px HD high brightness LCD.


Here is what all comes with the goggles

1 * FPV Goggles 1 * Flat Antenna 1 * Mushroom Antenna 1 * Video Cable 1 * USB Charging Cable 1 * Power Adapter 1 * Carrying case


Great deal on amazon
https://www.amazon.com/gp/aw/d/B0749...OWL&ref=plSrch


Thanks for watching.

Stay tuned for more videos

Like and Subscribe!

Stay Safe and Fly Often

CRayTechVlog
Posted by rcduder | Today @ 11:59 AM | 77 Views
Hey there guys, last night after some long thought about it I decided to create a patreon page for myself and my flying and the progression of my channel. My goal out of this is to put it right back into my content that I will be creating for you guys! Even working a full time job on top of my freestyle flying and my current sponsor from gens ace/tattu it can be hard to produce the quality content I want with the limited equipment I have. So please consider supporting me via patreon!

https://www.patreon.com/PNWFPV

Wether the support comes in from you guys or not the content will continue to come dont worry! But this will allow me to be able to progress into proper content and the goals I want to reach with it much faster then just what my full time job allows me to support.

Thanks for reading guys and please check out my latest videos!!! Ill give you a little hint at whats to come, 5 inch chameleon first flight video!!!

Thanks guys!!!

-Michael Anderson/PNWFPV
Posted by teralift | Today @ 11:02 AM | 128 Views
For summarizing compatibility of different cameras with BF3.2's Camera Control feature.

Please provide the following information

Status (OK or NG):
Camera model:
Flight controller model:
Firmware version:
Mode (PWM or Software PWM or DAC when available):
Resource assignment (camera_control line from resource list output):
Reference voltage (camera_control_reference_voltage):
Internal resistance (camera_control_internal_resistance):
Control key delay (camera_control_key_delay):
Inline register value for PWM and capacitor if software PWM:
Posted by Bad Company | Today @ 11:01 AM | 116 Views
Bought it in February and finally got to the assembly table this month! Maidan went well......but it is true......the Mini Talon not likes but LOVES a long Fast approach! Just some fine tuning, attach the pan & tilt set up and it will be out some distance on a regular basis.
Posted by nigelsheffield | Today @ 09:45 AM | 221 Views
Here is my review on the boldclash f02h camera from boldclash.( Work in progress )
Plus a preview of my next review which will be a high end 1s lipo charger for whoop batteries and any other 1s batteries.
I'll start with some pictures and a couple of video showing it's looks and performance both of which are pretty nice!
Name: IMG_20170921_181120.jpg
Views: 1
Size: 298.9 KB
Description: Name: IMG_20170921_172736.jpg
Views: 1
Size: 406.5 KB
Description: ...Continue Reading
Posted by 1nspectorGadget | Today @ 09:44 AM | 178 Views
FEILUN FX176C1 GPS Brushed RC Quadcopter Full Review - PART 1 (29 min 30 sec)

This is Part 1. I had to break up the review or the video would have been an hour long. Lot's to cover with this one. One of the few cheap toy grade quadcopters with GPS.
Posted by Srdlv | Today @ 09:22 AM | 176 Views

Hi all - wed like to introduce you to our custom scale license plates - any state, country, or design available -

SRDLV.COM

FB - sikridesdesigns
IG - SRDLV & SIKRIDES
Posted by DutchRC | Today @ 06:51 AM | 284 Views
Halloa people

for an upcoming project I needed me a Slightly smaller FPV camera, and offcourse I could have just gone with the RC Swift Mini.. While looking that one up though, I came across a new contender in the arena of FPV cams: the Caddxx Turbo S1.. They claim it to be better in several aspects, so I decided to compare the 2

Option nr.1: the Runcam Swift Mini

Option nr.2: the Caddx.us Turbo S1

And this is what things look like side by side:

DutchRC - Runcam Swift Mini vs Caddc Turbo S1 FPV Camera's - Good alternative?? (16 min 0 sec)


Caddx Turbo S1 specs:
sensor: 1/3" CCD
res: 600tvl 4:3
TV system: Pal or NTSC (non switchable)
lens: 2.5mm 1.2F
WDR: yes
OSD: yes
power in: 5-40V
weight: 12g
dimensions: 22 x 22x 27mm

Runcam Swift Mini specs:
sensor: 1/3" CCD
res: 600tvl 4:3
TV system: Pal or NTSC (non switchable)
lens: 2.5mm 1.2F
WDR: yes
OSD: yes
power in: 5-36V
weight: 12g
dimensions: 22.3 x 22x 27mm
Posted by TINGW | Today @ 02:48 AM | 393 Views
You can order it from :http://www.bonroytech.com/views.asp?hw_id=416

Item name: F4 PRO
Size: L42 * W36mm
Hole distance: 30.5*30.5mm
Net weight: 11.2g (exclude wire)

Specifications:
* OMNIBUSF4 firmware
* Master STM32F405 GRT6, refresh rate up to 8K
* PCB 3OZ copper enhance current stability and cooling fast
* 5V 3A BEC output
* Exposed pad for easy soldering
* Compatible with all ESCs, as well as DYS 4-in-1 esc without soldering
* Integrated OSD, no need to flash firmware additionally,debug OSD via BF ground station.
* Integrated current meter to monitor the real-time power consumption
* Adjust the PID by OSD via remote control
* Adjust the VTX via open ports such as power, frequency band, frequency point (Note: The VTX should have this function like TBS one and the upcoming DYS VTX.)
* DYS F4 flight control with 4 damping balls reduce the vibration to make it fly stably.
* 2-6s lipo support
* Net weight: 11.2g (exclude wire)
* Size: L42 * W36mm, hole distance: 30.5*30.5mm
* Gyro: MPU6000
*3.3 V Voltage output
* Include PPM VTX and RSSI VTX
Posted by zanek | Today @ 01:35 AM | 426 Views
Here's a short clip from last summer that I shot following a car

DJI Matrice Following Car (2 min 14 sec)

Posted by eslipring | Today @ 01:14 AM | 442 Views
Slip ring is used to connect two relatively rotated 360 and current or signal transmission components, there is a common number of channels 1-36 channels. With the continuous development of industry, equipment is more and more complex, the number of slip ring channel demand increased, multi-channel slip ring can meet this demand.

JINPATs LPC Capsule Slip ring channel can up to 125 wires, the number of channels LPT through bore slip ring channel can up to 300 or even higher, while the power ring, signal ring, hybrid signal, fiber and hybrid signal, high-frequency signal is mixed with the power can be achieved.

JINPAT has been producing fiber optic rotary joint for over ten years, is famous for its quality products, which are produced not only in the domestic slip ring also in the world to get many customers, the products are exported to Europe, America, Japan and other developed countries.

Multi-channel optical fiber is widely used, but because of the difficulty of processing and complex design, which is very expensive, many industries and fields due to budget exigencies. Cannot use the multi-channel fiber optic slip ring.
Posted by TINGW | Today @ 12:38 AM | 468 Views
Know more detail by this link:http://www.bonroytech.com/search.asp?action=search

*X160 is the micro racer for FPV hobbyist. It is a high-integrated product with highly flexible control. *Equipped with motor 1104-4000KV, propeller 3x2 as well as the popular BLheli 10A esc (Oneshot support). Flight range of remote control more than 1000 meters.
*To gain the quality and real-time shoot for FPV, X160 also combines 5.8G 32CH 200mW transmitter(the switch can shift between 20mW and 200mW) with 1/3''CMOS lens, which supports 127 or wider 160 shootings and every moment brings you the exciting FPV experience.

*This latest V3 with OSD for the video, the real-time status will be returned back to the display. Flight control SP F3 flash with CleanFlight, just connect the battery, receiver and set the remote control to use.

Brand: DYS
Item name: X160 V3 RC Micro FPV Racer
Wheel base: 160mm
Frame size: 148mm(L)x131mm(W)x41mm(H)
Propeller: 3020 propellers
Motor: 1104-4000KV
Camera: FOV127 (160D)
ESC: 10A ESC with BLHeli firmware (support oneshot)
Antenna: 5.8G mushroom antenna
Flight controller: SP racing F3
With OSD
Weight: 143g (included motor, ESC, and propeller, without battery)
Battery: recommend 3S 800-1000mah (not included)
Flight range of remote control: more than 1000 meters
Combines 5.8G 32CH 200mW Transmitter with 1/3" CMOS Lens, supports 127 or wider 160 degree shooting.
Four frame arms integrated 10A high speed ESC
Receiver and remote control not included
Posted by old4570 | Yesterday @ 11:35 PM | 482 Views
Bad news - For me !
My order for the WL toys 977 was cancelled ( I was really looking forward to flying this one ) Shuzbutt !




The good news !
Who does not love motor tools ? I love them ...
But there has always been one issue that gets my claw ! The inserts for drill bits and tools ..
They never seem to be just the right size .. Especially for drill bits .

I was on banggood just cruising all the goodies they sell when my eye spied this motor tool with a chuck .. ( A Chuck )
I just had to have it ( for review purposes mind you ) .. Because I love motor tools .
Currently on back order ...

Now I haven't seen a motor tool with a chuck before , this is a first for me so excuse me if I'm a little like a 8 year old waiting for Xmas . So hopefully some time in October I will have a really cool motor tool to play with ( eeeer I mean review ) .
Posted by jefffassbinder | Yesterday @ 11:27 PM | 475 Views
Starting another build of a 90mm Hawk. Just putting the ducting together and ready for some carbon tow.
Posted by TINGW | Yesterday @ 10:42 PM | 502 Views
Six color for your choice: http://www.bonroytech.com/views.asp?hw_id=418
Item name: ELF - 83mm micro brushless drone
Motor: BE1102-10000KV
ESC: 4-in-1 BLheli_S F10A Dshot
Prop: 1.7 inch
FC: F3
VTX: 25mW 40CH
Lipo: 2s 600mAh
Basic Info:
Wheel base:83mm
Weight:80g (battery included)
Motor:BE1102-10000KV
ESC:4 in 1 Blheli_S Dshot F10A
Prop: Micro 5 blades prop
VTX: 5.8G/40CH/25MW
VTX distance:300M
Lipo: 2S 600Mah
Flight time: Around 6 minutes
Camera:1.8mm 170(no microphone)
Below is the flying video for you to review:
Indoor flight of DYS Elf 83mm Micro Drone. (1 min 29 sec)

Posted by Choppahman8 | Yesterday @ 10:06 PM | 526 Views
This will test the performance of a straight leading edge versus the swept wing. Also will have the directly under wing mounted motors. I've been speculating if this is the single factor why the C-1 outperforms other versions in vertical manouvers.
Posted by bighead93 | Yesterday @ 10:06 PM | 521 Views
https://m.mixcloud.com/ben-berry4/

So another of my hobbies is DJ'ing and mixing! Some good stuff to fly to if you are into dance music
Posted by dz1sfb | Yesterday @ 08:53 PM | 644 Views
Announcement, Ken's CAD Models is migrating to a new web site. Here's the address.

https://www.kenscadmodels.com/

Mind you, it is a work in progress, but I am really liking Wix.com web hosting so far.

Ken