Posted by Old_Pilot | Today @ 05:38 PM | 209 Views
Well POOP !.....Just spent the last hour looking through 1130 Sport C/L plans on OuterZone, hoping to find something that I might want to convert to R/C....Pretty much all the stunters look the same, as do the combat wings.....I converted the Altagerra several years ago, and although it's a good looking and great flying airplane, I've built her twice.....So I wanted something different ..be careful what you wish for...I drew this one up in 2018 for a Balsa Builders Conversion Contest on RC Groups, until the moderator changed the contest rules to include anything that was already in the hangar.....no primary build time....so I backed out and never built her....55" 1911 Caudron Racer, complete with a 3-cylinder Anzani.....I know, I know....I've lost my mind
Posted by kopterheld | Today @ 02:09 PM | 454 Views

DarwinFPV Baby Ape is a 3 inch freestyle quad with 1104 4300KV motors for 2-3S battery. 73g, F4 FC 15A ESC's BL_S, Darwin700TVL Camera, the Pro Version is with CADDX ANT Camera. I would only take the Pro version because of the better Caddx ANT camera.

Video EN subtitle -
DarwinFPV Baby Ape Pro der billigster 3 Zoll Freestyle FPV Quad (5 min 18 sec)



Connection of EP1 ELRS receiver to UART1
The Happymodel EP1 is soldered as shown in the photo. Telemetry should be off otherwise the VTX will switch to B1. No solution in sight yet. There are no problems with a Frsky XM+ receiver or other SBUS receiver.

DarwinFPV Baby - Code: BGDARWIN10 - https://www.banggood.com/custlink/3mmRAWc40K
DarwinFPV Baby frame - Code: BGRCPARTS8 - https://www.banggood.com/custlink/3KvysieNen
DarwinFPV F4 12A 3S AIO - https://www.banggood.com/custlink/D3KEnV8LhB
BlueJay ESC FW - https://esc-configurator.com
BetaFPV ELRS Micro TX - https://bit.ly/belrs1w
Eachine TX16S - https://www.banggood.com/custlink/DGvyoHno4j
Happymodel ELRS EP1 - https://s.click.aliexpress.com/e/_AgqSef

Kopterheld Coupons:
https://t.me/s/KopterHeld

My equipment:
DJI FPV Goggles V2 - https://www.banggood.com/custlink/DDmRIkhAdY
Fatshark Dominator HDO2 - https://www.banggood.com/custlink/KmGKeeY4pN
ImmersionRC RapidFIRE - https://www.banggood.com/custlink/vm3v6vafP1
Radiomaster TX16S - https://www.banggood.com/custlink/vGvKMV73QP
CADDX Ratel 2 - https://www.banggood.com/custlink/GDvEFB6wnC

Youtube – https://www.youtube.com/kopterheld
Blog – https://kopterheld.tv/
Instagram - https://instagram.com/kopterheld
Twitter - https://twitter.com/kopterheld
Posted by rickp | Today @ 09:00 AM | 941 Views
Posted by High_Start | Today @ 08:32 AM | 960 Views
Hello, I΄ve decided I wanted to do more with my youtube channel.
Here I post footage of my build logs planes and more.
If you are interested in my rc videos, here is the link:

https://www.youtube.com/channel/UCxL...ItnqmNu5Q3JayQ
Posted by kopterheld | Today @ 04:31 AM | 1,339 Views
URUAV RX5808 EVO the cheapest and best FPV Module - 48 Channel FPV Module for Fatshark or DJI FPV Goggles, an analog module with OSD adjustment in the goggles, better than Eachine Pro58, same as Foxeer Wildfire.

Review (EN subtitle) -
URUAV RX5808 EVO günstiges Modul für Fatshark und analog DJI FPV Brille (2 min 27 sec)


URUAV RX5808EVO - https://www.banggood.com/custlink/vvDy5tnhgU
DJI RX PORT 3.0+ - https://www.banggood.com/custlink/vvGyYTb6wR
BDI adapter - https://bit.ly/digiada2
TBS Fusion - https://bit.ly/f24fusion
ETHIX Strap HD - http://bit.ly/ETHIXHD
Alien 2200mAh - https://www.banggood.com/custlink/vKmYiu5W7a
RapidFIRE - https://www.banggood.com/custlink/vm3v6vafP1
DJI FPV Goggles - https://www.banggood.com/custlink/DDmRIkhAdY

Kopterheld Coupons:
https://t.me/s/KopterHeld

Youtube – https://www.youtube.com/kopterheld
Blog – https://kopterheld.tv/
RCGroups – https://goo.gl/JYP87D
Telegram - https://t.me/s/KopterHeld
Instagram - https://instagram.com/kopterheld
Twitter - https://twitter.com/kopterheld
Posted by kopterheld | Today @ 04:28 AM | 1,350 Views
ExpressLRS 2.1 is here and you can use the BetaFPV ELRS Micro TX module with the 2.1 firmware. The basic settings can now be set with the joystick on the back of the OLED display. The Namimno Flash V2 also works with ELRS 2.1 and the OLED display with joystick function.

My video (EN subtitle)
BetaFPV ELRS TX Modul 1W mit ExpressLRS 2.1 (1 min 36 sec)


ELRS Micro TX 1W - https://bit.ly/belrs1w
ELRS Nano TX - https://bit.ly/BF2ELRS2NANO
Amazon - https://amzn.to/3s6RBQa

LiteRadio 3 - https://bit.ly/literadio3
Meteor65 Pro - https://bit.ly/meteor65pro
Amazon - https://amzn.to/3DVo6mr

Meteor75 - http://bit.ly/Meteor75
Amazon - https://amzn.to/31YDOjV

Meteor85 - http://bit.ly/Beta85ProV2
Amazon - https://amzn.to/3oTZdU5

ELRS Lite RX - https://bit.ly/ELRS24LITE

Micro Nano Adapter - https://bit.ly/BFM2NAD
Eachine TX16S - https://www.banggood.com/custlink/DGvyoHno4j

Kopterheld Coupons:
https://t.me/s/KopterHeld

Youtube – https://www.youtube.com/kopterheld
Blog – https://kopterheld.tv/
RCGroups – https://goo.gl/JYP87D
Telegram - https://t.me/s/KopterHeld
Instagram - https://instagram.com/kopterheld
Twitter - https://twitter.com/kopterheld
Posted by DumbthumbsFPV | Today @ 04:14 AM | 1,343 Views
My review of this beginner drone
DJI FPV Drone Combo and accessories (39 min 24 sec)

Posted by Old_Pilot | Yesterday @ 08:42 PM | 2,036 Views
For all intents and purposes, she's done, but it will be a while before I try to fly her......low's in the 20's and teens, highs in the 40's with winds at 10-15 , probably until March
Posted by aero nishi | Yesterday @ 05:54 PM | 2,532 Views
Synergy with Whoop Fc (0 min 33 sec)


I installed Whoop FC, Crazybee F4 Pro V3.0, on Synergy from RC Factory. FC works as a receiver, ESC and gyro and weighs only 4.3g. It has 2-4S input, 10A ESC, and 1A BEC, so I think it is suitable for Synergy class aircraft. The range of the built-in receiver is not long, so it is recommended to use it for indoor flight.

・Servo Connection
Servos can be connected to pads which can be set to timer output ports. For this FC, LED_Strip, TX1, RX1, TX2, and RX2 pads can be used. (IRX1 cannot be used because it is connected to an inverter. BUZZ also cannot be used because it cannot be set to a timer output port.) I used LED_Strip, TX2, and RX2 pads for Servo 1 (AILERON), Servo 2 (ELEVATOR), and Servo3 (RUDDER). They are connected to PA0, PA2, and PA3 of the MCU. Betaflight resource commands are:

resource servo 1 A00
resource servo 2 A02
resource servo 3 A03

The wiring diagram, actual wiring, and assembling the servo connector are shown in the pictures.

・Betaflight Setting
The motor is connected to the M1 connector. FC is placed so that the M1 connector is facing forward and attached to the back of the fuselage (see photo). The board alignment is roll 0 pitch 0 yaw -45.

Betaflight command I used are as follows:

resource led_strip 1 none
resource serial_tx 2 none
resource serial_rx 2 none
resource servo 1 A00
resource servo 2 A02
resource servo 3 A03
mixer customairplane
mmix reset
mmix 0 1 0 0 0
smix reset
...Continue Reading
Posted by phil alvirez | Yesterday @ 07:32 AM | 3,439 Views
as i coundnt understand the meaning of that box that shows at some posts, i began to speculate.
here are the pics as they change when i press or roll. this example is with a 3 positions switch.
https://www.rcgroups.com/forums/thum...one&starter=no
am under the impression that when i press or roll, changes something from white to black background, and this means that white is not active and black is. then when roll it moves to different position of the 3 of the switch and start all over for each of the 3 positions.
still dont get it when it is white and there is a small black spot under, sometimes is smaller, others is wider; sometimes there is another on top also. this may be white or black. also, the square piece at the bottom sometimes is half white/half black.
and also there are some notes in the "manual" that comment on them.
i hope my doubts can easily be explained and this will be of great convenience for me and many others that use this series of radios and are in the same situation.
but wait, am beginning to see the light. for those who have the manual, or have access to it on line, see page 8: there is a drawing near the bottom left that tells: 'tip' here you find some data. and below, next to it, there is another clue in auto switch select. also in page 31 at top. and page 32 at the end. seems that the fellows that wrote the manual never considered that there are no explanations about this so we could...Continue Reading
Posted by kiwi_craig | Yesterday @ 04:30 AM | 3,721 Views
Bell Huey UH-1N, Ken Lou’s latest fuselage design for the OMP M2 joining his other awesome kits for the M2 , 230S and k130 helis.

High quality SLA 3D printed resin shells and parts. Kits come with welded SS landing skids, tail frame sub assembly and awesome clear plastic screens and all fasteners and related and a decent amount of surface detailing. Ken is running these with the trex 250 - 205mm cf main blades.

Look up ken.Lou.906 on f a c e b o o k You will not be disappointed

Also see the bell B427

https://www.rcgroups.com/forums/show...7-fuselage-kit

And the OH-58. Bell B206 jet ranger

https://www.rcgroups.com/forums/show...Ken-Luo-design...Continue Reading
Posted by Cabledawg1 | Yesterday @ 12:35 AM | 4,091 Views
Parts edwen may be interested in. The yellow on the thrust thingamajibs are because I painted the bottom of the plane yellow so it was easier to see.
Posted by Jack Crossfire | Yesterday @ 12:27 AM | 4,126 Views
The embedded GPUs are out there. They're just 3x the price 2 years ago.

The lion kingdom believes the biggest improvements are going to come from improving the camera more than confusing power which no longer exists. Improving the exposure would improve every algorithm, so back light compensation is essential. Exposure could be adjusted so 99% of the pixels land above a certain minimum on the histogram. Unfortunately, the GeneralPlus has limited exposure control. Polling the video4linux2 driver, you get some settings.

id=980900 min=1 max=255 step=1 default=48 Brightness
id=980901 min=1 max=127 step=1 default=36 Contrast
id=980902 min=1 max=127 step=1 default=64 Saturation
id=980903 min=-128 max=127 step=1 default=0 Hue
id=980910 min=0 max=20 step=1 default=0 Gamma
id=98091b min=0 max=3 step=1 default=3 Sharpness
id=98091c min=0 max=127 step=1 default=8 Backlight Compensation

The only functional ones are contrast, saturation & backlight compensation. Backlight compensation is really some kind of brightness function. Saturation & contrast are some kind of software filters. The values have to be rewritten for every frame. Color definitely gives better face tracking than greyscale. The default backlight compensation is already as bright as possible. Changing saturation & backlight compensation from the default values gave no obvious improvement.


Face tracking could use higher resolution. There was also using a bigger target than a face by trying other demos in opencv-4.x/samples/dnn.

openpose.cpp ran at 1 frame every 30 seconds.

person-reid.cpp ran at 1.6fps. This requires prior detection of a person with openpose or YOLO. Then it tries to match it with a database.

object_detection.cpp ran at 1.8fps with the yolov4-tiny model from https://github.com/AlexeyAB/darknet#pre-trained-models This is a general purpose object detector.

Since only 1 in 4 frames are getting processed, there could be an alignment & averaging step. It would slow down the framerate. It wouldn't do well with fast motion.
Posted by GBLynden | Yesterday @ 12:05 AM | 4,171 Views
This is my Arrows BAe Hawk 50mm EDF Jet Unboxing, 4-Channel RX Radio Setup, Arrows Viper Comparison, & Review video!

Arrows BAe Hawk 50mm EDF Jet Unboxing, Radio Setup, & Review (9 min 43 sec)

Here are my Review Notes:

Pros:
- Easy build
- Nice grips for hand launches
- Skid plates on the bottom of the jet
- It is beautiful! New anti-corrosive paint for better
- High performance 50mm EDF Setup
- Three flight modes with Vector gyro system making it a "Smart Jet"
- Can use 4-Channel RX
- Uses inexpensive 3S packs

Cons:
- The battery bay needs minor mods to ensure a complete seal every time.

Link to Arrows RC BAe Hawk PNP EDF Jet: https://bit.ly/2VY0HB7

The link in this description is an affiliate link. It gives me a small commission on sales which helps support the channel and keep it independent.
Posted by DaVinciBrainchld | Jan 23, 2022 @ 10:36 PM | 4,327 Views
My redesigned avitron ornithopter transmitter. I gave it a retro Aviation/Falconry look with rivets, polished aircraft aluminum, leather, cork, antique brass parts, real Falconry bells, and a bronze falcon skull.

- [email protected]
Posted by DaVinciBrainchld | Jan 23, 2022 @ 09:40 PM | 4,473 Views
Below are pics of the tunnel hull boat I redesigned using a WLtoys rc hull bottom. Still a work in progress...

- [email protected]
Posted by DaVinciBrainchld | Jan 23, 2022 @ 09:33 PM | 4,429 Views
Below are pics of the snowplane style Air-Sled I designed, based on the real life ones built in North America in the 1950 and 60s. It's still a work in progress...

- [email protected]
Posted by Catherine Chen | Jan 23, 2022 @ 08:58 PM | 4,417 Views
Hello Everyone,

This is Catherine from Dongguan QS Electronic Tech Co.,Ltd.

This is QS8-S Female to EC8 Male Antispark Series Harness 8AWG

Connector: 2PCS QS8 Female , 1PCS EC8 Male

Wire: 8AWG Silicone wire Black/Red

Length:60mm


Welcome to contact.

Best Regards,
Catherine
Dongguan QS Electronic Tech Co.,Ltd
www.qsrccn-hobbies.com www.qiangshui.en.alibaba.com
M 86 134 80010457 P 86 (0) 769 84750417 Skype chenmin19911 Email [email protected] / [email protected]
Posted by mjnco | Jan 23, 2022 @ 08:16 PM | 4,434 Views
Finally did maiden flight today. As expected a nice easy flying twin. Maiden done without cowls and back fuselage cone off. Third flight everything mounted and my normal 5 min duration. Lipos showed 3.85 volts per cell after landing. Lipos mounted very back edge of tray and stacked per pair. Flaps extended for last flight causing minor nose pitch up.

Rimfire 50cc motors
APC 22/12 wide e-props cut down to 20.5 diameter
CC 160A HV esc per motor.
12S 5000 per motor. SMC 5000 55c lipos