R/C Blogs - RC Groups
Posted by Barts_Hangar | Today @ 06:12 AM | 19 Views
Check out this beautiful giant scale model of the famous "Fieseler Storch" flying at the BRCM annual Warbirds over the Bay event.
Don't forget to subscribe for more videos coming your way!
Beautiful Fieseler Storch flight (BRCM Warbirds over the Bay) | GIANT SCALE RC PLANE FLYING MODEL (3 min 17 sec)

Posted by Matt tipton | Today @ 05:59 AM | 30 Views
1 2 3 your out. (3 min 35 sec)

Posted by TommyClancy | Today @ 04:14 AM | 84 Views
Hello! Having difficulties locating your CG? here's what you can do just click on this link to see the video
How to locate your CG? (2 min 12 sec)

Posted by martint_1976 | Today @ 04:10 AM | 85 Views
BYOD have just had the opportunity to build the almighty Strix Goblin for one of our good customers!

We are used the following hardware / setup;

-Stock STRIX Goblin propulsion system (Motor/ESC) w/ APC-E 6x4 Prop and Gensace 4S 4000mAh 25C Lipo
-Eagle Tree Vector Autopilot /OSD w/ GPS
-Runcam Swift v2 Camera w/ 2.3mm 150FOV Lens
-ImmersionRC 2.4Ghz 700mW Video Tx (supplied by customer, we used our ImmersionRC 5.8Ghz 25mW w/ Spironet Antenna for test flying)
-2.4Ghz Cloverleaf Antenna
-TBS Crossfire Long Range Tx & TBS Crossfire 8ch Diversity Rx
- FrSky Taranis X9D Plus Radio

The Strix Goblin model flies extremely well, very smooth with a wide speed envelope and has docile handling near the stall. However it's important to make sure that your control throws, expo, CofG and reflex are set up accurately, follow the manuals recommendations. We feel that more experienced pilots could handle a little more control throw, starting with the recommended is a great place to start.

We were impressed with the material quality and fitment of the air frame parts. The finish on the foam wings is fantastic and could be prepared very quickly if you wanted to paint them. The servo's, control horns and push rods are ample for the job, but we would recommend using loctite (non permanent normally blue in colour) on the push rod stoppers for extra security. We found that a couple of the wing bolts did not line up perfectly, but the holes can be slightly enlarged to fix this...Continue Reading
Posted by readysetdrone | Yesterday @ 10:09 PM | 230 Views
Want to learn to fly a fixed wing RC airplane? Check out theXK A600. It has 5 channels, brushless motor and comes ready to fly!
RC Airplane Review - XK A600 Brushless (14 min 47 sec)

Posted by cuavlindy | Yesterday @ 09:17 PM | 245 Views
HOT FREEE SHIIPIN CUAV U-Blox NEO-M8N High Precision GPS For Pixhack Pixhawk PX4 APM Flight Controller


why not try ?


https://www.aliexpress.com/store/pro...78731958o7e64K
Posted by Whiskers | Yesterday @ 09:00 PM | 276 Views
On Sunday morning I had the joy of getting a new friend back on to RC flight after a very long time away from the hobby.
He comes from England and is now living here on the Sunshine Coast. As a youngster he had some experience with the planes his father built and flew.
I was impressed with how well he performed after such a time away from the sticks.
The plane I chose was my EasyFly glider, now very much modified and converted to be an FPV plane. It is the plane mentioned previously in this blog as having been rebuilt after a major crash.
It did not have the FPV pod installed for this session. I'm stupid, but not that stupid.
Anyway, I took the thing up to a good height and handed over the Tx. And he flew quite OK. This is a very easy plane to fly, a thing he commented on, but it was impressive that he did so well.
There was a bit of bad management on my part when I didn't resume control early enough and I had to land about 300 metres away with a sagging battery.
This distance is problematic for my ageing eyesight but no damage resulted.
I also flew Wedgetail, also mentioned previously. It is now fitted with new PVC landing gear.
The thing is quite a handful, being way over powered, short coupled and with large control surfaces. No nice relaxing flight time with this one.
Perhaps I found it a little daunting because I have not been flying recently. When I get back some form I'll probably be wondering why I had to really concentrate so to keep it on track.
It sure has an impressive rate of climb.
No doubt it also would have an impressive rate of decent which could easily end in planetary impact, and it was this that focused my attention.
The wind came up and put an end to the proceedings. But we'll be back.
Posted by UpNup | Yesterday @ 08:16 PM | 303 Views
The Ford Flivver 268 plans are tricky in places. The fin and rudder have details that have to be closely followed carefully.

The fin is 1/8 in. thick to build over the plans. When finished, you have to add 1/32 in. sheeting on both sides.

The rudder is 3/16 in. thick with extremely long and curved laminations. I made everything from cuts to sheeting. However the rudder has no sheeting.

The moment of truth is when the tail wheel bracket has to be inserted into a hole in the rudder and a trough has to be delicately run down the lower spine of the rudder. My alignment was off by only 1/16 in., but that threw the tail wheel off by 1/4 in. To resolve the problem, I could have re-soldered the bracket, but realized it could lead to new problems. I used a metal file to slim the top of the bracket insertion rod and cut the insertion hole on an angle. By gluing on a 1/64 in. plywood curved side, I covered where the bracket popped through the soft balsa.

There are two 1/8 in. dowel rods inserted into the bottom of the fin. Now, that means the 1/8 in. balsa rail gets cut through in two places! I cut the holes carefully and sliced the sides. Then I sanded flat the parts so that the sides didn’t bulge. I used CA to quickly fix the dowels.

When I put the 1/32 in. sheeting on, everything laid flat. I used yellow wood glue on the fin and it alarmed me when the balsa began to limber up. I moved quickly to glue both slides. I layed the glued fin on a Formica kitchen...Continue Reading
Posted by AJWoods | Yesterday @ 04:58 PM | 465 Views
Latest star wars build. Came out very light, so it flies super slow. Build thread with plans https://www.rcgroups.com/forums/show...rs-Snowspeeder

Snowspeeder Project (4 min 43 sec)

Posted by vwbsean | Yesterday @ 03:28 PM | 464 Views
Maiden flight done-cycled three batteries through it today...what a fun flyer ........very satisfied😀
Posted by Thomas B. | Yesterday @ 03:09 PM | 469 Views
Surprisingly, we had quite a lot of snow today.
Honk im Schnee (1 min 54 sec)

Posted by RustyK | Yesterday @ 02:54 PM | 488 Views
Hope everyone has been good and Santa brings you something to show off while at the flying field.


Merry Christmas , Happy Holidays and a Great New Year

RustyK
Posted by Felipe Garcia | Yesterday @ 12:31 PM | 541 Views
P51 from littohot in flight
P51 Littohot (1 min 46 sec)

Posted by Absaroka | Yesterday @ 12:02 PM | 571 Views
Wanted to check out my new Mobius (Runcam died) so I flew the Valiant. Saving the Cub maiden for better weather!
Posted by MrGearbest | Yesterday @ 08:30 AM | 728 Views
Hi Everyone,

I want to share with you one of the best Drones in gearbest, it's the "JJRC JJPRO X3 GPS Brushless RC Drone RTF" + 32% off Coupon




Main Features:
● 1080P Full HD Camera has great performance in capturing the details
● Altitude Hold enables your drone to fly steadily and smoothly in the door environment
● Headless Mode makes it unimportant to adjust your drone's position before flying
● GPS / Auto Low-voltage / Auto Signal-loss Return to Home provides better protection for your drone
● Using the USB cable of Android to charge at any time and in any place, very convenient
● 7.4V 2000mAh high-capacity LiPo battery for long flight time when fully charged
● D1806 2300KV brushless motor, more powerful

Specifications:
Size: 28.5 x 30 x 7.6cm ( including propellers )
App name: JJPRO
App Download: QR code on user manual
Compatible system: Android, iOS
System requirement: Android 4.0.3 or later, iOS 8.0 or later


The Link : https://goo.gl/NPNVhM

The Price before coupon: $169.99
The Price With the coupon : $129.99
The Coupon : JJPROX3

Share with friends, for more coupons and topics : https://www.facebook.com/SMARTGEARBESTNET/
Posted by Saptak Rc | Yesterday @ 07:59 AM | 745 Views
Posted by Saptak Rc | Yesterday @ 07:58 AM | 747 Views
Posted by Saptak Rc | Yesterday @ 07:58 AM | 747 Views