Posted by wattechighland | Yesterday @ 11:03 PM | 131 Views
今回はFRPでWTCを作るつもりです。 WTC(water tight compartment)...not cylinder
ハルの内側の突起物ははルーターで削り落とし。
Name: 01IMG_2716.jpg
Views: 0
Size: 87.8 KB
Description:
Name: 02IMG_2717.jpg
Views: 0
Size: 86.2 KB
Description:
マグネットを4か所仕込むところまで。当初8か所にするつもりでしたが、磁力が強いので4か所に減らしても 可かと。
...Continue Reading
Posted by DoubleEagle | Yesterday @ 08:38 PM | 194 Views
Item No.:E564-003
Model Name: 1:20 RC Mercedes-Benz Arocs Container Truck
Size of vehicle (cm): 60.6*16.1*21.7
2.4GHz
Radio controlled: trailer split joints, trailer hight level control.
Speed: 10km/h
Remote distance: 20 meters;
Simulated Lights/Sounds (mute button)
Rechargeable battery and USB charging line included
For more products visit: http://en.doubleeagle.cc/
Business enquire: [email protected]
Double-Eagle Rc 1:20 Mercedes Container Truck Model toys (0 min 58 sec)

Posted by Bill M - RC | Yesterday @ 06:54 PM | 241 Views
Hi fellow rc pilots & rc enthusiasts

Makerfire Happymodel 3s 11 1v 300mah HV30 60C Lipo battery review. Suitable for power whoops like a HappyModel Mobula 7 HD, FullSpeed Tinyleader, 75mm Crazybee F4 Pro CineWhoop, URUAV UR85/UR85HK etc. I test performance & duration on a Fullspeed Tinyleader HD CineWhoop.

You can get these Makerfire Happymodel 3S 11.4V 300mah Lipo Batteries HV 30C/60C with XT30 connector in uk here: https://amzn.to/2HBE7Tz

You can get these Makerfire Happymodel 3S 11.4V 300mah Lipo Batteries HV 30C/60C with XT30 connector internationally here: http://bit.ly/2WS9S1d


Makerfire Happymodel 3s 11 1v 300mah HV30-60C Lipo battery review (7 min 19 sec)

Posted by deenice57 | Yesterday @ 04:33 PM | 297 Views
My max 5 lost power have to turn it off and on the red light be blinking can someone help
Posted by unboxingexp | Yesterday @ 03:56 AM | 662 Views
Balancing DJI's Ronin-S (2 min 22 sec)

Posted by old4570 | Yesterday @ 12:28 AM | 753 Views
It occurred to me ...
That part of the problem lies with the way the pod is a attached to the boom .
3 screws holding it in place to a carbon plate ..
So a lot of force is applied to 3 very small places on launch ..

So before a problem arises , why not just epoxy the pod in place ?
Create a much larger area to distribute launch energy into !
Anyhow , that's what I have done with the Raven 990 ..
I fibreglass reinforced the pod , then glued it in ..
When the Epoxy dries , it should distribute load much more evenly over a much larger area .. ( + the fibreglass wont hurt too much - I hope )
That vertical fin is still weak as ! Next time it breaks , I will cut it out and rebuild it with more carbon reinforcing .
Posted by old4570 | May 18, 2019 @ 09:04 PM | 781 Views
https://www.rcgroups.com/forums/show...9#post41890549

I have issued a product alert : ( Well - for what ever it's worth )

I removed the pod from my Raven 990 and it has a stress fracture @ the same location as my Mini DLG pro ( where it broke )
Posted by GroundControlRC | May 18, 2019 @ 07:23 PM | 785 Views
Maiden Flight - MinimumRC F8F Rare Bear Pro



Here is a link to the Video:
https://www.youtube.com/watch?v=rugO503Bsr0

This Plug-n-Play Kit is courtesy of Banggood.
I've been wanting to try out one of these Brushed Motor Nano/Micro Planes and wanted to review the Pro Version which is a 4 Channel Plane.
This is our Maiden Flight!
Here we go!

Here is a link to the Build Videos:

Part 1: https://www.youtube.com/watch?v=Sq5FAnQwsS8
Part 2: https://www.youtube.com/watch?v=uEYRIQ5hxxs
Part 3: https://www.youtube.com/watch?v=lvOD2rdSXQw
Part 4: https://www.youtube.com/watch?v=rUDSZR4KKw8

Here is a link to the Pro PNP Version of this Kit:

MinimumRC F8F RareBear Pro 360mm Wingspan 4CH KT Board RC Airplane With 8520 Coreless Motor KIT/PNP - PNP
https://www.banggood.com/MinimumRC-F...47791920140372

Here is a link to the Standard Version Plus Motor & Servos of this Kit:

MinimumRC F8F Rare Bear 360mm Wingspan KT Board Mini RC Airplane KIT With 720 Coreless Motor - KIT+Motor+Servos
https://www.banggood.com/MinimumRC-F...47791920140372

Here is a link to the Receiver I used:

2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC
https://www.banggood.com/2_4G-4CH-Mi...47791920140372

Here is a link to the Servos:

TY Model 1.7g Servo With JST 1.0mm Plug Compatible Spektrum 6400 Series Receiver For RC Airplane
https://www.banggood.com/TY-Model-1_...47791920140372

Here is a link to the Batteries I used:

5X Eachine E011 E011C JJRC H67 RC Quadcopter Spare Parts 3.7V 260MAH 30C Battery USB Charger Set
https://www.banggood.com/5X-Eachine-...47791920140372


See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

See Us On Youtube | Patreon | RCGroups | Facebook

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
https://www.facebook.com/pg/Ground-C...3132721/posts/
Posted by UpNup | May 18, 2019 @ 06:08 PM | 798 Views
Major difference between cutting ply and ribs.

Ply requires tough love. Balsa ribs are like cutting through butter. Ply requires saving room on cuts so you can sand to the line. Balsa requires fluid smooth strokes right down the line. If balsa is poetry, ply is a tirade.

Used the drill bit in my hand drill. Blew smoke everywhere. Still looks like a badger made the inner circles.
Posted by ChrisCro82 | May 18, 2019 @ 05:41 PM | 820 Views
HyperLow RS+ 6s (3 min 39 sec)




So i finally made the leap to 6s and was relatively surprised by both the flight times and power i was getting on this HyperLow RS+ build.
I have another RS+ that is running 4s lipos and it's an amazing quad,and i can honestly say it's probably the best flying quad i've ever flown in all my years of
flying quadcopters. I'm getting anywhere between 3-6 minutes of flight time on CNHL 1250mah 6S lipos and running Emax RSII 2306-1600kv motors.
I'm also running BetaFlight 4.0 with bidir/rpm filter and it's helped out alot,only time i really get propwash is when i forget to apply the throttle to harshly.
I've only been flying this build very rarely because i only have three 6s lipos so far. My next step to improving this

Here is the build list of the quad.

HyperLow RS+ (true x,and 15mm standoffs)
T-Motor 55A Pro
(3) Panosonic 1000uf capacitors
PiroFlip F4 (overclocked to 216mhz)
Emax RSII 2306-1600kv
Runcam Micro Eagle
TBS Nano Pro32
Lumenier AXII (micro)
Gemfan 5149
Posted by Thomas B. | May 18, 2019 @ 04:04 PM | 810 Views
Posted by kallend | May 18, 2019 @ 01:02 PM | 1,083 Views
Make Your Own Inexpensive Centerburner

I have a dozen or so EDF models, most of which are of types that were/are equipped with afterburners. After buying some LED “centerburner” systems, I decided to see how hard it would be to make my own.

This project requires soldering skills, and access to a 3D printer and simple design software (such as the FREE https://www.tinkercad.com ), This article only describes the electronic part; fabricating the adapter to mount the LED unit to the EDF motor is not covered. Anyone familiar with 3D printer design software should have no difficulty in creating a suitable mount. Total cost of the electronic components for the system is less than $16. If you do NOT have these skills, I suggest you buy a ready made unit from one of the people who market them on rcgroups.com.

First, I found a suitable high output amber bulb that has it’s own inbuilt voltage regulator.
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

This is very bright, and runs on anything from 9 – 30 volts. It’s current consumption when full on is only 300mA, and the four brightest LEDs are behind a lens that directs their light along the bulb axis. With a little fiddling assisted by a razor saw I was able to remove the yellow plastic bulb base and expose the inbuilt regulator and its connections. These bulbs are $16 for two at Amazon.

To control it without making a custom controller I found a 10 Amp ESC for BRUSHED motors. $14 for two from...Continue Reading
Posted by Clickety | May 18, 2019 @ 12:44 PM | 870 Views
NEW WEBSITE

My plans have moved to www.jetworks.online due to RCgroups server crashing. As a result I have introduced a small charge which will help cover the cost of the website hosting and domain name and help to support the development of new plane designs. Sorry for the inconvenience. However, I do not wish this small charge to be an obstacle for anyone. If you are put off by the pricing please let me know.

NEW! I will be starting a scheme to make planes available for free for children/youth. Coming soon!

Kind Regards

Craig

For regular news, new plane development and progress, visit my Facebook group called 'Clickety's Jetworks'
https://www.facebook.com/groups/1826...?ref=bookmarks

PARKJET PLANS :-

01. YF-23 Black widow / Grey Ghost _ Pusher/2x55mm EDF.
02. F-35 Lightning II _ Pusher / 60-70mm EDF.
03. JA-37 Viggen _ Pusher / 60-70mm EDF
04. Bae Hawk _ Pusher / 60mm EDF
05. A-10 Thunderbolt II _Twin Pusher
06. Drake _ Pusher.
07. EurofighterTyphoon _ Pusher / 60-70mm EDF
08. Harrier _ Pusher.
09. Tornado _ Pusher / 60-70mm EDF
10. Vulcan _ 2x70mm EDF
11. Su-57 _ 2x 5" Pusher / 2x 64mmEDF
12. F-16 Falcon _ Pusher / 60-70mm EDF
13. B2 Spirit _ 2 x 64mm EDF
14. A4 Skyhawk _ Pusher / 60-70mm EDF
15. Sepecat Jaguar _ Pusher / 60-70mm EDF
16. SU-47 Berkut _ Pusher / 60-70mm EDF
17. English Electric Lightning _ Pusher / 60-70mm EDF
18. Mig 29 _ Pusher / 2 x 50/55mm EDF
19. Mirage III _ Pusher / 60-70mm EDF
20. Mirage 2000 _ Pusher / 60-70mm EDF
21. F-104 Starfighter _ Pusher / 60-70mm EDF
22. Blackburn Buccaneer - Pusher / 50-64mm EDF (X2)
23. F22a Raptor - Pusher / 60-70mm EDF
24. EM-10 Bielik - Pusher / 60-70mm EDF
25. Gloster Meteor twin pusher / up to 64m EDF
26. Bae Tempest - Pusher / up to 70mm EDF
27. Dassault Rafale - Pusher / up to 70mm EDF
28. F14 Tomcat - single/twin Pusher / up to 70mm EDF


NON 'JET' PLANS (Free Download)

Bugatti 100p _ Depron parkflyer.
X-wing Starfighter - Pusher
Bugatti 100p - PSS Balsa Glider