Safe settings for ELRS:

Transmitter (Tx)

Mode: CRSF
BAUD: 400K
for EdgeTx: ADC filter OFF

Read a lot about how compatible the 4in1 module is to many brands and how EDGE Tx is getting more user friendly and needed to check it out.

EDGE TX website :: http://edgetx.org/

A Playlist that is very informative ::

RC Video Reviews (Guides and Tutorials

RC Video Reviews (Snipets)

Read about the USB connection and details on drivers and modes:

https://www.rcgroups.com/forums/showpost.php?p=49281951&postcount=4184

The Windows USB driver can be repair with the Impulse RC Driver Fixer ::

https://impulserc.com/pages/downloads

This site has plane icons for almost all radio brands ::

https://www.air-rc.com/

I got interested in the Tandem X20 radio system for two reasons: Dual band capable and Archer receivers optimized for gas planes with auto-level capability.

The Tandem X20 is a solid radio, a bit small in my hands but A class hardware. FrSky is in rapid ETHOS software development , and I just got in when the software upgrade is getting a little bit easier using the ETHOS Suite.

To be continued....

This thread has some basic information on Radio Flight Modes and channel output.

https://www.rcgroups.com/forums/show...rum-DX9-mixing

One:
I began to transplant Spektrum SAFE receivers to another planes with the XXXXXX receiver. This is the receiver that came installed in the E Flite Apprentice 15S. This receiver had three flight modes: Basic, Intemediate, Advanced.

Two:
AR636A

Three:
AR637T(A)


To be completed...

Form Andy Kunz:

"DSMX allows only 10 channels in 11ms mode. 4 channels (2,3,4 and 6) are at 11ms, and the remaining 6 channels are at 22ms.

If you change to 22ms mode, then you have 12 channels at 22ms and 8 channels variable (22-88).

It shows this on the Frame Rate screen display on IX and NX radios.

Andy"

Reference:

https://www.rcgroups.com/forums/show...postcount=4808

Another view of the thread.

From user Sensei in the Show off your naked wood thread:

"I put Monokote down on a well prepared surface at 250 F. , on all edges or overlaps I goto 350F.

Once all edges are set I slowly go over all solid surfaces at 300 F. This is a very slow process. I iron my open bays at at 350F. as needed.

I use original Windex for putting down all other trim colors allowing ample time for the moisture to leave before ironing with 250-275 F. iron, by doing it this way it is achievable to make the covering look like a painted surface with absolutely no bubbles.

Bob"

Referenced post.

Internet to the rescue...

https://www.calculator.net/triangle-calculator.html

You can use the surface length for one side by measuring it and have the angle given. Give the calculator the following angles: given angle, 90 - given angle, and 90 degrees; for one side the surface length and calculate. The result will give you the side you need.

I am going to collect here resources as I learn about Gas Engines.

FAQ for Gas Engine Newbies:
http://www.rcuniverse.com/forum/gas-...formation.html

COMPLETE GUIDE TO GAS ENGINES! Or GASSERS FOR DUMMIES!
https://www.flyinggiants.com/forums/...ad.php?t=53943

Joe Hobbies Beginners Guide to Gas Engine
http://joehobbies.blogspot.com/2011/05/beginners-guide-to-gas-engines.html

Engine Tunning Basic from TerryCustoms:
https://www.flyinggiants.com/forums/...d.php?t=210976

Discussion on Glow to Gas equivalency:
https://www.modelflying.co.uk/forums/postings.asp?th=92464

Basic Engine Setup by TerryCustoms:
https://www.flyinggiants.com/forums/...34&postcount=2

Engine Repair Service and Blog:
http://aeroscott.com/blog/

How to Document by Yufasa

How to change Faceplates:
http://www.rcuniverse.com/articles/r...-for-everyone/

Features and Questions thread:
https://www.rcgroups.com/forums/show...-and-questions

How to Setup a Model by Yufasa:

Setting up a model from scratch on a Graupner MZ-32 (1 hr 9 min 32 sec)

YouTube.com Graupner's video playlist:
https://www.youtube.com/watch?v=akUS...vhtzWHuRR6JMJy

How to setup Flap to Elevator Mix:

Aileron_Setup_Graupner_MZ-32 (4 min 37 sec)

...Continue Reading

I plan to document in this entry how to replicate simple Spektrum Airwave radio programming tasks that are a little more elaborate to program in the Graupner MZ-24 Pro radio.// Planeo documentar en esta entrada como replicar programación simple de radios Spektrum Airwave en el Graupner MZ-24 Pro en el cual es un poco mas elaborado hacer algunas cosas.

First, Graupner switches as described in the manual
//Primero, descripción de los interruptores que están disponibles en el Graupner

• 1 two-position switch with long handle (S6)// 1 interruptor de dos posiciones con mango largo
• 1 three-position switch with long handle (S3)// 1 interruptor de tres posiciones con mango largo
• 4 three-position switches with a short handle (S1, S4, S5 and S7)// 4 interruptores de tres posiciones de mango corto
• 2 one-side, self-neutralizing three-position switches with long handle (S2 and S8)// 2 interruptores de tres posiciones con neutralizado automático de un lado
• 2 INC/DEC buttons (DT1 and DT2)// 2 botones de INCrementar/DECrementar
• 2 rear proportional sliders (SL1 and SL2)// 2 controles lineales proporcionales
• 4 proportional dials (DV1 - DV4) // 4 controles rotativos

I did not find this information, before buying the Graupner radio and asked for it, but it is in the manual burried in the information for assigning control to channels. // Esta información no la pude encontrar antes de comprar la radio Graupner y pregunte por ella, pero esta disponible en el manual enterrada en la información para asignar controles a los canales.

Percent to time for Spektrum Radios, as stated by Andy:

On Spektrum and JR radios, 100% range = 1100 to 1900us.
125% = 1000 to 2000us.
150% = 900 to 2100us.

Andy

Need to know your servo spline number:

http://www.myrcbox.com/articles/tech...splines-guide/

Necesita saber cuantos dientes hay en el eje de su servo, visite el sitio al que lo lleva el enlace. Encontrara las especificaciones por fabricante.

For me is difficult to send the radio in for a switch replacement because I am overseas. I searched the forums for the correct part numbers for the switch replacements, and it was not that easy, all the information is scattered between comments so I got the lead of brand and correct thread size for the beauty nuts to fit.

My results with part numbers are:

Three position small flat switch:
Digikey PN: 360-3393-ND
SWITCH TOGGLE SPDT 6A 125V
NKK Switches PN: M2013ES4W01

Two position long flat switch:
Digikey PN: 360-3388-ND
SWITCH TOGGLE SPDT 6A 125V
NKK Swithces PN: M2012E4S4W01

Three position long round switch:
Digikey PN: 360-3394-ND
SWITCH TOGGLE SPDT 6A 125V
NKK Switches PN: M2013Q4S4W01

Part numbers provided for : https://www.digikey.com/

After a couple of years in the hobby, I decided to have my first post on the Blog. I am going to try to gather links in this post of information found around the web and this site, that would be of help to beginners. I am going to concentrate on RC Planes, for which I have more experience.

Después de un par de años en el hobby, he decidido hacer mi primer post en este Blog. Yo voy a tratar de recoger enlaces en este articulo sobre información que se encuentra en la Web y este sitio que puede ser de interes para principiantes. Me voy a concentrar en Aviones RC, para el cual tengo mas experiencia.

Servos:
How do you assemble the grommet -eyelet-screw in a servo? Cómo se arma la combinación de elemento para atornillar un servo.

The following post has a picture/El siguiente enlace tiene una descripción gráfica:

https://www.rcgroups.com/forums/show...15&postcount=9