Posted by Nickerz | Yesterday @ 11:32 PM | 35 Views
This morning, I bought a 2nd Great Planes PT-40 but this is the original PT-40 that came out around 1987 I think (whereas version 2, the MKII came out around 2008) and I bought this original version 1 from an RCGroups.com member. Total paid was...

$100.00 (Grand Total)
$100.00 (Plane ARF Kit, Engine & Radio!)
$Free (Shipping)
$N/A (Tax)

This is NIB and I wanted this to keep for nostalgic reasons since this is technically the plane I viewed in the two videos I had as a kid and wanted to buy back then but I felt building it would have been a little more than I was ready for. So now I have that chance and I got such a great deal on this as they go for $250+ on eBay! USPS shows the delivery date between TBD...

Here is the original classified ad...

I already have an engine for it too (NIB O.S. MAX .40-FP which is the original engine recommended in the manual and in the videos I watched as a kid!) I'll take pics and do an unboxing video once I get it. Here's a pic from the seller...


Posted by AlkaM | Yesterday @ 08:56 PM | 450 Views
Many of you will be familiar with some of this already. I skip a lot of things about switching losses and current circulation in the motors. This is about how these two electrical variables affect real world performance. This is to hopefully give an idea of what PWM even is to those unfamiliar.. feel free to post your comments experience down below.
Motors are driven by voltage. In order to control the voltage that a motor coils "pulse width modulation" (PWM) is the process by which this happens. If you have a 12 volt battery and want to run the motor at half speed (6 volts ) you would use pwm with a 50 percent "duty cycle". This means half the time the switches are ON that drive the motors coils and half the time they are OFF.
Pwm frequency ( 24khz, 48khz etc) is the number of times per second that these switches are turned on or off. You could do pwm yourself and probably manage a few switches per second. So picture a toggle switch, when the switch is turned on the current starts to rise in the motor coils and the motor begins to move. When its off the motor will coast and begin to slow down. At a very low frequency like this you can see that it might be hard on a motor as the current goes through large swings with each turn on turn/ off phase. This current ripple creates heat in the motor coils and is a major power loss. To make it smoother you need to increase the frequency. Ideally, to switch fast enought that the current has not enough time to...Continue Reading
Posted by lawrence4 | Yesterday @ 08:17 PM | 474 Views
Test use Beta75 pro 2,
Benefit from longer flight time and cooler motor.
More smoothly under 1S 0.5 startup power.

steps:
1.flashing the support bi-directional DShot firmware(for RPM filter),
download the latest firmware marked “48KHz”.
Firmware that allow to run RPM filter in BLHeli_S ESC for free JazzMaverick:https://github.com/JazzMaverick/BLHe...eli_S%20SiLabs

Firstly find out the code name of your ESC.
Connect to BLHeli Configurator.
You can see your ESC code name in the title, for example, mine Beta75 pro 2 is S-H-50 and download the firmware S_H_50_48_REV16_8.HEX

2.SETUP BETAFLIGHT RPM FILTER
Update your FC to Betaflight 4.1 or newer(for now mine is 4.1.6)

Use 4KHz gyro sampling rate and 4KHz looptime.DShot300 ESC Protocol.
Enable “Bidirectional DShot“, and set Motor poles (for example Beta75 pro 2 motor 08028 is 12 poles)

Under Dynamic Notch Filter:
(suggest)
Filter Range at LOW
Width Percent to 0
Q factor to 200
Min frequency to 90

If the motors are cool, it probably means you can reduce filtering further. But this time you can use the two sliders on the top of the filter tab – Gyro Filter Multiplier and D term filter multiplier.(I test it at 1.2 both)

Reference (details explanation):
1.HOW TO GET 48KHZ ON BLHELI_S ESC (MORE FLIGHT TIME ON TINY WHOOPS!): https://oscarliang.com/blheli-s-48khz/
2.SETUP RPM FILTER FOR BLHELI_S ESC (FOR FREE):https://oscarliang.com/setup-rpm-fil...-esc-for-free/
3.BLHeli Configurator:https://github.com/blheli-configurat...rator/releases
4.BLHeliSuite for BLHeli_S: https://github.com/bitdump/BLHeli (download link in the bottom “Read Me” section).
5.HOW TO SETUP BETAFLIGHT RPM FILTER:https://oscarliang.com/rpm-filter/
6.HOW TO FLASH/CONFIGURE BLHELI_S ESC:https://oscarliang.com/flash-blheli-...-pass-through/
7.Bidirectional DSHOT and RPM Filter:https://github.com/betaflight/betafl...and-RPM-Filter
8.HOW TO FLASH/UPDATE BETAFLIGHT ON FLIGHT CONTROLLER?:https://oscarliang.com/flash-update-betaflight/
Posted by stevster | Yesterday @ 07:37 PM | 639 Views
Here's some pictures of my latest "Covid19 Build". It's a plans built, 1930, 1/4 Great Lakes Trainer 2T-1A
I really enjoyed this build. It was fun to detail. 80" span @21 1/2 lbs. Should putt around like a dream trainer.
Powered by a Sachs 2.4 gasoline engine on electronic ignition with a Sullivan smoke system built into the muffler.
Covered in original, uncolored, Super Coverite, stitched, rib taped, sealed with 2 coats of Minwax Polycrylic polyurethane,
then 2 coats of primer (with a sanding of a Scotchbrite pad between each coat) then finished it off with 2 coats of Rust-Oleum
Gloss Protective enamel. I made my own graphics on my wife's Cricut vinyl cutter. That's fun! Topped it off with a couple
off Bazzboe's (here on RCG) very cool 1/4 scale pilots at the "controls". Maiden coming soon!...Continue Reading
Posted by VicT | Yesterday @ 04:04 PM | 843 Views
I purchased an open stock AR637T receiver a few weeks ago and finally got about 5 minutes of flight today (5/28/2020) after replacing the AR636 receiver that came with the Turbo Timber (TT). The TT had flown the day before and I had programmed her with 5 flight modes using the throttle stick as 1 switch for 3 modes and the D switch for 2 modes. Dual rates, expo, and mixing had audio working fine. I removed the 636 RX and white silicone from the foam and made a plywood floor for the 637T RX. I followed the installation manual and bound the RX to the TT program. I had to reverse the elevator and aileron servo direction. She flew the next day and without SAFE or AS3X I noticed my TT as being very sensitive and not forgiving like the 636 RX.

I had been following the manual included with the receiver and got this far before asking Dave A. HELP.......

Inyourtransmitter’smenu,select:
Forward Programming -> Gyro Settings -> First Time Setup The transmitter will prompt you for all setup steps.
IMPORTANT: Before proceeding with setup, read every information screen that appears on your transmitter
Select NEXT at the bottom of each page to continue.
3. Followtheon-screenpromptstosettheorientation.SelectContinueto complete the two-step auto detection process, or select
Set Orientation Manually. Verify the orientation is correct.
4. Youcanassignanyopenchanneltoaswitch(trimmer,knob,e tc)forgain, and assign that channel for gain. You can assign a switch to a channel from the Forward Programming menu so you don’t have to exit the menu. We recommend using a trimmer, knob, or slider for gain, which will enable you to change the gain value on the fly.
When the setup screens are complete select Apply.
3. AS3XTuningBasics:
1. Perform a control surface direction test, and AS3X reaction test.
2. Test fly the airplane to verify the configuration. In-flight trim changes do not require any further updates.
Posted by Justwingit | Yesterday @ 02:27 PM | 992 Views
So I've been flying my E-flite UMX Cessna Citation Longitude as a belly lander recently...

WHAT A BLAST !!!

This thing is NUTS !
E-flite UMX Cessna Citation Longitude Twin 30mm EDF - This thing is NUTS! (10 min 44 sec)


Enjoy the show and I wish everyone all the best !


Posted by phil alvirez | Yesterday @ 11:46 AM | 1,436 Views
see parts 1-3 at my blog
from time to time, model airplane magazines published articles on sort of science fiction by mad scientists that were performing experiments with remote controlled airplanes.
these were as rudimentary as they could be. free flight planes controlling just the rudder, and that happened erratically. it was sort of lottery to be able to change the direction of the plane now and then.
but, as i said, it was just trying the boundaries of the then fantasy of controlling something at a distance.
this took years and the contribution of countless (and nameless) folks to reach the point of being able to control also elevator, then throttle.
the gear consisted on a car battery placed on the ground that provided the power, connected to a control box that the modeler held in his hands.
those who were present were in awe, and talked about this for a long time to whoever were around.
then came reeds, that improved efficiency. there was 1 channel for left turn, and another for right turn.
when elevator was added, same thing: 1 channel for up, another for down.
then servos. nicads. years later, some1 released the 1st commercial radio control (kraft, i think). and expensive. heavy.
and they were flying on frequencies (72, 27), so you would not have interference.
i recall at los angeles, there was at a place called mile square, that was an emergency airstrip (dont know of still exists), that had large areas designated for each frequency where the ones that were willing to fly formed and awaited for their turn to fly.
it was until, on 2006 that horizon released the 2.4 with which apparently any number of planes could fly without interference.
now we also have cellulars, laptops, gps and whatnot.
boy, the world has come a long way...
Posted by DutchRC | Yesterday @ 11:14 AM | 1,479 Views
Halloa people,

soooo it has been a while since Runcam released the Runcam 2 right? I'm not completely sure but it must have been 4-5 years
Back then the RC2 was a great action-cam option for multirotors and it indeed was the first recorder I strapped onto a quad :P

But.. time moves on and we now finally have a 4K version of it!
The shape of these camera's also make them handy for airplanes which is indeed what I was still using the RC2 for

Link to the new cam: Runcam 2 4K edition - Pillbox style action camera

BUT.. is it any good??

Runcam 2 4K Edition Action Camera! (finally :P) - REVIEW (25 min 0 sec)



Specifications:
shape: pillbox
max video res: 4K (at 30 fps)
max frame rate: 120 at 1080P
shutter speed lockable: yes
ISO lockable: yes
video codec: MP4 - H264
max photo res: video only
field of view: 155 degrees
max CF card size: 128 GB
microphone: yes
external microphone: ?
gyro stabi: limited
WIFI config option: yes
battery: 850 mah 1S Lion
max recording time: 1.5 hours at 1080P 60
viewfinder screen: on phone via WIFI
touch-screen: nope
second (front) screen: nope
usb-type: micro USB
water proof: nope
Posted by GLSJr | Yesterday @ 09:06 AM | 1,752 Views
I have been trying to find some information on the toxic effects of soldering fumes. Now that I have switched over from nitro to electric, I am spending A LOT of time soldering. Web searches always assume I am talking about wave soldering in a factory. Does anybody know of a site that can give me an answer to this? I can only hold my breath so long. Thanks
Posted by GroundControlRC | Yesterday @ 07:02 AM | 2,444 Views


Yak54 Aerobat EPP 800mm Wingspan 3D Plane - Flights 3 & 4 - It's a Keeper ;-)

Yak54 Aerobat 800mm Wingspan Kit
https://www.banggood.com/custlink/mDKGw3NA5y

Banggood GCRC
https://www.banggood.com/custlink/GmDmQ1nVkO

Here is a link to the Video:
https://www.youtube.com/watch?v=yyvvN5UknGI

I can't stop flying this Plane!
This is going to be an excellent 3D Trainer for me and it's a blast just doing these Slow, Graceful, Maneuvers with this Plane.
It's definitely worth the time to build.

Here is a link to the Playlist which also has the Assembly videos:
https://www.youtube.com/playlist?lis...CJXYC8MOVVzI6J

RC Tip #24 - Servo Setup & Centering - Get that Servo perfectly Centered
https://www.youtube.com/watch?v=RbfIs5O999E

This Yak54 Aerobat Kit is Courtesy of Banggood.
I want to thank Banggood for sending this Kit for Review.

Here are link to the Components I used in this Kit 3D Plane:

Yak54 3D Aerobat 800mm Wingspan Kit
https://www.banggood.com/custlink/mDKGw3NA5y

Servos - 6PCS Racerstar SG90 9g Micro Plastic Gear Analog Servo (I used some old EXI 9g Servos I had on hand)
https://www.banggood.com/6PCS-Racers...47791920140372

Motor - RacerStar BR2208 1400kv 2S-4S
https://www.banggood.com/Racerstar-B...47791920140372

ESC - Htirc Hornet Series 12A 2-4S Brushless ESC With 5V/2A BEC For RC Models
https://www.banggood.com/Htirc-Horne...47791920140372

Control Horns - 10X Rudder Servo Rob Angle Set With 1mm Chuck Screw For...Continue Reading
Posted by Rowhider | Yesterday @ 06:04 AM | 3,082 Views
Run of yesterday with my Top-Force evo in my little garden track

TAMIYA TOP-FORCE - VINTAGE RACING MODEL - GARDEN TRACK RUN (2 min 52 sec)

Posted by QuadifyRC.com | May 27, 2020 @ 06:21 PM | 9,221 Views
Hi Guys

I've written a step by step setup guide for the WL toys 144001 that has come out better than I was hoping:

https://www.quadifyrc.com/rccarreviews/wl-toys-144001-setup-3-things-you-must-do-before-you-even-turn-it-on

-Filled the diffs with grease, adjusting the turnbuckles and correcting the amount of fluid in the shocks. This will really improve handling and substatially increase the life of the diffs and shocks. Hope you find this useful



.

Posted by GroundControlRC | May 27, 2020 @ 07:34 AM | 11,688 Views


Review Part 4 - Yak54 Aerobat EPP 800mm Wingspan 3D Plane - Tips, MODs, Setup, Conclusion!

Yak54 Aerobat 800mm Wingspan Kit
https://www.banggood.com/custlink/mDKGw3NA5y

Banggood GCRC
https://www.banggood.com/custlink/GmDmQ1nVkO

Here is a link to the Video:
https://www.youtube.com/watch?v=S9kHCUvfBec

I'm very impressed with this Kit 3D Plane.
It has a lot of power, is graceful in the air, and a lot of fun to fly.
I highly recommend this Yak54 Aerobat EPP 800mm Wingspan 3D Plane.

***I incorrectly stated in the video that the Linkage Setup I have in place offers the most movement but not the best Mechanical Advantage. That is incorrect, the setup I'm using does not offer the most movement or least Mechanical Advantage, it is a compromise between the two.

Here is a link to the Playlist which also has the Assembly videos:
https://www.youtube.com/playlist?lis...CJXYC8MOVVzI6J

RC Tip #24 - Servo Setup & Centering - Get that Servo perfectly Centered
https://www.youtube.com/watch?v=RbfIs5O999E

This Yak54 Aerobat Kit is Courtesy of Banggood.
I want to thank Banggood for sending this Kit for Review.

Here are link to the Components I used in this Kit 3D Plane:

Yak54 3D Aerobat 800mm Wingspan Kit
https://www.banggood.com/custlink/mDKGw3NA5y

Servos - 6PCS Racerstar SG90 9g Micro Plastic Gear Analog Servo (I used some old EXI 9g Servos I had on hand)
https://www.banggood.com/6PCS-Racers...47791920140372

Motor - RacerStar BR2208 1400kv...Continue Reading
Posted by phil alvirez | May 27, 2020 @ 06:23 AM | 11,856 Views
see parts 1 and 2 at my blog
also there was control-line: you fly the plane attached to 2 thin cables that are connected to a handle, like a pistol grip. you aim higher, the plane climbs. aim lower, it dives. turn and turn. and you had to overcome dizziness.
once you did, then try loops. wing overs. fly inverted (signals are reversed). then more stunts.
there was a competition pattern, where you had a sequence of maneuvers.
there was also combat, where 2 planes flew at same time. there was a streamer attached to the tail, and you aimed to cut it. the closer the more points you got.
and there was speed too.
we had lots of fun.
here, we could control the airplane.
a new experience.
Posted by AdAstraPerAspera | May 27, 2020 @ 05:08 AM | 12,182 Views
Thank you to everyone who will respond now .How can I software configuration asymmetric aircraft like NASA AD-1. System info : Pixhawk 2.4.6 and one electric motor. I use ardupilot, Mission planner . One more question can you make sugesstion for flight control software.
Posted by Tazkiller85 | May 27, 2020 @ 04:51 AM | 12,341 Views
Yep Les Amis,
La famille Tinyhawk s'agrandit ! Voici donc le nouveau Tinyhawk II Freestyle de chez EMAX . LES ÉVOLUTIONS :
- la Runcam Nano 2 apporte une toute nouvelle clarté aux images et facilite donc le pilotage.
- Nouveau VTX amélioré avec une transmission de 25 /100 /200 mw pour une meilleure portée .
- Nouveau design de châssis pour une inclinaison de la caméra entièrement réglable par deux vis .
- Condensateur protégé
Sinon on retrouvera les moteurs 1103 7000kv associés aux hélices AVAN Rush 2.5 pouces qui donnent une bonne petite pêche à notre engin tout en gardant une très bonne autonomie de 4 à 7mn ! Le Tinyhawk II Freestyle vient donc compléter avec classe la gamme de produits Tinyhawk et fera certainement des heureux encore une fois. L' ESSAYER c'est l'ADOPTER !!!
... Bon Film à Tous et Merci de votre soutien .

EMAX Tinyhawk II Freestyle - Review Test Démo - Belle évolution ! (32 min 25 sec)


NOTATAZ : 18.5/20 BRAVO pour l'évolution ...

Niveau : Débutants et Confirmés
Les + : Résistant, Qualité d'image, Portée vidéo, Bons réglages d'origine, Facile à piloter, Autonomie ...
Les - : Récepteur SPI , VTX et moteurs propriétaires EMAX ( mais est-ce vraiment un défaut ? )

Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous :
- EMAX Tinyhawk II Freestyle ( Coupon bGhOnEy10 ): https://bit.ly/2LShdd0
- Batteries URUAV 450mAh X5 : https://bit.ly/3bYM9mp
-...Continue Reading
Posted by Tazkiller85 | May 27, 2020 @ 04:50 AM | 12,362 Views
Yep Les Amis,
Cinewhoop Freestyle... C'est possible ! Pour mon grand retour au GAMELLODROME, je teste aujourd'hui le SECTOR132 de HGLRC. Une bonne machine, bien équipée et bien réglée à la sortie de la boite. Ce petit 3 pouces vous permettra de vous initier à deux pilotages différents, le Cinewhoop et le freestyle donc chacun y trouvera son compte . Par contre, je relève un petit défaut de conception au niveau de la frame un peu fine et flexible et surtout au niveau des bras. Le reste est bien conçu et l'engin est très agréable à piloter. En bref, un bon petit appareil pour de la cinématique et en indoor mais un peu faiblard pour du freestyle un peu risqué ... Bon Film à Tous et Merci de votre soutien .

HGLRC SECTOR 132 4K - Review Test Démo and Crash - Petit vol en bonne compagnie ! (37 min 49 sec)


NOTATAZ : 16.5/20 Arbre, 1... Taz, 0 ! lol

Niveau : Débutants et Confirmés
Les + : Réactif, Précis, Très stable, Autonomie correcte, Réglages ok, Images propres, Prix intéressant.
Les - : Fragilité des bras de la frame au niveau des fixations moteur .

Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous :

- HGLRC SECTOR132 : https://bit.ly/2ySNBcT
- HGLRC SECTOR132 ( différents modèles ): https://bit.ly/2yhb5b6
- Lentille ND8 Caddx Tarsier : https://bit.ly/3g7wNzu
- Microscope Digital LCD : https://bit.ly/2ynmDK8
- Lampe loupe Flexible : https://bit.ly/3bPfoIk
- Ventes Flash RC : ...Continue Reading
Posted by aben71 | May 26, 2020 @ 09:22 PM | 13,796 Views
Hey all,

It's been a while since I've posted,got a little rant and or inquiring.
So I purchased some items from banggood over a month ago,during this pandemic I was leery to do so but ebay and amazon stuff I ordered shipped ok,longer than usual but understood.
Banggood has been weird though,items show shipped,tracking numbers don't exist,but they still got paid my over $400 in orders.
I know it's a mess in the world just curious if banggood has cashed out and ran with our money.
Posted by Dynam RC Detrum | May 26, 2020 @ 09:17 PM | 13,795 Views
Z3-FPV is a first person view flight controller applied on RC aircraft. The important data such as real-time altitude, speed, voltage, posture and distance can be shown on screen with the OSD function in Z3-FPV. The PMU(power management module) that supports 2-6S input can provide real-time data collection of battery voltage and current while providing stable power supply to the flight control, providing indispensable key information for FPV voyage. It can be applied on normal wing, fly-wing, and V-tail airplanes.

It supports five flying modes, when it controls the airplane flying after connected with receiver. The RTH mode can allow the aircraft to return to the take-off point safely under any circumstances. Under normal stability-enhancing mode, the stability of flight can be fully improved. Safe mode allows the aircraft to fly at a fixed altitude and directional stability. Aerobatics mode can lock the flight attitude to meet the aerobatic needs of players. Off mode (manual mode) allows the player to control the aircraft completely autonomously. And it can automatically switch back to the self-driving mode when the remote control signal is lost or out of control, allowing the aircraft to return to the take-off point safely.

Z3-FPV uses the original lever mode to enter the horizontal calibration, the triggering method is simple, no need to connect a computer, more convenient and faster

Features

1,OSD Information Display Function: Real-time Monitoring of Flight...Continue Reading