Posted by Bill M - RC | Today @ 01:09 PM | 44 Views
Hi fellow rc pilots & rc enthusiasts

NEW Hawkeye Firefly Micro Cam 2 review. This 2.5k HD video was made with the new Hawkeye Firefly Micro Cam 2 fpv action camera mounted on a SJRC F11 Quadcopter drone. A full review video of this great new box form factor camera to follow soon on this channel. Please select 2.5k (1440p) HD resolution in your youtube viewing settings to view this at this resolution.

You can get this Hawkeye Firefly Micro Cam 2 2.5K 1080P/60FPS 160 Degree Water-Repellent Recording FPV Action Camera here now:

NEW Hawkeye Firefly Micro Cam 2 review - 2.5k at 30fps HD video clip (4 min 48 sec)

Posted by reverse | Today @ 12:14 PM | 53 Views
The Spektrum protocol puts out a packet of data every 11ms. The packet holds 7 channels.

In 22ms mode, that means there are 7 x 2 slots available, 14 channels total. The first 6 of each packet are channels 1-12, and the last slot is used for the X-Plus channels (which makes it very obvious why they are up to 88ms latency).

In 11ms mode, there are 4 channels that are sent every time, and the remaining 6 channels come in 3's. It sends out 4 channels + 3 channels, then the next packet has the same 4 channels + 3 different channels. 4 + 3 + 3 = 10 channels max in 11ms mode.

The DX18 generates its data as 12 channels + 8 channels, where channels 11 & 12 are the same as X+1/2.

The DX20 generates its data as 12 + 8 also, but channels 11 & 12 are configured independently.

This is what the "DX18 Compatibility Mode" option is for. It lets you pick 10+8 or 12+8 mode.

Because the iX12 can import files from either one, or from a lower end DX, it can generate either mode as well. It's important to understand what you are getting the configuration from to know how it will behave. If you import from a DX18 or lower, it will most likely be in DX18 Compatibility Mode, generating channels 1-10 normally and using X-Plus data for 11 & 12. If you import from a DX20, if it's in 20-channel mode then channels 1-12 will be as you expected. It is done this way because the purpose of importing a file from another type of radio is to make it so that the new radio controls the old model exactly the same way. You want your new radio to fly the plane the same way as the old radio, not change channel assignments on you.

Opalix didn't understand that part and assumed that the DX8 file he imported would automatically go into the 20-channel mode. It doesn't do that because a DX8 works in DX18-compatibility mode for channel generation (but you can't get there on the menu). He's got it all straight now (we've been working with him for several weeks through Product Support and PMs).
Posted by geileraupe | Today @ 08:02 AM | 99 Views
My newest mod on the FS-i6 Ball bearing hall sensor gimbal ... low budged -- fast and easy
FS-i6 Kreuzknüppel Hallsensor umbau (4 min 3 sec)

Posted by frank4wing | Today @ 02:37 AM | 150 Views
In this video I used different filters for the sound in the edit but I did not touch the image quality which looks quite good to me. You'll find the changed settings, a link to the firmware and other stuff in the video description if you're interested.

I wish we could have a better FPV image quality with these cameras though. Flying safely near trees with lots of leafless branches is still a matter of luck.

Armattan Gecko, Caddx Turtle (3 min 57 sec)

Posted by Blaze0021 | Yesterday @ 11:12 PM | 168 Views
I don't normally do videos dubbed to my flights, but I thought this was fitting.

Disclaimer - So if you don't like videos like these, just move along.. this was 100% for me and not for you, not for views, and not for ratings. And please keep in mind, all of the planes in my fleet are 100% purchased by myself. I don't have vendor sponsors, and I do not monetize or profit from any of my videos. In truth, a lot of my videos are meant as a personal flight journal of the aircraft I've flown throughout this great hobby I've enjoyed for the past 6 years.

However, if you don't mind flight videos to music, please sit back and enjoy the show.

Durafly EFXtra 975mm Wingspan Racer - Adventure Club "Gold" Music Video (4 min 40 sec)

The Queen of my Fleet, she is still the fastest and ranks as "Legendary" out of the 90 aircraft I own. Some say she can be difficult to handle and requires the pilot to be several steps ahead of the flight, but to me it was more like seeing an old friend and I don't find anything difficult about her at all.

I had to clear my head today and take her out again for some flights. Still every bit as legendary as when I first flew her in this video.

Music: Adventure Club "Gold" ft. Yuna

Thanks for watching!
Posted by AGFRC | Yesterday @ 09:54 PM | 173 Views
If you are looking for a high quality and reliable servo but good price, you got the right one here. AGFrc A80BHMW super torque waterproof steel gear digital servo will be the great option which support to use with high voltage and damp situation. A80BHMW servo make almost 500oz-in torque with speed 0.11sec at 7.4V. While using voltage up to 8.4V, it can deliver 555oz-in super torque and 0.085sec high speed at 8.4V. Perfect for scale crawlers, 1/8 1/10 monster truck, 1/8 1/10 2WD and 4WD buggies, as well as 1/8 scale buggies and trucks. In addition, this A80BHMW is great choice for boats and other application which require high power, high voltage and waterproof servo.

This A80BHMW is waterproof IP67 level up to 1 meter which allow driving in the rain, puddles, snow and mud. High reliable and durable patent gear design which can be longer service life. Full aluminun CNC case for fast heat disppation. High precision digital control circuitry. If you need some modification based on our default setting, pls contact us directly

Operating Voltage: 4.8-8.4 V
Operating speed: 0.120sec/60 @ 6.0V
Operating speed:0.100sec/60 @ 7.4V
Operating speed:0.085sec/60 @ 8.4V
Stall Torque: 31 kg-cm (430.51 oz-in)@ 6.0V
Stall Torque:36 kg-cm (499.95 oz-in)@ 7.4V
Stall Torque: 40 kg-cm (555.50 oz-in)@ 8.4V
Gear: Steel
Motor: BLS
Size: 40*20*37.2mm (1.57 x 0.78 x 1.46 in)
Weight: 79g
Connector Wire: JR 300 mm

More details about this servo, check here

Posted by Adrian_ | Yesterday @ 11:20 AM | 310 Views
When thinking about the pros and cons of vertical arms this idea striked my mind: Combine vertical and horizontal arms to form a T-Beam. I started designing a frame for a 4" ultralight (<250g all-up-weight) with easily interchangable arms, minimal weight and maximal durabiliy in mind. Ok, fair enough, this is probably the goal for most frames out there, but I think this approach is pretty different and I'm quite happy with how it turned out! The T-Beams give the frame an incredible amout of stiffnes and good durability, especially considering the weight of only 33g. And most importantly the design is completely open-source, you can take a look here. Edit: I just realized you need to create an account to watch it :/ But it's worth it

This frame allows you to build a Quadcopter with 1407 Motors, 20x20mm Stack, Micro-Camera and a 4S 800-850mAh Battery under 250g AUW! It has an insane amount of power and feels really agile in the air. I used the Rotorgeeks motors and HQ 4x4.3x3 V1S. This is a perfect combination I think and those props are just awesome.

A few notes about the design.
-The T-Beams should be glued into the arm with epoxy
-The Top-Plate is held in place by rubber bands/big O-Rings using eiter the hooks on top or a little furter down. Initially I used long screws which went alls the way through the frame but then dropped this idea because it was just not practical. However, if you like to, you can just load version 0.10c in Onshape. I also attached...Continue Reading
Posted by GiantPowerLiPos | Yesterday @ 08:08 AM | 317 Views
One pair of 7.4v PH type UMX plugs with leads. This is the plug used by Horizon Hobby on all the UMX 2S 7.4v lipo planes and helicopters. You get a set of 1 male and 1 female pig tail. The wires are just over 4" long and are soft silicone 22 AWG. This item has male plug that goes to ESC or charger (device side) and female plug that goes to battery pack. Perfect item for repair or customization of your small RC air craft using 7.4v light weight UMX batteries. $5.99 per set of 2 (male/female).
  • Pair of pig tails, one male one female
  • Soft 200 deg C 22AWG silicone wire 4+" long
  • High quality materials
Posted by jmxp69 | Yesterday @ 03:05 AM | 672 Views
I always like to see what kind of power my planes make. The BAe makes some impressive numbers.
Freewing BAe Hawk Watt Meter Test (6 min 36 sec)

Posted by GBLynden | Apr 20, 2019 @ 11:57 PM | 792 Views
This is my Blade Scimitar 110 FPV Quad BNF Basic FPV Maiden Flight.

Blade Scimitar 110 FPV Quad BNF Basic FPV Maiden Flight (5 min 3 sec)

Blade FPV Quad Review Notes:

- Runs on 2S or 3S lipo packs
- Comes professionally pre-tuned out of the box
- Includes spare props and prop tool
- It is easy to setup with the manual
- There are different VTX power settings
- You can program the VTX settings with your radio or by pushing the button on the quad.
- The video quality is great via my Fatsharks
- It had a price reduction recently, so the price is only slightly more than the Blade Torrent 110 FPV Quad at the time I made this video.

- There are only three camera angle settings separated by 15 degrees with a maximum angle of 30 degrees
- The antenna pops out and moves side to side way too easy. I may be modding that with rubber tubing or hot glue.
Posted by old4570 | Apr 20, 2019 @ 11:53 PM | 481 Views
Sorry Guys !

Mini Surfer 800 is on hold for the Victorian Control Line State Champs ...

My back can only take so much activity and I am spending it all going to the state champs and taking some pictures .. ( Saturday F2C Final ) ( Sunday Vintage Combat )

Sure wish I could have stayed longer ...
Posted by Frogster7 | Apr 20, 2019 @ 09:34 PM | 525 Views
Rain Rain Go Away. I have Plans Tomorrow to go Flying as you can see. So many choices to choose from. So much fun to be had. Hope everyone is enjoying their Easter Weekend. Happy Flying to all.
Posted by Shoveopoly | Apr 20, 2019 @ 06:46 PM | 440 Views
Got the purple Robocat back together, and flashed with Ardupilot. If it ever stops raining, will take it for a test flight.
Posted by Bill M - RC | Apr 20, 2019 @ 06:00 PM | 467 Views
Hi fellow rc pilots & rc enthusiasts

Eachine Tyro109 review Full Build & assembly step-by-step guide. This Eachine Tyro109 210mm DIY 5 Inch FPV Racing Drone PNP w/ MatekF405 F4 FC, 30A Esc, 600mW VTX & Caddx Turbo Eos2 1200TVL Camera build video is long, but shows every step of the process required to assemble this and includes tips & advice during this process too. This is to show anyone interested in building this Eachine Tyro109 or their own first freestyle or racing fpv quadcopter drone how this is done, and to assist make this build easier for anyone that purchases this. I hope you find this informative & helpful.

You can get this Eachine Tyro109 210mm DIY 5 Inch FPV Racing Drone PNP w/ MatekF405 F4 FC, 30A Esc, 600mW VTX & Caddx Turbo Eos2 1200TVL Camera here now:

Limited offer coupon: RC9OFF
expiry date: 2019-04-23

Eachine Tyro109 review – Full Build & assembly step-by-step guide (59 min 22 sec)

Posted by Pieter Bot | Apr 20, 2019 @ 04:12 PM | 458 Views
It was a beautiful day in the Netherlands.
Today the Chica had his maiden flight. For this i get some help from TvM. After the trims are set, i got the controles.
It is a bit exciting, but the Chica flies well. See the photo of the Chica.
Now i can think what will be the next project.
Br Pieter Bot
Posted by GroundControlRC | Apr 20, 2019 @ 01:41 PM | 630 Views
DustOff #1 - Glue & Fly Series F22 Micro V2.5 - Way too much Fun!

Here is a link to the Video:

Well, I'm exciting about Blowing the Dust Off of this Mini Parkjet!
The Plans for this Parkjet will be uploaded to Patreon soon.
I haven't flown this Parkjet since completing the Development of the V3.
Let's blow some Dust Off!

See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

See Us On Youtube | Patreon | RCGroups | Facebook
Posted by zoltansgarage | Apr 20, 2019 @ 01:31 PM | 499 Views
Thrust bearing detail.
Posted by zoltansgarage | Apr 20, 2019 @ 01:26 PM | 497 Views
The start of the running gear. The stainless steel rod was smaller than the hole in the propeller.
Flattened it out a bit, and threaded it. Added some silver solder to hold in place. Made a thrust bearing washer from a hard nylon type material servo arm.
Posted by Krashcan | Apr 20, 2019 @ 01:01 PM | 497 Views