burkefj's blog View Details
Archive for January, 2014
Posted by burkefj | Jan 27, 2014 @ 01:53 PM | 11,724 Views
I've been going through my old designs/plans and slowly re-doing them for public consumption, originally I did an F-8U-III super crusader which was basically a similar design except for the nose and intake. I decided to make it a straight crusader this time. You could take these patterns and make a pointy nose and curved intake snout and re-do it as a super crusader. There are slight wing differences but probably not enough to notice. On the super crusader you'd have to figure out a way to model the ventral fins which are either horizontal or vertical and quite large, on mine I just created some ventral strakes that sort of modeled them from the side view in takeoff position.

I used a center piece with tail and then two doublers on each side to give me enough thickness to give a nice rounded nose and intake.
It would be easy to add some formers or pink foam and add thickness to make it fully 3-d.

Originally I mounted the wing on the top of the fuse with some tabs and glued a fairing cover over the top. On this version, since the real plane has some airfoil thickness, I decided to pick the most forward point of the wing leading edge and use that for the slot location. I think it looks ok like this and allows some foam above the wing to hold it in place and model the fairing that is on top of the wing. In order to lock the wing in place, I'll drive some 2" pieces of 1/8" carbon rod down through the top of the fuse through the wing and into the body and...Continue Reading
Posted by burkefj | Jan 17, 2014 @ 02:13 PM | 11,537 Views
I decided to do another Phantom build, make a few changes to the original and plans. I originally did these because there weren't great simple plans for a phantom at the time. I'm not a big fan of mid mounted engines or box fuses, I'd rather have a slim profile, gives less drag in the air and is quieter. It does require you to mount equipment on the bottom of the wing has the battery mounted on the front side of the nose, but I'm ok with that. Due to the thin profile the wing hits the fuse further forward than on a normal fuse. If desired, you could alter the top view of the wing to include the intake profile and nozzle profile on the rear of the wing so that the top view was more representative, I considered this and decided to leave it clean. If you do this you may need to do some glide tests to confirm CG did not shift as the intake profile will add forward wing area. The wing is not mounted on the bottom, but is in a slot, I did this to give a bit of area under the wing to mount the electronics and not get destroyed on landing.

Flight video at:
F-4 Phantom parkjet flight 1 (4 min 18 sec)


Here is the Rocket boosted flights...

F-4 phantom scratch built parkjet/rocket boosted glider (2 min 0 sec)
...Continue Reading
Posted by burkefj | Jan 13, 2014 @ 01:41 AM | 10,118 Views
While recovering from my foot surgery, I was watching all sorts of youtube videos on F-105's etc.....Then I realized I don't have any enemies for my thud. I decided to go back to my original Mig 21 profile and change it to a cruciform style instead of a true profile fuse...This saved a bit of weight, but meant the CG would have to move forward a bit. It did give more surface area though so the wing loading would decrease. I went back to my mig thread and saw some pictures a guy had done with panel lines so I went that route. Looks like rtf it will be about 11.5 oz. Did my normal rocket motor mount so I can do rocket glider or with my pusher pod installed.

I went with Czech markings as I have some bohemian in my blood....

Maiden went well, was a little too nose heavy, so removed some weight and it flies really nicely, was a bit windy today.

Mig 21 profile pusher RC parkjet (3 min 42 sec)


Frank
Posted by burkefj | Jan 06, 2014 @ 07:36 PM | 10,628 Views
I discovered that the evergreen aviation museum has a thunderchief now on display....It was a nice sunny day so I took some photos....didn't take me long to decide to upscale my original 3mm micro version to 6mm and 39" long...Kinkos did the scaling for me from my original plans. I decided to use a doubled central fuse with two side doublers, and 3mm covers over the rocket mount that also doubles for mounting my grayson microjet motor. Plane is already framed up awaiting an esc and maiden to confirm the CG. I stuck with a full flying tail only. This is a single seat D version. Not sure on the colors yet, I'll probably go with the light bottom and camo top like these photos..... Here are some pictures from Evergreen.....The original small version, and my newer version.

Update 1/7 Finished the painting, now just need to do some panel lines, a few letter markings and wait for my ESC.

Update 1/8 Finished the markings and panel lines, esc is in today but rain for the next week Looks like right around 14 oz rtf.

Update 1/13 Maiden went well, CG was right on, was very windy today but handled it well.

Video will be at:
F-105 Thunderchief RC parkjet (2 min 17 sec)


...Continue Reading
Posted by burkefj | Jan 06, 2014 @ 05:58 PM | 10,058 Views
F-106 Delta Dart Kit weight RTF is 10-12 oz for the aerotech reloadable 24mm E-6, D-7, e-7 rc reloads and Estes D-11P, D12-0* and E12-0*. These kits are hand cut and fitted.I'm doing a lot of the work for you, Fuselage sides are laminated with a carbon nose reinforcing, wing spars are pre-slotted, Elevons are pre-hinged. The motor mount is pre made. The joints are pre-taped so you unfold them, apply CA+ to the joint and they are ready to be assembled...As an option the kit can include a pre-built adapter that clicks into the 24mm rocket mount and has a ply plate that allows you to mount a pusher electric motor so that you can convert from rocket to electric in a few seconds. Basic steps and instructions for download are shown below, basically the steps are gluing pieces together and taping.

For ordering or more information go to
www.dynasoarrocketry.com

Included:

Airframe pieces with carbon spars, elevons (pre-installed)
Control Horns
Nose weight
Pushrods
Motor mount
Rail buttons and screws or launch lug(your choice)
styrene strip for reinforcing
velcro for mounting rx/bec/battery
blenderm tape(for taping wires and reinforcing joints)

*(Estes motors require a small amount of epoxy to be placed in the front of the motor so that the motor is not ejected and does not damage the foam) . This is not a manufacturer approved change and is not allowed by NAR rules but is an option if you are launching in your own field....Continue Reading