Shop our Airplanes Products Drone Products Sales
Posted by BarnOwl | Today @ 06:04 PM | 27 Views
Recently I got myself an ASW 28 glider, a Grand Tundra and the latest Spitfire 1450mm as toys. I have not flown the Spitfire yet as I still have to finish the build but it is my only warbird and a beautiful one.......
Posted by Galox | Today @ 04:20 PM | 79 Views
CADDX Turtle V2 Camera 1/2.7 Inch 800TVL NTSC / PAL Changeable CMOS Sensor FPV Camera For Remote Control Toy RC Helicopter Car
❇️ New item in AliExpress
💰 Price now $48
🚙 free shipping
🏆 The best price
http://rcsearch.info/wa/1414205

I invite you to the blog, which publishes the best prices, discounts, coupons for current RC-products in dozens of stores around the world.
Get the best deal: http://rcsearch.info
Telegram: https://t.me/rcmarket_eng
Facebook: https://www.facebook.com/FPVMarket
Posted by Jim.Thompson | Today @ 04:19 PM | 70 Views
The advantages of this method are:
1. Light and strong.
2. Ease of construction.
3. Quick and cheap. Foam for the ribs can often be found from recyclers.
4. Accuracy. All ribs cut together in the one set up. Cannot get them better aligned than that.

For my next constant chord wing using this method, I plan to construct the spar first. It will go something like this:

1. A foam core tapered in thickness will be hot wire cut. Dimensions will be the airfoil thickness minus the carbon caps, minus 1 mm for sanding/fairing balsa. Lets say, nominally 35 mm high and 8mm tapering to 4mm thick, (for example sake only).
2. This core will be faced in 1 mm Pauwlonia ( but could be balsa or basswood et. al.) with vertical grain orientation.
3. End grain of the timber is then sanded down to the foam.
4. Pre-made carbon spar caps are then added to the top and bottom of the assembly. These will be layed up using common uni-carbon/laminating epoxy which is cheap.
The thickness of these caps are tapered out to the tips.
5. The caps are glued on and the assembly wrapped with Dyneema, Kevlar, or other similar high strength braided line. Then all given a light application of thinned epoxy resin.
6. The "laser method" hot wire cut ribs are cut with a slot to take the spar. The building board might be in two parts, to enable separation of the two halves to allow the spar to be lowered into place, glue applied, then the two halves brought together.

I fully expect this assembly to be super strong and super strong.

Video of a top cut:
Top cut left wing (1 min 35 sec)

Posted by RocketMouse | Today @ 03:28 PM | 93 Views
Connections:

Home button to PWM5.
Select button to PWM6.
Display to I2C port
Bluetooth to UART1
Local GPS to UART2
http://seriouslypro.com/files/SPRaci...ual-latest.pdf

Flashing:

1. Short bootloader pins (Boot headers (11) - check pdf from link above), connect Usb.
2. Using Betaflight or Cleanflight configurator in Chrome upload SPRACINGF3_**.hex FW from here https://github.com/raul-ortega/u360gts/releases

Configuration:

1. Download and install Configurator from here https://github.com/raul-ortega/u360gts-configurator
2. Run Configurator from Chrome Apps. Select Com port, select Bauds 115200, press Connect. Press CLI ENTER. Now all parameters should get loaded. Set in settings PROTOCOL to Autodect, and set BAUDRATE same as your bluetooth or radiomodem speed. I use 57600 for Mavlink. Press SAVE. To connect again to Configurator set Bauds to 57600 at the top.

Tip: Uart1 is in parallel with Usb, and it means telemetry is not coming in when Usb connected. You can connect a Bluetooth module to uart1. Usb is only useful for flashing new versions. You can, may and should configure/tune the tracker «wirelessly».

If not set by default, run the following command in CLI mode to be able to use the local gps function through serial port 1 (UART2):
serial 1 2 38400 38400 0 115200

Other settings should be like this for Ublox GPS:
set gps_provider=UBLOX
set gps_sbas_mode=AUTO
set gps_auto_config=ON
set gps_auto_baud=ON


On screen info for local GPS:
RX: received packets
ERRs:...Continue Reading
Posted by fastmax | Today @ 12:58 PM | 157 Views
My Remo Hobby 1093-ST arrived over the weekend, and I am super excited about this truck. It looks great, and seems to be a very nice quality truck for the price. I haven't had a chance to run it yet, but the battery is charging now, and I will get it out for a test drive this afternoon.

Check out the pics, and stay tuned for more info, and running video coming shortly.

This 1/10 Scale Ready To Run Scaler/Trail Truck is now on sale here for $149.99 during the Christmas sales going on now at Gearbest.

Printing some scale accessories while I wait for the truck to arrive. Propane tank, and some other cool stuff can be found here. Wheel hubs can be found here. The shackles can be found here....Continue Reading
Posted by Ethan Ater | Today @ 12:29 PM | 151 Views
It’s finally here! The game changer in EPP biplane 3D madness

TwistedHobbys / Hacker Model Pittsbull Teaser (1 min 38 sec)

Posted by Prof100 | Today @ 12:25 PM | 144 Views
Enjoy. Been around for quite a while. 2009 video. Enough power and you can fly a pair of gym socks.
Dirty Old Sock Parkflyer (0 min 31 sec)

Posted by Pierre_de’ Loop | Today @ 11:39 AM | 176 Views
The parts for the left side of the wing have been cut out and made ready assembly. No word from BUSA yet but I'm feeling better about the results on the right side. I haven't run across any online pictures of Taube bones that look substantially different than mine. I figure that means I'm on the right track.
Posted by japim | Today @ 10:48 AM | 196 Views
A friend of mine finished his Me 109 model from 3D Lab Print.
He was a very good R/C Combat flier, but haven't flown for couple years already.
Me 109 from 3D LabPrint was supposed to be his come back.
Weather was very bad for flying - rain + wind. White model on grey sky.
But he was very determined to make the maiden flight either way.

Maiden was OK.
Second flight was not so much OK...
3D LABPrint Me109 maiden + crash (3 min 4 sec)

Posted by basslord1124 | Today @ 09:33 AM | 223 Views
Just recently did my first livestream on my channel Perkyplanes & RC. Here's the full video:

Perkyplanes & RC First Livestream! (1 hr 18 min 56 sec)

Posted by scousethief | Today @ 07:50 AM | 286 Views
https://www.banggood.com/Diatone-201...p-1395006.html



Diatone 2019 GT R249 HD Edition 95mm 2 Inch 4S FPV Racing RC Drone PNP w/ Mamba F4 OSD 25A Dshot600 RunCam Split Mini 2 TX200U

Diatone 2019 GT-Rabbit R249(R90) 2inch HD FPV Racing Drone PNP F4 8K OSD 20A Blheli_S ESC RunCam Split Mini 2

Receiver plug port - Frsky R-XSR JST1.25


Specification:
Brand name: Diatone
Item name: GT-Rabbit R249(R90) 2inch 3-4S
Color: Bla/White/Transparent
Fury F4 OSD 8K flight controller: MPU6000 Six-Axis; OSD; 16M Flash; 5V 2A BEC;
Camera: RunCam Split Mini 2
VTX: Runcam TX200U VTX

Parameter

Model RunCam TX200U
Frequency Channel 5.8G 48CH
Output Power 25mW / 200mW
Working Current 5V@150~400mA
Voltage out 5V@max 250mA
Voltage in 1S 3.5-5.5V
Video Input Impedance 75 Ohm
Antenna U.FL 5.8G 2dB Omni antenna
Weight 2.5g (with antenna)
PCB Size 19mm*19mm

ESC: F25 20A Current Sensor 3-4S
Motor: Mamba racing 1105 5500KV 3-4S
Propeller: 2 inch

Please note:
The PNP (Plug and Play) version comes without battery, charger, receiver or remote control.

Package included:
1 x 2019 GT-Rabbit R249(R90) 2inch HD Version


-------------------------------------------------------------------------------------------------------------------------------------

https://www.banggood.com/Diatone-2019-GT-R249-95mm-2-Inch-4S-FPV-Racing-RC-Drone-PNP-w-F4-OSD-25A-RunCam-Micro-Swift-TX200U-p-1377959.html



Diatone 2019 GT R249 95mm 2 Inch 4S FPV Racing RC...Continue Reading
Posted by frank4wing | Today @ 06:06 AM | 329 Views
Another frankensteined XJB-145, this time in a GEPRC MX3 frame with a Mobius Mini mounted to the top. The Mobius is a little gem that makes a brilliant picture and has a nice software to configure it.

XJB-145 & Mobius Mini, First Take (3 min 29 sec)

Posted by Galox | Today @ 05:04 AM | 338 Views
2pcs Foxeer Lollipop 2 Stubby 5.8GHz 2.5Dbi RHCP/LHCP FPV Antenna SMA for RC Drone-Fluorescent Green

❇️ New item in Banggood
💰 Price now $20
🚙 free shipping
🔖 With coupon E2BCEA the price is $20 for 2 pcs. ($9.95 for one)
http://rcsearch.info/wa/1406270
⏳ Preorder!

I invite you to the blog, which publishes the best prices, discounts, coupons for current RC-products in dozens of stores around the world.
Get the best deal: http://rcsearch.info
Telegram: https://t.me/rcmarket_eng
Facebook: https://www.facebook.com/FPVMarket
Posted by Galox | Today @ 05:02 AM | 339 Views
Foxeer Predator V3 16:9/4:3 PAL/NTSC Switchable 1000TVL WDR OSD Mini FPV Camera Fluorescent Green - 2.5mm
❇️ New item in Banggood
💰 Price now $42
🚗 + shipping $1.3 = $43
🔖 With coupon E2BCEA the price is $43
http://rcsearch.info/wa/1406268
⏳ Preorder!

I invite you to the blog, which publishes the best prices, discounts, coupons for current RC-products in dozens of stores around the world.
Get the best deal: http://rcsearch.info
Telegram: https://t.me/rcmarket_eng
Facebook: https://www.facebook.com/FPVMarket
Posted by Galox | Today @ 05:00 AM | 343 Views
RunCam Racer 2 Super WDR CMOS 700TVL 1.8mm/2.1mm FPV Camera 6ms Low Latency Joystick or UART Control
❇️ New item in Banggood
💰 Price now $38
🚗 + shipping $1.13 = $39
🔖 With coupon E2BCEA the price is $33
http://rcsearch.info/wa/1410181
⏳ Preorder!

I invite you to the blog, which publishes the best prices, discounts, coupons for current RC-products in dozens of stores around the world.
Get the best deal: http://rcsearch.info
Telegram: https://t.me/rcmarket_eng
Facebook: https://www.facebook.com/FPVMarket
Posted by myrcmodel | Today @ 03:49 AM | 356 Views
ARRIS X280 280mm aims at long range and long flight time for drone fpv lovers. It is compatible with GoPro and sports camera on top. With the GPS, it can realize the one key return to home function. With 600w stock video transmitter, the transmission range can reach to 2km. With the Frsky R9M + R9MM receiver, the control range can reach to 10km.With 3s 5000mah lipo battery, the hovering time can reach to 24minutes.


Specifications:
Diagonal Wheelbase: 280mm
Flight Controller: F4 Pro V3 flight Controller
Motor: X2206 1500KV
ESC: BLHeli_S 30A
Frame Material: Pure Carbon Fiber
BNF weight: About 356g
Camera: Foxeer HS1177 V2 camera
FPV TX: 5.8G 48CH (0mw/25mw/100mw/200mw/400mw/600mw Switchable)
Antenna: 5.8G pagoda Antenna

For more information, you can check https://www.arrishobby.com/arris-x28...gps-bnf-p-4162