mikejr83's blog View Details
Posted by mikejr83 | Aug 08, 2019 @ 08:55 PM | 1,702 Views
This is probably the hardest step. It's not technically difficult, but cutting holes in you brand new center panel can give you a bit of the hand shakes.

As with any task a little prep before can make the task much easier. Going back to the tools that I listed out in the earlier posts you'll want to have that diamond tipped cutting bit and a conical stone sanding bit along with your Dremel. You'll also need scissors, a felt-tip pen, a hobby knife, some scrap balsa sheeting, the top of a servo case (clear plastic will work), and one of your clevises.

Name: MVIMG_20190808_170442.jpg
Views: 0
Size: 942.9 KB
Description:

Cut the top off a case containing a servo. Most servo cases are clear so this generally is a good place to go to get a piece of plastic. Get a ruler and measure 2cm from the edge of the plastic. Place a dot there. Now take the ruler away and place your clevis so that its tip is on the dot. If the other end goes off the plastic that's ok. Make sure the clevis is sitting so that the pin would be parallel to the surface of the plastic, basically in the same position it would be as it was exiting the wing. You'll now take the felt-tip pen and draw a line around the clevis. The outer edge of the line should extend at least 2m, the width of the tip of the pen, from the clevis. Next remove the clevis and color in that whole area.

Name: MVIMG_20190808_170653.jpg
Views: 0
Size: 938.3 KB
Description:

You can now position this on your upper wing skin to see how the hole will look in the skin. Don't be too concerned. You haven't cut anything yet.

Now time to cut! The plastic! Cut out the...Continue Reading
Posted by mikejr83 | Jul 20, 2019 @ 09:17 PM | 3,449 Views
In this post I'll be discussing getting the wing prepped for servo installation.

The Wing - Prep

I start working on the wing first. I like to get this out of the way first. The wing is the most complex part of the build. Spending time getting everything right here will ensure that your model launches true, holds trim and flies right, and lasts for many years. The key to achieving this is having good tight, zero-slop control surfaces along with correctly aligned push-rods. The following steps will help you prep the wing for the servo install.

I use lots of blue painters tape to write mark spots on the wing as well as to protect the surface. You may find that your tape doesn't stick well. This is because there may still be some mold release on the surface. As a general first step I wipe down the wing surface with isopropl alcohol. This also gives you a good opportunity to caress and love your model .

The next step you take is to stabilize the control surfaces. Most likely when you got the model out of the box NAN had the edges taped so that the ailerons and flaps wouldn't move around during shipment. It's best to go ahead and reinforce this a bit. I put about 15 cm (6") of tape on either side of top of the wing along the skin so that the tape overlaps the aileron or flap and the wing. Make sure to do the control surface is in a "neutral" flight position, like cruise. It isn't important to be exact you just want the aileron or flap to be in a...Continue Reading
Posted by mikejr83 | Jul 20, 2019 @ 08:35 PM | 3,331 Views
I decided to track my Xplorer X3, 2019 edition, build here instead in a public thread. In a number of posts I'm going to try to cover in-depth the manner in how I approach building this model. The first time I tackled this it was very intimidating. Luckily I have access to some top notch pilots and builders, Jody Miller and Jeff Duval. Both of these guys have build tons of Xplorers and know how to get them built and setup to win contests. Hopefully I'll try to best pass along tips and tricks that I've learned so that anyone reading should be able to build one of these models with confidence. This first post will cover getting things ready.

Getting Your Model

First things, first. Inspect everything you have. Do this before you sign for your model from the shipping company. In the USA our NAN dealer is Soaring USA. They pack their models for shipping in probably the best possible manner. Everything is bagged, wrapped in bubble wrap, covered in foam, and taped down. The box even has a 2x2 running down its back so it can't get compressed. Even still, shipping companies, I'm looking at you FedEx, can still come up with some creative ways to damage items.

Name: mvimg_20190716_075315.jpg
Views: 0
Size: 2.03 MB
Description: You can see how the creases and holes match up. Inspect your models before signing for them!

The box on the left was delivered to my residence in December of 2018 and the box on the right is the latest in July of 2019. You can see how FedEx has some piece of machinery that has placed creases and holes in the same spots. The more heavily damaged box on the left contained my extremely fragile NAN Explorer Big...Continue Reading
Posted by mikejr83 | May 28, 2019 @ 09:15 PM | 1,574 Views
This past weekend I competed in a F5J event as the warm-up to the TD contest at the Mid-South Soaring Championships.

My goal was to launch to 100m for each round.

Flight #1
Name: MidSouthFlight1.png
Views: 0
Size: 46.1 KB
Description:

Flight #2
Name: MidSouthFlight2.png
Views: 0
Size: 40.7 KB
Description:

Flight #3
...Continue Reading
Posted by mikejr83 | Jan 04, 2016 @ 09:37 PM | 16,670 Views
I finished my Sbach 342! Read all about it!