Comments (7)
Add Comment
-
Views: 323
1/3 scale BalsaUSA custom-built laminated tail -
Views: 307
1/3 scale BalsaUSA custom-built laminated tail -
Views: 298
1/3 scale BalsaUSA custom-built laminated tail -
Views: 299
1/3 scale BalsaUSA custom-built laminated tail -
Views: 279
1/3 scale BalsaUSA custom-built laminated tail -
Views: 291
1/3 scale BalsaUSA custom-built laminated tail -
Views: 285
1/3 scale BalsaUSA custom-built laminated tail -
Views: 301
1/3 scale BalsaUSA custom-built laminated tail
-
Views: 280
Covering the plans with Freezer paper (or wax paper) -
Views: 243
I am using the Freezer Paper shiny-side up. -
Views: 241
Here is the balsa building board. The back of ceiling tiles works well too. -
Views: 240
Using pins on the sides to secure a part of the old tail that i plan to reuse. It is two strips of balsa with carbon fiber in middle, glued with 5min epoxy. -
Views: 245
Various types of "T-pins" -
Views: 254
A box to keep pins sorted. This is enough to build a 40% plane! -
Views: 246
Closeup of pinning technique. Pinning through wood causes a stress crack in wood. Sides are better. -
Views: 254
Closeup of horizontal tail trailing edge with CF going into dowel.
-
Views: 749
Custom painted Multiplex "Fun Cub" -
Views: 534
Stock Multiplex "Fun Cub" -
Views: 579
I found a paint scheme i liked. Aviat Husky A-1C -
Views: 611
Here are some of my painting supplies. IWATA Eclipse HP-BCS paint gun, cleaning pot, Createx paints and cleaner. -
Views: 518
DANGER! Only water-based paints only. Box fan with 20x20 pleated filter to catch overspray. Fan on low. -
Views: 513
Dewalt "Oil-less" air compressor. Regulator set between 40-60psi. -
Views: 486
Auto paint supply masking paper and 3M auto masking tape. -
Views: 507
Createx t-shirt craft paint cleaner.
-
Views: 606
FoamBusters Feb 22, 2010 -
Views: 458
Great planes & friends! -
Views: 512
Parkmaster midair with TaxiCup and I wasn't flying either one. -
Views: 8957
I did test flight and radio setup for fellow FoamBuster. Easy flying plane. -
Views: 461
Taking about planes. -
Views: 455
Surely taking EDF jets... -
Views: 418
Flying at the dam in December.
-
Views: 2383
Multiplex Park Master 3D EPP first airbrush attempt. Fun! -
Views: 1015
Multiplex Park Master 3D EPP using Createx primary color paints -
Views: 877
Multiplex Park Master 3D EPP attempt at flames -
Views: 934
Multiplex Park Master 3D EPP bottom -
Views: 732
Multiplex Park Master 3D EPP ghost flames -
Views: 1026
Axi motor with cooling fan.
-
Views: 529
A great day at Chilhowee Soaring, Benton, TN 2007 -
Views: 461
Bucker Jungmann & Aeronca Champ in hangar at Old Goat Aerodrome, Franklin, TN -
Views: 512
Bucker overnight camping trip to Chilhowee Oktoberfest 2007 full-scale glider meet. -
Views: 503
Giving a few rides to friends at Chilhowee Gliderport 2007 -
Views: 447
Me giving rides in german 1957 Schleicher Ka7 Rhönadler sailplane. -
Views: 469
I also gave rides in the 1960's vintage Czech Blanik L-13 at Chilhowee TN Oktoberfest 2007.
-
Views: 653
Joe Nall 2008 -
Views: 414
Cubzilla!! Aiiee!! -
Views: 389
Monocote covered custom built cowl. Modeled after the 180hp pa-18 -
Views: 385
First flight and engine break-in. Several light aerotows after test flight. Zenoah GT-80. -
Views: 351
Cowling installed -
Views: 394
Peeler Park. Nashville, TN -
Views: 389
Finally finished! -
Views: 413
Original install with several modifications to firewall. Stock mufflers and break-in prop.