Model Number 9080101
Continuous Current 80A
Burst Current(10s) 90A
Battery NiXX/Lipo 5-18NC/2-6Lipo
BEC Output 5.5V/5A
Length 68mm
Width 37mm
Height 14mm
Weight 118.5g
User Program yes

more info: http://www.ztwshop.com

ZTW Beast SS 120A brushless ESC for 1/8 cars.

source from http://www.ztwshop.com

It’s more about the performance, it is about the fashion. It’s about competition. Our team has been dedicating lots of time and efforts to improve the design to bring you this completely stunning product- Beast series. Beast series ESC are well designed and tested and fine-tuned by the experienced driver proven to be a reliable quality ESC. On top of this, we make it more resistant to water. Not splash, it’s real waterproof. You can run your vehicles through the morning dew, down the muddy road, across the soggy snow or just about anywhere else you’d be interested in running a 1/8th scale RC buggy or truck. We are using today's state of the art micro components, The ESC delivers advanced tuning options for the hardcore racer. Whether you are into large scale or short course, Beast has what racers demand; reliability, precise control and unmatched power handling capability. Also for the sake of safety, we offer you the accurate voltage and temperature protection to make sure you are using within the safe limits. Wide range of parameter configuration and friendly PC interface setting make it even more perfect choice to gear up your vehicle.

Features:
1. Enhanced throttle response, excellent acceleration, strong brakes and throttle linearity
2. Using advanced software interface to set up or update the software or using programming card to make adjustments.
3. Using PC or programming card to program forward or reverse throttle limit
4. Using PC to program braking percent
5. Multiple protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protection
6. Compatible with NOVAK, LRP, ORION Sensored brushless motor
7. MOSFET design provides high-current output (1080 amp peak) with incredibly low resistance (.0003 Ohm)
8. Micro-fin aluminum heat sink dissipates heat.
9. Industrial leading edge waterproof design

source from http://www.ztwshop.com

1:10 Beast SL 45A

source from http://www.ztwshop.com

Our team has been dedicating lots of time and efforts to bring you this completely stunning product. Beast series ESCs are finely designed and tested and fine-tuned by the experienced driver proven to be a reliable and quality ESC. On top of this, we make it more resistant to water. Not splash, it’s real water proof. You can run your vehicles through the morning dew, down the muddy road, across the soggy snow or just about anywhere else you’d be interested in running a 1/10th scale RC buggy or truck. Our Beast 45A and 60A are for the pre-professional level, no matter what vehicle you are driving, it will delivers you more what you expected. Also for the sake of safety, we offer you the accurate voltage and temperature protection to make sure you are using within the safe limits. This is the one ESC you ever dream about who will give you performance at very reasonable,affordable price, definitely a best value keeper for your vehicle.

Features:
1 Enhanced throttle response, excellent acceleration, strong brakes and throttle linearity
2 Using program card to make adjustments.
3 Using program card to program forward or reverse throttle limit
4 Using program card to program braking percent
5 Multiple protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protection
6 Compatible with NOVAK, LRP, ORION brushless motor
7. Micro-fin aluminum heat sink dissipates heat.
8.Industrial leading edge waterproof design

Specifications:
Max Continuous Current - 45A
Burst Current - 260A
BEC Output - 6V/2A
Motor Type - 4 Pole Sensorless Brushless Motor
Battery - 5-10 Cell NiMH/NiCd or 2-3s Lipo
Suitable Vehicle - 1:10 on-road and off-road cars/trucks, SCT
Operation Environment - Waterproof design allows you to use in nearly any environment
Resistance - .0010 ohm
Length - 44mm
Width - 32mm
Height - 37mm
Weight - 95g
source from http://www.ztwshop.com

Waterproof Beast SL 120A brushless ESC for 1:10 and 1:12 short course trucks.
Source from http://www.ztwshop.com
Our team has been dedicating lots of time and efforts to bring you this completely stunning product. Beast series ESCs are finely designed and tested and fine-tuned by the experienced driver proven to be a reliable and quality ESC. On top of this, we make it more resistant to water. Not splash, it’s real water proof. You can run your vehicles through the morning dew, down the muddy road, across the soggy snow or just about anywhere else you’d be interested in running a 1/10th scale RC buggy or truck,SCT. No matter what vehicle you are driving, it will delivers you more what you expected. Also for the sake of safety, we offer you the accurate voltage and temperature protection to make sure you are using within the safe limits. This is the one ESC you ever dream about who will give you performance at very reasonable,affordable price, definitely a best value keeper for your vehicle.

Features:
1 Enhanced throttle response, excellent acceleration, strong brakes and throttle linearity
2 Using program card to make adjustments.
3 Using program card to program forward or reverse throttle limit
4 Using program card to program braking percent
5 Multiple protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protection
6 Compatible with NOVAK, LRP, ORION brushless motor
7. Micro-fin aluminum heat sink dissipates heat.
8.Industrial leading edge waterproof design

Specifications:
Max Continuous Current - 120A
Burst Current - 760A
BEC Output - 6V/3A
Motor Type - 4 Pole Sensorless Brushless Motor
Battery - 5-12 cell NiMH/NiCd or 2-3s Lipo
Suitable Vehicle - 1:10 scale short course, on and off road racer
Operation Environment - Waterproof design allows you to use in nearly any environment
Resistance - .0003 ohm
Length - 52mm
Width - 38mm
Height - 36mm
Weight - 103g

Source from http://www.ztwshop.com

We all know that that boaters crave for more power than cars and airplanes and ZTW has come up with a whole new way to put the power to the water – The new SEAL line water-cooling brushless speed controls for marine applications. ZTW uses new FETS that offer less resistance and less heat dissipated. Even so they added more water-pipes to increase the cooling area to dissipate the heat faster and better so as to bring a even more incredible power levels without any risk of frying the controller.

Well designed MCU with efficient code makes for faster sync and accurate control. Beside the performance they have also bring you a whole new fashion looking marine ESC.

This is their SEAL marine speed controller. Quality, performance and fashion are what they are all about.

Features:
1. Extremely low internal resistance
2. High efficient three pipe water cooling system
3. Super smooth and accurate throttle linearity
4. Over temperature protection
5. Auto throttle shut down in signal lose situation
6. Supports high RPM motors
7. Power arming protection (prevents the motor from accidentally running when switched ON)
8. New Advanced programming software

Specifications:
Continuous Current - 300A
Burst Current (10s) - 180A
Battery - 5-18 NC/2-6 LiPo
BEC Output - 5.5V/3A
Width - 65mm
Length - 46mm
Height - 23..5mm
Weight - 780g

Source from http://www.ztwshop.com

We all know that that boaters crave for more power than cars and airplanes and ZTW has come up with a whole new way to put the power to the water – The new SEAL line water-cooling brushless speed controls for marine applications. ZTW uses new FETS that offer less resistance and less heat dissipated. Even so they added more water-pipes to increase the cooling area to dissipate the heat faster and better so as to bring a even more incredible power levels without any risk of frying the controller.

Well designed MCU with efficient code makes for faster sync and accurate control. Beside the performance they have also bring you a whole new fashion looking marine ESC.

This is their SEAL marine speed controller. Quality, performance and fashion are what they are all about.

Features:
1. Extremely low internal resistance
2. High efficient three pipe water cooling system
3. Super smooth and accurate throttle linearity
4. Over temperature protection
5. Auto throttle shut down in signal lose situation
6. Supports high RPM motors
7. Power arming protection (prevents the motor from accidentally running when switched ON)
8. New Advanced programming software

Specifications:
Continuous Current - 200A
Burst Current (10s) - 180A
Battery - 5-18 NC/2-6 LiPo
BEC Output - 5.5V/3A
Width - 65mm
Length - 46mm
Height - 23..5mm
Weight - 225g

Source from http://www.ztwshop.com

http://www.xblade-tech.com/blog/wp-c...ko-526x400.jpg

all Gecko ESCs are now shipping from Altitude Hobbies with the latest firmware files pre-installed. Follow the instructions below to update your existing ESC if you are experiencing timing issues.

Hey, everyone –

As many of you know, the ZTW Gecko ESCs began experiencing timing issues with many of the new Motrolfly motors which would cause commutation errors or a glitching during run up. Altitude Hobbies has been working hard with ZTW over the past several months to fix this issue, and we believe we have. ZTW has developed new firmware updates for both the SBEC and HV OPTO versions of the ESCs. We have tested the SBEC update with several Motrolfly motors and it seems to have fixed the issue; we’re still waiting on test reports with the OPTO firmware, but are fairly confident it will work well also.

Therefore, if you would like to receive this updates,

P.S. There’s lots of discussion threads going on about this issue, and I cant possibly cover them all. So, I’m posting this in a few places to hopefully spread the word as much as possible.

SBEC VERSION ONLY download link: http://www.ztwshop.com/support/download/

OPTO HV VERSION ONLY (NEW): http://www.ztwshop.com/support/download/

OPTO HV VERSION ONLY (Original): http://www.ztwshop.com/support/download/

NOTE: difference between NEW and ORIGINAL OPTO versions…..the original file is the “original” firmware these ESCs came with when released a couple...Continue Reading

ZTW Spider OPTO ESCs

source from: http://www.ztwshop.com/product/ztw-s...brushless-esc/
are quality speed controllers and designed for simple installation and easy setup. These ESCs have proven to offer excellent performance in Multi-rotor applications. If you are starting out in Multi-rotors and need an easy-to-install solution that is tested and proven to work with Multi-rotor craft then these speed controllers have you covered. The ZTW Spider 12A OPTO ESC features a very smooth yet linear throttle response, without sacrificing a rapid, crisp, response to any throttle input. Super fast Refresh Rate up to 600Hz make these a very smooth controller.

FEATURES:

Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal loss situations
Supports high RPM motors
Power arming protection
Use new generation of the MOSFETs
REQUIRES:

Direct connection to motor or bullet connectors
Battery connector
NOTES:

This 12A ESC has bare leads only.

PRODUCT SPECIFICATIONS:

Length
26mm / 1.02in
Width
15mm / 0.59in
Height
6mm / 0.23in
Weight
8g
MAX Output
Continuous Current 12A
Burst Output
20A
Battery
5-18NC/2-4Lipo
BEC Output
5.0V 6.0V 7.4V 8.4V Adjustable/8A
Power Connector
Bare Leads
Motor Connector
Bare Leads

Source from; http://www.ztwshop.com/product/ztw-s...brushless-esc/

This programming card is specifically designed for the ZTW Mantis Series electronic speed controls.

HOW TO USE THE LED PROGRAM CARD:

ZTW Program card with LED display is easy to use and convenient to carry. All of the programmable functions are shown on the program card.
Turn on the ESC. Remove the signal wire and plug it into the top-socket on the program card, wait for 2 seconds until the LED is on.
If ESC is not connected with the batteries, the program card should be connected with other power supply, the range of power supply is from 5.0V to 6.3V.

http://www.ztwshop.com/product/Program-Card/
Press the button ”Menu” on the program card and circularly select each programmable function. At that time the number of programmable function will be displayed on the left of the LED, the current value will be displayed on the right side. Then press the button “Value” to change the value and press the button “OK” to confirm. At the same time the Red indicating LEDs of both program card and the ESC will blink. Turn off the ESC, the modified settings will be saved in the ESC`s memory.
Press the button “Reset” to restore the default settings.
SPECIFICATIONS:

1.Size: 70.0mm*45.0mm*13.0mm (L*W*H)
2.Weight: 23.0g

Source from http://www.ztwshop.com/product/Program-Card/

ZTW Spider 12A OPTO ESC - ZTW5012301
ZTW Spider OPTO ESCs are quality speed controllers and designed for simple installation and easy setup. These ESCs have proven to offer excellent performance in Multi-rotor applications. If you are starting out in Multi-rotors and need an easy-to-install solution that is tested and proven to work with Multi-rotor craft then these speed controllers have you covered. The ZTW Spider 12A OPTO ESC features a very smooth yet linear throttle response, without sacrificing a rapid, crisp, response to any throttle input. Super fast Refresh Rate up to 600Hz make these a very smooth controller.

FEATURES:

Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal loss situations
Supports high RPM motors
Power arming protection
Use new generation of the MOSFETs
REQUIRES:

Direct connection to motor or bullet connectors
Battery connector
NOTES:

This 12A ESC has bare leads only.

PRODUCT SPECIFICATIONS:

Length
26mm / 1.02in
Width
15mm / 0.59in
Height
6mm / 0.23in
Weight
8g
MAX Output
Continuous Current 12A
Burst Output
20A
Battery
5-18NC/2-4Lipo
BEC Output
5.0V 6.0V 7.4V 8.4V Adjustable/8A
Power Connector
Bare Leads
Motor Connector
Bare Leads

Follow us
Facebook: https://www.facebook.com/pg/ZTW-Offi...3619874614439/


source from: http://www.ztwshop.com/product/ztw-spider-series-brushless-esc/

This ZTW Gecko series ESC is a high-quality,

Source from: http://www.ztwshop.com/product/ztw-g...brushless-esc/

efficient brushless electronic speed control with an integrated switch-mode BEC. It can operate without the need for a separate receiver battery to power your servos and receivers saving you weight and simplifying your electronic connections. The Gecko series includes an aluminum heat sink body which is lightweight and helps dissipate heat more efficiently. The BEC on the Gecko has been specifically designed to support higher current applications to eliminate the possibility of unwanted shutdowns, and it is also capable of supporting simultaneous multiple servo operations typically found in large-scale airplanes and CCPM equipped large-scale 3D helicopters. If you are looking for a top of the line, full-featured ESC at a competitive price, the ZTW Gecko is the logical choice.

FEATURES:

Data logging system such as temperature, voltage, current, and RPM
SBEC Voltage Output 5.0, 6.0, 7.4, and 8.4V
Advanced Governor Mode and soft start
High SBEC Current Output, continuous 8A and burst 16A, designed to meet your high current applications
Power arm protection, over-heat protection, low-voltage protection and lost-signal protection
Secondary sub-menu setting by the LCD program card or your PC
Super smooth and accurate throttle linearity
Support for most motors, including high RPM motors
Programmable motor timing
Utilizes new smaller MOSFET technology...Continue Reading

The ZTW Mantis series is designed as a performance upgrade for your stock/OEM ESC.

Source from: http://www.ztwshop.com/product/ztw-m...brushless-esc/

Its performance, feature set, and stability make it the perfect enhancement for your RC electric airplane or helicopter. It features compact size, light weight, simplified PCB design, super-smooth start up and throttle linearity, multiple circuit protections, governor, high amp BEC output and more. If you want to boost the performance of your stock ESC, the ZTW Mantis is an ideal choice offering a long list of advanced features and solid, reliable construction.

FEATURES:

Supports high RPM motors and can be used with most RC motors
Secondary sub-menu setting for easier programming
Advanced Governor Mode
More optional motor timing and soft acceleration setups
Super smooth and accurate throttle linearity
Power arming protection (prevents the motor from accidentally running when switched ON)
Auto throttle shut down in a signal loss situation
Safety thermal over-load protection
Uses the new generation of the MOSFET to ensure the ESC stays within operating temperatures and can support peak current draws
New v3.1 advanced programming software
INCLUDES:

ZTW Mantis 85A ESC with 5A SBEC
Pre-installed XT-60 Connector (power connector) and 3.5mm bullet (motor connector) for your convenience
Instruction manual
OPTIONAL:

ZTW LED Programming Card - Click Here for More Info
PRODUCT SPECIFICATIONS:

Length
47mm / 1.85in
Width
35mm / 1.37in
Height
15mm / 0.59in
Weight
57g
MAX Output
Continuous Current 85A
Burst Output
100A (10s)
Battery
2-6Lipo/5-18NC
BEC Output
5V 5.5V 6V Adjustable/5A
Power Connector
XT-60
Motor Connector
3.5mm bullets

More info: http://www.ztwshop.com/product/ztw-m...brushless-esc/

ZTW Mantis 6A ESC - ZTW2006101
Source from: http://www.ztwshop.com/product/ztw-m...brushless-esc/
The ZTW Mantis series is designed as a performance upgrade for your stock/OEM ESC. Its performance, feature set, and stability make it the perfect enhancement for your RC electric airplane or helicopter. It features compact size, light weight, simplified PCB design, super-smooth start up and throttle linearity, multiple circuit protections, governor, high amp BEC output and more. If you want to boost the performance of your stock ESC, the ZTW Mantis is an ideal choice offering a long list of advanced features and solid, reliable construction.

FEATURES:

Supports high RPM motors and can be used with most RC motors
Secondary sub-menu setting for easier programming
Advanced Governor Mode
More optional motor timing and soft acceleration setups
Super smooth and accurate throttle linearity
Power arming protection (prevents the motor from accidentally running when switched ON)
Auto throttle shut down in a signal loss situation
Safety thermal over-load protection
Uses the new generation of the MOSFET to ensure the ESC stays within operating temperatures and can support peak current draws
New v3.1 advanced programming software
INCLUDES:

ZTW Mantis 6A ESC
Pre-installed JST Connector (power connector) and 2mm bullet (motor connector) for your convenience
Instruction manual
OPTIONAL:

ZTW LED Programming Card - Click Here for More Info
PRODUCT SPECIFICATIONS:

Length
21mm / 0.8in
Width
14mm / 0.55in
Height
7mm / 0.27in
Weight
6g
MAX Output
Continuous Current 6A
Burst Output
8A (10s)
Battery
2-3Lipo/5-10NC
BEC Output
5V/1A
Power Connector
JST Connector
Motor Connector
2mm bullets

source from: http://www.ztwshop.com/product/ztw-m...brushless-esc/

ZTW Mantis 25A ESC - ZTW2025101

Source from: http://www.ztwshop.com/product/ztw-m...brushless-esc/

The ZTW Mantis series is designed as a performance upgrade for your stock/OEM ESC. Its performance, feature set, and stability make it the perfect enhancement for your RC electric airplane or helicopter. It features compact size, light weight, simplified PCB design, super-smooth start up and throttle linearity, multiple circuit protections, governor, high amp BEC output and more. If you want to boost the performance of your stock ESC, the ZTW Mantis is an ideal choice offering a long list of advanced features and solid, reliable construction.

FEATURES:

Supports high RPM motors and can be used with most RC motors
Secondary sub-menu setting for easier programming
Advanced Governor Mode
More optional motor timing and soft acceleration setups
Super smooth and accurate throttle linearity
Power arming protection (prevents the motor from accidentally running when switched ON)
Auto throttle shut down in a signal loss situation
Safety thermal over-load protection
Uses the new generation of the MOSFET to ensure the ESC stays within operating temperatures and can support peak current draws
New v3.1 advanced programming software
INCLUDES:

ZTW Mantis 25A ESC
Pre-installed XT60 Connector (power connector) and 2.0mm bullet (motor connector) for your convenience
Instruction manual
OPTIONAL:

ZTW LED Programming Card - Click Here for More Info
PRODUCT SPECIFICATIONS:

Length
28mm / 1.10in
Width
26mm / 1.02in
Height
9mm / 0.35in
Weight
19g
MAX Output
Continuous Current 25A
Burst Output
35A (10s)
Battery
2-4Lipo/5-12NC
BEC Output
5V/2A
Power Connector
XT60 Connector
Motor Connector
2.0 mm bullets

Source from: http://www.ztwshop.com/product/ztw-m...brushless-esc/

ZTW Gecko 150A ESC OPTO High Voltage (HV) - ZTW4150401

Source from http://www.ztwshop.com/product/ztw-g...brushless-esc/

This ZTW Gecko series ESC is a high-quality, efficient brushless electronic speed control. It can operate without the need for a separate receiver battery to power your servos and receivers saving you weight and simplifying your electronic connections (but a separate BEC is required, see below). The Gecko series includes an aluminum heat sink body which is lightweight and helps dissipate heat more efficiently. If you are looking for a top of the line, full-featured ESC at a competitive price, the ZTW Gecko is the logical choice.

FEATURES:

Data logging system such as temperature, voltage, current, and RPM
Advanced Governor Mode and soft start
Power arm protection, over-heat protection, low-voltage protection and lost-signal protection
Secondary sub-menu setting by the LCD program card or your PC
Super smooth and accurate throttle linearity
Support for most motors, including high RPM motors
Programmable motor timing
Utilizes new smaller MOSFET technology to minimize weight
Aluminum finned heat sink
Programmable throttle input range
Anti-spark circuitry (on HV OPTO models only）
ESC firmware and program settings can be updated via PC connection (USB adapter sold separately)
INCLUDES:

ZTW Gecko 150A ESC OPTO
Pre-installed EC5 Connector (power connector) and 5.5mm bullet (motor connector) for your convenience
Instruction Manual
REQUIRES:

ZTW 10A BEC/UBEC - ZTW300200010
OPTIONAL:

ZTW LCD Programming Card - More Info
WiFi Programming Module - More Info
PRODUCT SPECIFICATIONS:

Length
65mm / 2.55in
Width
46mm / 1.81in
Height
33mm / 1.29in
Weight
123g
MAX Output
Continuous Current 150A
Burst Output
180A (10s)
Battery
18-38NC/6-12Lipo
BEC Output
N/A
Power Connector
EC5 Connector
Motor Connector
5.5mm bullets

More info: http://www.ztwshop.com/product/ztw-g...brushless-esc/

ZTW Gecko 120A ESC OPTO High Voltage (HV) - ZTW4120401
Source from http://www.ztwshop.com/product/ztw-gecko-series-brushless-esc/
This ZTW Gecko series ESC is a high-quality, efficient brushless electronic speed control. It can operate without the need for a separate receiver battery to power your servos and receivers saving you weight and simplifying your electronic connections (but a separate BEC is required, see below). The Gecko series includes an aluminum heat sink body which is lightweight and helps dissipate heat more efficiently. If you are looking for a top of the line, full-featured ESC at a competitive price, the ZTW Gecko is the logical choice.

FEATURES:

Data logging system such as temperature, voltage, current, and RPM
Advanced Governor Mode and soft start
Power arm protection, over-heat protection, low-voltage protection and lost-signal protection
Secondary sub-menu setting by the LCD program card or your PC
Super smooth and accurate throttle linearity
Support for most motors, including high RPM motors
Programmable motor timing
Utilizes new smaller MOSFET technology to minimize weight
Aluminum finned heat sink
Programmable throttle input range
Anti-spark circuitry (on HV OPTO models only）
ESC firmware and program settings can be updated via PC connection (USB adapter sold separately)
INCLUDES:

ZTW Gecko 120A ESC OPTO
Pre-installed EC5 Connector (power connector) and 5.5mm bullet (motor connector) for your convenience
Instruction Manual
REQUIRES:

ZTW 10A BEC/UBEC - ZTW300200010
OPTIONAL:

ZTW LCD Programming Card -
WiFi Programming Module -
PRODUCT SPECIFICATIONS:

Length
65mm / 2.55in
Width
46mm / 1.81in
Height
17mm / 0.66in
Weight
115g
MAX Output
Continuous Current 120A
Burst Output
150A (10s)
Battery
5-18NC/6-12Lipo
BEC Output
N/A
Power Connector
EC5 Connector
Motor Connector
5.5mm bullets

ZTW Car ESC user manual Free download

http://www.ztwshop.com/support/download/

http://www.ztwshop.com/support/download/

http://www.ztwshop.com/support/download/

Beast SL 60A Waterproof 1:10 & 1:12 Scale brushless ESC for short course trucks.

Our team has been dedicating lots of time and efforts to bring you this completely stunning product. Beast series ESCs are finely designed and tested and fine-tuned by the experienced driver proven to be a reliable and quality ESC. On top of this, we make it more resistant to water. Not splash, it’s real water proof. You can run your vehicles through the morning dew, down the muddy road, across the soggy snow or just about anywhere else you’d be interested in running a 1/10th scale RC buggy or truck. Our Beast 45A and 60A are for the pre-professional level, no matter what vehicle you are driving, it will delivers you more what you expected. Also for the sake of safety, we offer you the accurate voltage and temperature protection to make sure you are using within the safe limits. This is the one ESC you ever dream about who will give you performance at very reasonable,affordable price, definitely a best value keeper for your vehicle.

Features:
1 Enhanced throttle response, excellent acceleration, strong brakes and throttle linearity
2 Using program card to make adjustments.
3 Using program card to program forward or reverse throttle limit
4 Using program card to program braking percent
5 Multiple protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protection
6 Compatible with NOVAK, LRP, ORION brushless motor
7. Micro-fin aluminum heat sink dissipates heat.
8.Industrial leading edge waterproof design



Specifications:
Max Continuous Current - 60A
Burst Current - 380A
BEC Output - 6V/2A
Motor Type - 4 Pole Sensorless Brushless Motor
Battery - 5-10 Cell NiMH/NiCd or 2-3s Lipo
Suitable Vehicle - 1:10 on-road and off-road cars/trucks, SCT
Operation Environment - Waterproof design allows you to use in nearly any environment
Resistance - .0007 ohm
Length - 44mm
Width - 32mm
Height - 37mm
Weight - 95g