Posted by Jim.Thompson | Today @ 06:17 AM | 309 Views
A buddy and mine picked this up at the local scrap metal heap at the tip.
After dismantling and inspection, I decided it was in surprisingly good order inside, despite the rough exterior condition.
I have cut it down in the usual way, increased the compression ratio and adjust the port timing to suit.
I made a spark plug adapter to fit a CM-6 plug, as the 14 mm plug that it came with stuck out to far near the plug when the lead was fitted.
Running on AvGas and Stihl Ultra oil @ 30:1.

First run today, after some starting problems. Some tuning and fiddling required, but it goes ok.
17 x 6 propeller.

Short video here:

21cckioritz (0 min 20 sec)

Posted by CaseySP | Today @ 05:22 AM | 401 Views
Latest version of the Alfa Corsair retracts. I haven't flown this for some time with the wing modified for flaps/retracts as the earlier version of the retract actuation became more and more unreliable.

Thanks to a bit of spare time lately with our airfield closed due to COVID-19, have pulled the wing down from the shelf for some more tinkering.

This looks quite promising - very robust and reliable. Was able to replace the HS-81MG servo (17g) with a lighter Turnigy TSS-10MG (10g) - so maybe a neutral impact on weight allowing for the bell-cranks but removing the flexible Gold 'n Rods.

Alfa Corsair Retracts (0 min 38 sec)

Posted by jmxp69 | Today @ 02:15 AM | 856 Views
I put the Sunnysky x2820 (3542) 800kv motor to the test on The Judge. This is one efficient motor.
Efficiency Champ? Sunnysky x2820 800kv First Look and Bench Test [The Judge Ep. 6] (27 min 29 sec)

Posted by dgliderguy | Today @ 01:29 AM | 950 Views
So I had this nice pair of Flyzone Beaver floats, with no plane to put them on, and got all inspired to pull down my dusty old 53" Easy Built Pilatus Porter kit from the stack. The kit is cheap, but builds up into a rather nice model, really. It is meant for electric power, but I thought it would be more fun to have at least one glow engine powered floatplane in my fleet of water birds, so I tossed the cheap vac-formed cowl in the trash and made a proper flat-plate mount for my OS10FP. I have a half-dozen of these engines, and they all run great. Not a lot of power, but reliable. I like that.

Today, however, I decided to maiden the Pilatus off the grass runway, with the optional wire landing gear I made for it. No sense letting a perfectly good model sit on the shelf and wait for the float-fly to come along. The little OS10FP was a bit reluctant to pull the Pilatus off the dripping wet sod, but once clear of the ground it climbed out nicely. I wonder if it will have enough power for water flying with the floats. If it needs a bigger engine, I have a Magnum .15 that will drop right in the same mount, with some minor hole relocations. Anyway, the OS10FP is a good match for this 32oz model, and I flew around for most of the flight at partial throttle. Loops were effortless, the stall was tame as a lazy house cat, and the landings were floaty and easy. I will need to move the mains forward another inch, though, as I couldn't keep the Pilatus from tipping on its nose in the last foot or so of the rollout. (I should have seen that coming. My usual rule is wheels no further back than the leading edge of the wing.)

What fun! A hybrid sport scale floatplane/landplane, for some relaxing S.M.A.L.L flying out at the field. Now I can't wait to hit the lake this summer!
Posted by Bursuc1980 | Today @ 01:07 AM | 1,002 Views
Anybody can explain to me if i can convert this PSU in to a programming power supply?
Read different threaded but i can find nothing about this
Posted by SeaEraCaptain | Yesterday @ 11:30 PM | 1,239 Views
During my time hunkering down due to the Coronavirus pandemic I have returned a Carl Goldberg Super Chipmunk to flying condition.

I picked up the airplane at the Westminster Maryland RC Swap Meet in 2017 or 2018, until recently I haven't had time to get it ready.

This airplane has been built immaculately, it is covered in monokote in the traditional Art Scholl scheme.

The airplane is fitted with an OS 91 Surpass II 4 Stroke Engine; stock muffler; Zinger 14 x 6 propeller; Futaba servos; Futaba S3008SB receiver and Futaba 10J transmitter.

During set up of the airplane I discovered the prior owner left behind a nice microswitch activated glow driver. I just had to trim the throttle servo arm slightly to ensure that it only comes on at or below 1/4 throttle. It is activated by an on off switch on the outside of the fuselage. When the airplane is not in use I make sure to leave the throttle servo at 1/3 throttle or higher to avoid engaging the microswitch in case the external on - off switch should get bumped. The sub C cell that lights up the glow plug was still OK, I was able to charge it and it does hold a charge.

I did make some modifications to the throttle linkage, it is the type that goes out past the carb throttle linkage and then hooks back to it. As it was it went out a little too far allowing the piano wire to flex some so it did not open the throttle correctly. I cut some of the wire off and shortened up the linkage back at the servo arm to account for
...Continue Reading
Posted by skeeter honey | Yesterday @ 08:23 PM | 1,459 Views
About six months ago I bought my first kit: the GWS AT-6 (EPS version). They're still relatively abundant and inexpensive, so why not?

I've chipped away at it for all this time, often waiting for parts, usually waiting for corrections to my mistakes to dry/set/whatever. Throughout all of this I've messed around with other planes in order to figure out many of the skills I'll need to actually fly this thing. Now that I have all the pieces, to include Tx/Rx/battery/motor/ESC/etc., I've turned a corner inits completion and am nearing the maiden, which should be this month.

Why I insisted on flaps and retracts on my first build...well, it's probably because good planes with them are so relatively expensive and I wanted those features too bad to fly this thing without them. This has cost me time and money, and has led to several mistakes that have caused significant delays. Namely, using the wrong epoxy at one point, despite reading the threads on this plane that warned against it. I thought I was careful, but I wasn't. This led me to learn about Foam-Tac, which is a great product, but not as easy to use as others make it seem.

Other challenges come from my fear of the wings splitting apart, brown outs, bad soldering, or just bad flying. Alleviating these fears cause more delays.

Then the retracts themselves. I just couldn't get a set small enough to not protrude beyond the wing surface, so my solution is inelegantly permanent. A failure will be a problem to say the least.

So after no further ado, here are a few pics of the progress so far . I'm yet to paint the beige parts or any part of the wing, but I have primed everything and installed all the servos, most control fittings, and protective shields for underwing components.
Posted by Blaze0021 | Yesterday @ 07:01 PM | 1,508 Views
(Profanity Alert) Mike sees my Eflite Rare Bear on 4S with the APC 9x9E for the first time with this prop upgrade. I think he likes it. 😆

Eflite Rare Bear 880mm BNF Basic w/AS3X - 4S Flight w/APC 9x9E Prop Preview (Profanity Alert) (0 min 46 sec)

Full video to come soon!
Posted by SeaEraCaptain | Yesterday @ 05:00 PM | 1,603 Views
During my time hunkering down due to the Coronavirus pandemic I have returned a vintage Joe Bridi Dirty Birdy 60 pattern airplane to flying condition.

I picked up the airplane at the Lebanon PA RC Swap Meet in early March - that was one of the last normal things I was able to do before the onset of the pandemic.

This is a kit built verion of the airplane - it has been very nicely painted by it's prior owner.

The airplane is fitted with an OS 61 SF Engine; stock muffler; Master Airscrew 12 x 8 propeller; Tru Turn spinner; JR Servos; Futaba S3008SB receiver and Futaba 10J transmitter.

The prior owner said he did fly the airplane with an OS 61 size engine - that is true because the 61 SF dropped right into the airplane and the Tru Turn spinner with it's flush backplate fit right up to the nose with about 1mm or less clearance. That is as close as I would ever want the spinner to be to the airframe.

The prior owner did add some weight to the rear of the fuselage - after fitting my gear to the airplane I did find that it was a little on the nose heavy side but not unacceptably so. The battery pack is mounted behind the servos in the fuselage as far back as I could get it without having to do surgery (it sits in the main fuselage area toward where the wing bolts are - its securely mounted out of the way to the top side of the inner fuselage).

I fly off a grass field so I ditched the small wheels that were on the airplane in favor of 2.75" wheels. There's a
...Continue Reading
Posted by Tazkiller85 | Yesterday @ 05:07 AM | 2,854 Views
Yep Les Amis,
Des NEWS et du FUN ! Pas mal de choses différentes dans cette vidéo, j'avais envie de vous détendre un peu tout en vous apportant quelques infos importantes. Je vous laisse découvrir ...
Bon Film à Tous ... Merci de votre soutien ... Et tenez bon !

Tinywhoop et Miniquad comparatif / Nouveautés et Mises à jour ... (24 min 33 sec)


Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous :

- Mise à Jour chargeur D6 Duo Pro : https://bit.ly/2R8BuhG
- EMAX Tinyhawk II RACE : http://bit.ly/2IP7O4J
- Eachine TYRO 89 : http://bit.ly/35HGhuM
- Eachine Tyro69 105mm ( Coupon BG4ty69 ) : http://bit.ly/2kkQJa9
- BETA 65X : https://bit.ly/2xGRSPm
- EMAX TinyHawk II (Coupon BGFLYING10 pack RTF ) : http://bit.ly/38TSCij
- HX115 HD Beta FPV : http://bit.ly/2NHq1mC
- HGLRC VEYRON 3 6S : https://bit.ly/397jRFc
- FIMI X8 SE 2020 Entrepôt SE ( Coupon BGFIMIX8SE20 ) : https://bit.ly/342gCOp
- Sangles RJXHobby : https://bit.ly/3e2IzKy
- Lampe led Flash : https://bit.ly/2UEl1ny

- TABLEAU DES PROMOS ET COUPONS BANGGOOD 2020 (remis à jour régulièrement, pour aider la chaîne, gardez ce lien en favori ou raccourci pour vos achats sur Banggood ) : http://bit.ly/2OiQMPF

- Si Vous voulez aider la chaîne avec un don (tous les dons servent à alimenter les vidéos en produits ou matériel ): https://streamlabs.com/Tazkiller85

BIENTÔT EN TEST :
- X-Flip Modular : http://bit.ly/2OWezVw
-...Continue Reading
Posted by Tazkiller85 | Yesterday @ 04:33 AM | 2,908 Views
Yep Les Amis,
Mon BETA préféré pour l'instant ! Ok, je n'ai pas choisi le bon jour pour tester ce nouveau Tiny de chez BETAFPV ... 60km/h de vent c'est environs 40km/h de trop pour ce petit BETA65X ! Bien sur, je ferai d'autres images (avec plaisir ! lol ) par temps calme, pour que vous vous rendiez compte de ses possibilités. En attendant, croyez moi sur parole, il est très performant en extérieur et surtout, très résistant. Le châssis ultra léger et souple ne casse pas facilement et la canopée moulée est presque incassable rapport au poids de l'engin ! Les réglages d'origines sont bons et la mise en route très rapide . En bref, une très bonne surprise et un excellent petit engin en ces jours de confinement . Bon Film à Tous et Merci de votre soutien .

BetaFPV Beta65X V2 - Review Test Démo - Un excellent Tinywhoop ! (20 min 32 sec)


NOTATAZ : 18/20 Pas déçu du tout ! ...

Niveau : Débutants et Confirmés
Les + : Puissant, maniable et doux en indoor, Bons réglages d'origine, Résistant, Bonne caméra, Autonomie, Portée radio, VTX 25mw efficace !
Les - : A voir avec le temps ...

Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous :

- BETA 65X : https://bit.ly/2xGRSPm
- Châssis 65X : https://bit.ly/33YuFED
- Moteurs 0802 14 000KV : https://bit.ly/2wSfqAV
_ Carte AIO F4 : https://bit.ly/2wVZiOG
- Caméra C01 pro : https://bit.ly/39tMe0k
- Canopée moulée : https://bit.ly/3azpLAp
- Hé...Continue Reading
Posted by Jupes | Yesterday @ 01:24 AM | 4,829 Views
Getting back into the hobby after a long hiatus. Shown are a few of my favorite planes
Posted by old4570 | Apr 03, 2020 @ 09:04 PM | 6,727 Views


I spied with my eye ! > https://www.banggood.com/custlink/GmGKkjSvdN
But way to kill interest with the insane shipping cost though ..
Yeah , $136.35 for shipping .. ( Thats on the nose )

Looks interesting , BUTT !
Posted by AquilaGlider | Apr 03, 2020 @ 06:17 PM | 7,144 Views
Killin' back in the 70's but got tied up w my career. Now have time to get back to where it all started. Boy have things changed. Balsa, Ambroid, Monokote? Check out my info in 'About AquilaGlider'.
Posted by German Barrios | Apr 03, 2020 @ 06:16 PM | 7,127 Views
Just got this RC Surfer 4 edition from Kyosho...I will review him at my local beach after StayHome order passed.
Posted by jmxp69 | Apr 03, 2020 @ 05:41 PM | 7,230 Views
I had an opportunity to capture footage of a friend's 2M F3A Pattern Plane.
2 METER Extreme Flight Vanquish F3A RC Plane Pattern Ship Flight (25 min 51 sec)

Posted by Old_Pilot | Apr 03, 2020 @ 04:57 PM | 7,396 Views
There's an airplane in here.....I promise
Posted by jhax01 | Apr 03, 2020 @ 04:00 PM | 7,355 Views
Timber UMX - 64
Turbo Timber - 130
RocHobby MXS - 56
Hookll Extra 300 - 23
E-Flite Extra 300 1.3m - 12
Future Model Edge 38" - 71
Extreme Flight Edge 48" - 36
Extreme Flight Edge 52" - 22

RF9 (6 minute timer) - 325

Current favorite - EF Edge 52" Bonded with it immediately, it just flies soooo well...
Posted by TMacFPV | Apr 03, 2020 @ 03:57 PM | 7,374 Views
Do FPV simulators really help? What's the best way to get started in FPV? 🤔

In this video I'll give you my answers to both these questions

I go over . . .
- the benefits of using a Sim to hone your flight skills
- take a quick look at the "Top 3" Sims
- use one of them to build a basic custom track (in 40 sec's!)
- and demo 4 practice drills you can use to get started with FPV flight! 🤩👍
FPV Simulator Use & Practice Drills (LEARN TO FLY!) (16 min 43 sec)