RADIOLINKRC's blog View Details
Posted by RADIOLINKRC | Sep 04, 2019 @ 01:39 AM | 732 Views
Dear Valued RadioLink Customers,
RadioLink Electronics Limited. (hereinafter referred to as RadioLink), as a well recognized brand and is dedicated to offering better RC products to more RC fans, values each of our partners and is proud of the relationships we have developed.
Unfortunately, not every distributor advertising RadioLink products has been authorized by RadioLink .Recently, it has come to RadioLink’s attention that there are three unauthorized sellers on Amazon ZIYUMR, PMac Supplies and RC & COFFEE selling RadioLink products, which cannot guaranteed authentic. RadioLink will not provide any warranty or after-sales service to such products.

RadioLink is investigating these cases and continually works to eliminate sales of RadioLink products through unauthorized distributors and their partners who engage in illegal practices from the marketplace. We trace all the serial numbers and track the product back to their source and reserve our right to cut the distributors out of our authorized system, and pursue further legal actions against unauthorized distributors who engage in illegal practices from the marketplace.In order to maintain the market order and safeguard customers’ legal rights and interests, RadioLink kindly reminds customers to purchase RadioLink’s products through RadioLink’s authorized distributors or official store RADIOLINK DIRECT.
If you have further questions please contact RadioLink Customer Service at [email protected] or [email protected] .
Thank you for your continued support to RadioLink products.
Posted by RADIOLINKRC | Sep 02, 2019 @ 05:39 AM | 896 Views
Check if the antennas of transmitter and receiver are damaged, especially the ones on receiver. The silver part at the front of the antenna is the most important as it’s the feeder line.
If the feeder line is damaged, keep flying will cause the unstable internal current which weaken the signal.

Check the RSSI value.
① Power on the transmitter and receiver with both antennas parallel and straight and within the distance of 30cm. (as picture attached below)
② Then check the RSSI value. Range between 0~-30dBM is normal and if the value gets closer to 0, the signal is stronger. If the value is between -30~-90, signal is not good and the control distance would be limited.

Check the flight environment of the antennas are all right and RSSI value is normal within the range
① Check if there is electricity substation or high voltage cable or wifi nearby.
② Check if the antenna of tansmitter and receiver is damaged or welded joint
③ Installation: try not get the receiver close to ESC/galvanometer/ metal part of the flight
④ Let the end of the receiver antenna drooped and out to avoid the signal being blocked by the flight frame.
Posted by RADIOLINKRC | Aug 19, 2019 @ 09:52 PM | 710 Views
Our latest launched T8S is READY TO ROCK !

With the super light weight of 142g , T8S has the brilliant communication performance as excellent as AT9S and AT10II and is perfectly handy for all kinds of models including Fixed Wing, Gliders, Multicopter, Cars and Boats.
  1. 2000m of Control Distance in air(with Radiolink R8EF receiver)
  2. Parameters Setup with Android APP
  3. SBUS/PPM/PWM Signal Output Supported
  4. Adapts to Multiple Models(Plane/Racing drone/Rc car/Rc boat )
  5. Programmable Mix Control
  6. Ergonomical Design with Small Dimension (162.5*95.5*57mm)
Follow our AliExpress Official, screenshot and contact the seller, you will get a $2 coupon for T8S !
https://www.aliexpress.com/item/33052706044.html…

More details please visit http://www.radiolink.com.cn/doce/pro...etail-150.html

Posted by RADIOLINKRC | Aug 13, 2019 @ 05:38 AM | 957 Views
After downloading the parameter setup APP in the android phone and powering on T8FB, an OTG cable which is packed with the T8FB, is needed .

Make sure the SMALLER end of the OTG cable is connected with the phone while the BIGGER end with the android USB cable.

(See picture here attached)

Note OTG function in Android phone should be activated first: Settings - Other settings - OTG Connection

More details about setup steps, please refer to the T8FB instruction manual downloaded from http://radiolink.com.cn/doce/UploadF...T8FBManual.pdf
Posted by RADIOLINKRC | Aug 05, 2019 @ 05:49 AM | 1,789 Views
If you have the RadioLInk old products (RC3S/RC4G/RC4GS produced before 2018/RC6GS two-way switch version/T4EU/T4EU-6/T6EHP-E/T6EHP-S/T7F/T8FB without USB port, you are very welcome to join this #OLDTONEW.
That is, you can get a new replacement in a SUPER LOW price WITHOUT shipping the old ones back to us.
Yessss!! Just keep the old RadioLink product and have a brand new one!!!

All you need is to follow the below steps:
1/ Follow our RadioLink Facebook homepage https://www.facebook.com/Radiolink-1455452961436694/
& AliExpress Official 👉https://www.aliexpress.com/store/4714037
2/ Send a mail to [email protected] , including all necessary infos

Please click below links to have more details

T8FB http://radiolink.com.cn/doce/oldtonewt8fb.html
RC4GS/RC6GS http://radiolink.com.cn/doce/oldtonewrc4gs.html

Once we get your mail and all infos are verified, we will send you a link to place order.

Period: Till August 31

Feel free to send mails to [email protected] if you have any questions.
Posted by RADIOLINKRC | Jul 25, 2019 @ 01:08 AM | 2,686 Views
1.Plug in the proper battery first
2.Press “END” on the left and “Push” on the right and power on simultaneously (00:00:29)
3.Enter the stick Calibration menu

4.Calibrate each channel one by one
5.CH1
CH1UP
* Press “End” to empty the data value
* Push Rudder stick to the LEFT and the value will change to minimum
* Press “MODE” to confirm and there will be [OK] shown on the screen
CH1CT
* Press “End” to empty the data value
* Toggle the Rudder stick at the center point
* Press “MODE” to confirm and there will be [OK] shown on the screen
CH1DN
* Press “End” to empty the data value
* Push Rudder stick to RIGHT
* Press “MODE” to confirm and there will be [OK] shown on the screen
6.CH2:
CH2UP
* Press “End” to empty the data
* Push Rudder stick to UPWARD
* Press “MODE” to confirm and there will be [OK] shown on the screen
CH2CT
* Press “End” to empty the data
* Toggle the Rudder stick
* Press “MODE” to confirm and there will be [OK] shown on the screen
CH2DN
* Press “End” to empty the data
* Push Rudder stick to DOWNWARD
* Press “MODE” to confirm and there will be [OK] shown on the screen
7.CH3:
CH3UP
* Press “End” to empty the data
* Push Throttle stick to UPWARD
* Press “MODE” to confirm and there will be [OK] shown on the screen
CH3CT
* Press “End” to empty the data
* Move the Throttle stick to center point
* Press “MODE” to confirm and there will be [OK] shown on the screen
CH3DN
* Press “End” to empty the...Continue Reading
Posted by RADIOLINKRC | Jul 19, 2019 @ 05:33 AM | 2,010 Views
As we all know that RadioLink product family is getting larger, sometimes we may get confused about the compatibility of different radios and receivers.

Here is a short list and hope it makes more clear.
  • R7FG -- RC4GS(After 20180101),RC6GS(3-position switch),T8FB
  • R12DS -- AT9,AT9S,AT10,AT10II
  • R12DSM -- AT9,AT9S,AT10,AT10II
  • R9DS -- AT9,AT9S,AT10,AT10II
  • R6DS -- AT9,AT9S,AT10,AT10II
  • R6DSM -- AT9,AT9S,AT10,AT10II
  • R8EF -- T8FB,RC4GS,RC6GS
  • R8FM -- T8FB,RC4GS,RC6GS
  • R6F -- RC4G,RC3S,RC4GS,T8FB,RC6GS
  • R6FG -- RC4G,RC3S,RC4GS,T8FB,RC6GS

Please be kindly noted that RadioLink receivers are not compatible with transmitters of other brands. Vice versa.
Posted by RADIOLINKRC | Jul 11, 2019 @ 02:35 AM | 1,898 Views
Basing on the APM open source, RadioLink flight controller Mini Pix is developed with software algorithm of damping vibration and the hardware redesigned to achieve “Alt-hold at super low height” and “Stable flight at super high speed” so that Mini Pix is applicable to various of models including heli/fixed wing/multirotors/cars/boats and different fields such as transportation, agriculture, etc. As more and more overseas users have positive feedback about Mini Pix, the APM team approached us and we have provided them our hardware circuit and files in June, 2017. The APM team has developed the open source firmware basing on RadioLink Mini Pix hardware for the Mini Pix users.

Links about RadioLink Engineer RadiolinkW submitting Mini Pix files
https://github.com/ArduPilot/ardupil...s_QMC5883L.cpp
https://github.com/ArduPilot/ardupil...aro_LPS2XH.cpp


To flash firmware

If the RadioLink Mini Pix is used for development, it is advised to flash the APM open source firmware version 3.6.0 or above. If used for RC fun/building models, choose RadioLink firmware version downloaded in RadioLink Mission Planner. Comparing with the open source firmware, firmware developed by RadioLink has better stability with the software filter algorithm added.


A. Flash Open Source Firmware
Click to flash the firmware in the open source Mission Planner downloaded via:
http://firmware.ardupilot.org/Tools/...ner-latest.msi
B.Flash RadioLink Firmware
Click to flash the firmware in the Mission Planner specially developed by RadioLink downloaded via:
http://www.radiolink.com.cn/firmware...ner-latest.exe


All interface protocals of RadioLink Mini Pix are the same as the open source pix. Therefore, the parameter setup and usage are same as the open source pix.


1.Instruction Manual of RadioLInk Mini Pix
http://radiolink.com.cn/doce/UploadF...2261419097.pdf

2.Documents of Open source Pix:
http://ardupilot.org/copter/index.html