Posted by gooniac33 | Today @ 04:35 PM | 114 Views
Big thanks to JohnVHRC for putting these videos together! The Gooniac Firey Booties look really good in this jet!!

Freewing MiG-29 Fulcrum Digital Camo Twin 80mm EDF Jet UNBOXING BUILD AFTERBURNERS FROM GOONIAC33 (17 min 49 sec)

Freewing MiG-29 Fulcrum Digital Camo Twin 80mm EDF Jet MAIDEN FLIGHT! (7 min 31 sec)
...Continue Reading
Posted by UpNup | Today @ 02:56 PM | 157 Views
Its fun to design new planes. Awhile ago, a PS4 video game caught my imagination and I mashed a Sukhoi 35/37 Super Flanker into a Macross YF-30 Chronos.


A friend recently discovered a FA-18 Hornet in an antique mall. The prop jet is made by Direct Connection I may not get it, but it reignited a desire to fire out how to bring a video game jet into the RC world.

Could the ruddervators lay down flat after takeoff when the landing gear is retracted? Could they raise back into position when the landing gear comes back down?

Weight is an issue. The Sailplane crowd uses two small Servos north of the CG to run push/pull cables. That would allow a second set of strong service to tuck into the rear a bit.

Its fun to imagine.
Posted by Cox PT-19 | Today @ 02:47 PM | 155 Views
So, there I was, MINDING my own business, when one of those vagabond visions of days long-gone slides through my tired brain.

In the mid-1970's, a couple years before getting my first reliable radio control system, we were still cranking out a fair number of control line model airplanes. Sunday flydays weren't what they'd been just a few years earlier, with girls and motorcycles having taken the lead interest, but we still managed to get some flying done.

Midwest Model Co. had released several profile control line model kits featuring (as I remember): a P-51 Mustang, P-63 Kingcobra, BF-109, and my AD-1 Skyraider. All were scaled to about the same physical size, with the intent of clubs and individual flyers staging aerial combat matches.

I sorta wanted the Kingcobra, but the Skyraider was sitting on a shelf in the hobby store, so that was it. My budget was WAY too tight to risk a plane like this to combat flying, though I think I may have flown it in the same circle with Kevin's Midwest P-51 a few times.

I built it on an overturned dresser drawer in my tiny apartment on North Park Street in Cape. So if you happen to purchase some antique furniture, and find glue blobs, pencil marks, and X-ACTO scrapings on the underside of a drawer, CONGRATULATIONS!'ve also purchased an antique control line building board!

The Skyraider was a large model for my well-worn .35, but still flew OK, with scale-like loops and horizontal 8's, AND, with the lower speed allowing me...Continue Reading
Posted by perttime | Today @ 11:08 AM | 218 Views
The calm afternoon/evening arrived today.

So, with transmitter and plastic bag in a laptop bag, the ugly Spitfire in my hand, and a battery pack in my pocket, I walked to the larger nearby clearing. Some people were out with dogs, so I waited until they got a little further away.

Before I had time to get too tense, I switched on the transmitter, connected the battery and closed the hatch. Control surfaces still moving the right way? Check. Neckstrap on, model in the left hand (I throw better with my left), push the thottle stick a bit awkwardly, brace for the impact.

And it was flying! For the first few seconds I was over-controlling, even with a plenty of expo dialled. Then, it was flying surprisingly steady. I didn't feel compelled to climb to "high" altitudes, so flew circles and figure eights, and such, not too far from me. Power wasn't all that great. It might be the old battery sagging. Still, I managed a strange shaped loop and a half cuban.

I thought I'd need to land it some time, so slowed down. I slowed down too much and it wanted to drop a wing. The first landing was not pretty. No damage, though, so I launched again and flew some circles. The second landing was better but there was a hint of wing drop before I got it down. I need to keep up more speed next time.

The GWS Spitfire is still in one piece.

I told it is ugly (for a Spitfire).



Posted by Joe01 | Today @ 09:47 AM | 230 Views
Ow do fmn olks.
Had a Volantex ASW 28 delivered the other day..WOO-HOO!! But it came without the 4 screws to hold the tail assembly together. BOO!! Does anyone out there own one and could you give me the screw length and thread size? I just thought it would be quicker to get the size and get my own!! Heres hoping folks....
Posted by Mandy Chen | Today @ 06:22 AM | 361 Views
BrotherHobby GOM 2207.5 motor, Joint designed motor!

Email: [email protected]
Posted by Tomcat Dynam | Today @ 02:25 AM | 476 Views
Detrum Blitz DT9 Upgrade V1.08

Date: 24 Sep 2020

Upgrade details:

1,Corrected the synchronization of sub-trim display unit with the whole menu.
2.Corrected the synchronization of neutral position adjustment display unit with the whole menu.
3,Corrected the sub-trim logic.

Steps as attachment.

DT9 Firmware V1.08 as attachment, you can also download here:

DT9 infomation:
Posted by lawrence4 | Today @ 01:23 AM | 605 Views
Catch PYTH700 at Maiden Flight (0 min 43 sec)

PYTH 700
Wing Material 3mm EPS
Elevon 3mm Balsa covered with clear packages tapes
C.G 138mm
Wingspan 707mm
Length 428mm
Height 120mm
Weight 220g
Motor EMAX 1804 2480kV
BEC Matek micro 5V 1.5A
Receiver DSM2 6ch
Servo EMAX ES08AII 8.5g x 2
Propeller 5030
Battery dualsky 3S 550mAh

Plan Download from: Reading
Posted by Jack Crossfire | Yesterday @ 11:39 PM | 603 Views
This would be a really shmick set of carbon fiber farsteners if it was on Lions never were impressed by 3D printed prototypes from startups, but carefully designed & manufactured parts can look really professional. The mane test is still if it stays together in the field.
Posted by MtnSnowFlyer | Yesterday @ 10:39 PM | 621 Views
I bought some "ProGo" 280 Size Quad frame parts from RCTESTFLIGHT a couple of years ago and have found them really great for experimenting. The frame has evolved into this 7 inch frame with TBS 7 inch arms and an adjustable camera mount from ShenDrones. Currently, I'm trying to get the autonomous features to work with iNav. The aluminum "bridge" is an attempt to get the GPS/compass above EM interference (with maybe some shielding?).
Posted by rclad | Yesterday @ 10:35 PM | 639 Views
I've been flying electric IMAC planes since 2016 and have seen only a few other pilots in IMAC that compete with an electric plane. I just moved up to the Advanced class this year and competed with a new electric IMAC plane, a customized Extreme Flight 104" Extra 300 V2. The plane is capable of flying two Advanced sequences in one flight. That's 20 aerobatic figures with climbs to 1,000 feet or more above the airfield.

I would enjoy hearing from anyone else who has done this with an electric ARF, or any other electric plane. Let me know if you have, or know someone who has.

I finally got some video of me flying the Advanced sequence the other day to demonstrate what this plane can do. Take a look here.
Posted by turboparker | Yesterday @ 02:53 PM | 1,096 Views
Finally able to do the review on Eflite's 2.1m Carbon-Z Cub SS!

Decided to not do an unboxing/assembly review, as there are plenty of those already - plus this plane is straightforward to assemble for those in the target experience range.

This is my first giant-scale electric. My other giant-scale planes have been balsa/ply, and were either glow or gas powered. I have over 30 yrs of fixed-wing RC experience.

Equipment used:
  • Spektrum DX9 Black Edition
  • Spektrum 6s 5000mAh 30C Smartpack
  • Spektrum S1200 Smartcharger


Assembly took me ~1.5 hours. Everything went together well - except a few parts bags were mislabeled. Was fairly easy to figure out what was what.

Binding/initialization/balancing & trimming:

I bound the plane with SAFE disabled. Had to raise the tail to approximately level before it would initialize, though. All surfaces centered-out well when I checked everything out. Spooled her up to check the prop balance, and everything was good - so no prop balancing required on mine.

I ended-up mechanically maxing the rudder throw, and still wanted more rudder authority. I heard that if you bind with SAFE Select, there's a lot more rudder throw available in AS3X-only mode - so, I'm going to rebind & just leave SAFE Select disabled to see if I can get more rudder throw.

I needed to mount the Spektrum 6s 5000mAh 30C pack at the rearmost position in the battery compartment to get the CG back to 120mm aft from the LE at the wing-root. I found the...Continue Reading
Posted by BAF23 | Yesterday @ 02:38 PM | 1,075 Views

In 2014 I stumbled upon an advertisement of a second-hand Fly-Fly F100 in flying condition for what seemed a reasonable price. Some time before that I already had purchased one of the last original kits of that brand because I ever wanted to make a nice model of the French Air Force two-seater I had the chance to fly just weeks before it was phased out. Even as the second-hand one was in a sorry state, I bought it to use as a trainer and eventual source for spares if the need aroused. All of that laid dormant together with other kits and aircraft on my attic for years. End of summer 2020 I had a two week lul in my program and thought that getting the second-hand one ready for some test-flying with various EDFs I had collected would be a useful way of filling that time. Once in my workroom I was very disappointed about the way that model had been very grossly assembled and decorated. The guy I bought it from had been a firefighter at the airbase of Beauvechin and should at least have been familiar with the fact that the USAF star stood on two legs instead of on its head!

Pic 0017c

Speaking of legs, when you see how the nose-gear had been fastened to the fuselage you get an idea about the craftsmanship? of that modeller. I think he used a complete jar of Gorilla type glue on that model. Furthermore duct tape had been used to cover other atrocities before being painted, and during sticker application he had not followed the deep crease lines and after...Continue Reading
Posted by jameschen072 | Yesterday @ 12:12 PM | 1,119 Views
Hey everyone,
Thought you might enjoy this review of the 1/76 (HO scale) Mini by Turbo Racing.
Perfect for those of us stuck at home... race just about anywhere!
Turbo Racing 1/76 (HO scale) Mini- Full Review (6 min 45 sec)

Posted by VE6WEM | Yesterday @ 09:57 AM | 1,152 Views
The Bird of Time is a beautiful and distinctive sailplane dating back to 1979. The plane is nostalgia legal when built to plan, and has a reasonably wide performance envelope, especially for a R/E design. Back in the early eighties, I wanted one but was flying the Maestro Megan and Viking at the time, and really was not doing enough in the hobby to justify building one.

Then the Dynaflite ARF Bird of Time was released in 2003, this piqued my interest in the plane again, but the issues associated with the poorly constructed spar system surfaced. Since it became clear that there was no easy way to beef up the spar on the ARF model, I decided to build a Bird of Time from the kit.

The kit is a real bargain considering that you get pretty good balsa (at least in my kit), with beefy and hard stock on the high stress pieces like root ribs and nice light balsa sheets for the D-tube. Looking at the spar system, it was clear that some improvement could be made, incorporating carbon spar caps and bias fiberglass on the D-tube leading edge. If you are going to modify the wing spar, you might as well do it right. I want to have a wing which is capable of close to 150 lbs. of winch line tension. If this is to be the case, the joiner rod and wing mounting system will have to be improved also.

I am not going to put spoilers on my plane because the original Bird of Time did not have spoilers.

So this kit will be built according to plan but not LSF nostalgia legal with the...Continue Reading
Posted by GroundControlRC | Yesterday @ 07:39 AM | 1,249 Views

Volantex Ranger G2 V757-6 1200mm Wingspan EPO Sport FPV Glider PNF - Fine Tuning Adjustments Session #2

Volantex Ranger G2 1200mm PNF

Volantex Ranger G2 1200mm Kit

Here is a link to the Video:

Tutorial - Volantex Ranger G2 - Fix that bad Thrust Angle

Volantex V757-6 V757 6 Ranger G2 1200mm Wingspan EPO FPV Rc Airplane Aircraft PNP

Volantex V757-6 V757 6 Ranger G2 FPV 1200mm Wingspan EPO FPV RC Airplane Aircraft KIT

Turnigy 2200mAh 3S 25C Lipo Pack (This is the pack I'm flying)

GNB 11.1V 2200mAh 3S 110/220C Lipo Battery XT60 Plug (Not Tested but should work)

URUAV GRAPHENE 3S 11.1V 2200mAh 100C Lipo Battery XT60 Plug (Not Tested but should work)

2 Pieces 8040 Direct Drive Propeller - CW

Banggood GCRC

You Can Help Support Us By Using Our Affiliate Links To The Products Above. A small commission (At No Cost To You) helps us buy more items to review.

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #VolantexV757 #VolantexRanger #VolantexRangerG2 #RangerG2 #Ranger

See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Ground Control RC Glue & Fly Series Scratch-Build Planes

Consider Supporting Our Channel by becoming a Patron at:
Patrons of the Channel will have Exclusive access to Aircraft Plans & Content!

See Us On Youtube | Patreon | RCGroups
Posted by montis | Yesterday @ 05:04 AM | 1,334 Views
ToolkitRC is relatively new company specializing in the chargers and power solutions. They have released a number of different chargers and accessories. The latest released is ToolkitRC M6D charger. Lets take a look at it.


Input voltage: 7.0-28.0V @MAX 30A
Type of battery: Lipo, LiHV, LiFe, Lion@1-6S; NiMh @1-16S; Pb @1-10S
Balance current: 800mA @2-6S
Balance accuracy: < 0.005V
Voltage range: 0.2-5.0V @1-6S
Internal resistance: 1-100mR @1-6S
Charge power: 500W @MAX 25A SYNC
250W @MAX 15A *2 ASYC
Discharge power: 500W @MAX 15A Recycle mode
12W @MAX 3A Normal mode
USB: 2.1A @5.0V [email protected]
LCD screen: IPS 2.4inch LCD 320*240 pixel
Size: 98*68*35 mm

Package contents

ToolkitRC M6D charger comes with USB cable for firmware upgrades, Screen film protector and user manual.

Charger construction

This charger has two battery charging ports and two balancing lead ports for up to 6S. There is a temperature probe (DS1820) port in the middle, but there is no information on its use.

...Continue Reading
Posted by Mandy Chen | Sep 23, 2020 @ 11:18 PM | 1,768 Views
BrotherHobby Hyperbola 701 Frame:

Toray T800SC-24K Carbon Fiber with equilibrum overlay.

Email: [email protected]...Continue Reading