bigoledude's blog View Details
Posted by bigoledude | Jun 11, 2010 @ 03:48 AM | 6,491 Views
You must admit. This is about the coolest landing gear for mounting a pair of wheels to the center of the plane.
Posted by bigoledude | Jun 05, 2010 @ 12:15 AM | 4,028 Views
T-Wolf has some easy-peasy gear here!

Go on! Take some-n-try 'em
Posted by bigoledude | Jun 04, 2010 @ 03:02 AM | 4,379 Views
Glueing to the CF spar is agret idea!
Posted by bigoledude | Jun 04, 2010 @ 02:38 AM | 4,262 Views
You know these are fine! Now, I can even build these. The "O"rings will take some of the brunt.
Posted by bigoledude | Jun 04, 2010 @ 02:25 AM | 4,344 Views
Here are some LG that serve a dual purpose.
Posted by bigoledude | Jun 04, 2010 @ 02:12 AM | 4,256 Views
The LG are cool! But, the plane in the first pic is a little plain!

The 2nd thru 7th pic is a six-part process of making this LG.

Tybrewolf has really put effort into types of landing gear.
Posted by bigoledude | Jun 04, 2010 @ 02:06 AM | 4,250 Views
I like 'em.

My brother used to raise game cocks and would always describe an extremely strong "whatever" as "Cock Strong". When he used that phrase, I knew whatever it was he was referring to, would hold up!

This landing gear will out-last the fire-wall to fuselage connection, I believe?
Posted by bigoledude | Jun 04, 2010 @ 01:38 AM | 4,226 Views
The bigger the plane the heavier the wire!
Posted by bigoledude | Jun 04, 2010 @ 12:58 AM | 4,183 Views
Check out the landing gear and how it attaches to the fuselage. If you have a rough landing, the rubber bands will absorb some of that.
Posted by bigoledude | May 14, 2010 @ 03:12 AM | 4,180 Views
This easy-to-build landing gear works with any narrow fuselage.
Posted by bigoledude | May 10, 2010 @ 09:19 PM | 4,375 Views
Wildweasel contributed this:

"A neat and strong method is to form an 'x' out of cf tubing, the centre point is in the fuse, bound with thread and glued and then supported by ply. The top 'arms' of the x are mounted to the underside of the wings with little ply discs and then small lengths of piano wire are bent to the right shape and glued into the other ends of the tubing to form axles. This is really strong as the UC is supported by three mounting points and provides struts/braces for the wings too.

If any of y'all reading this have other ideas for landing gear, please PM them to me."
Posted by bigoledude | May 10, 2010 @ 09:06 PM | 4,534 Views
Davereap shared more landing gear designs

He writes:

After a bit of thought ive also made a trike system

In reference to the 1st pic:
"simple two part construction"

2nd pic:
"The wooden plate is thin ply 2" wide.. this takes two strips of velcro just nicely..And will fit on a Fuz of 2" upwards in width"

3rd pic:
"shown here the U/C is in two sections and is bound using fishing/dacron or upholstery thread, which is CA'd to fix"

Then Davereap gave us this

Twin legs for a flat bottom wing

Heres another one that ive made..Used for my 36" KFm4 Nutball or any plane that is built with a flat bottom.

The triangle of velcro holds it very well - its a b.... to get off

make the UC to the size and weight you require...

I used 2mm ply and a heavy gauge wire on the one in the pictures. it added 3oz and was for a plane that already weighed 25oz ... so the AUW was 28oz

an alternative to the triange shape would be a T shape for the ply, with all the bars 1" wide to take the velcro..
I required a heavy unit so just made a simple triangle shape
Posted by bigoledude | May 10, 2010 @ 08:49 PM | 4,327 Views
Davereap gave me more ideas for landing gear. These designs flipped me out!! I kept thinking of planes to build just to use this stuff!

He wrote:

Removable Under cariages U/C's designs (for planes with narrow spline fuz)


I thought I would show a couple of my ways to hold those wheels.

The actual wheels are held on to the wire with a bit of silicone fuel tubing each side...and they have stayed on ok so far in use..for thin wires fix the tubes with hot melt glue

Both removable wire UC systems have proved usefull and all work a treat..

System for planes with a lower spline

1...Two wheels at the front type.. the bends are shown below.. the cross body lengths can be made to the width of your fuz..
The V section goes up the outside of the fuz then you use a rod to hold it in can have shorter V lengths but the longer one like mine spreads the loading ..A short one will damage the depron in a heavy landing/crash

Figure 1
The V section that fits over the spline can be made shorter, but then it can more easily cause damage in a heavy landing

Figure 2
By adding some very thin ply and having a long V, stresses are much better spread out..

Figure 3
The trike version has a front leg bending that is bound to the existing two leg version.. then you just mount it round the other way..with the one leg at the front..simple...

Figure 4
this will fit on any splined fuz design
Posted by bigoledude | May 10, 2010 @ 08:14 PM | 4,389 Views
Here is Rusty's LG
Posted by bigoledude | May 10, 2010 @ 08:09 PM | 4,231 Views
I asked around, for some ideas on building landing gear for foam planes and got some great ones!

When I started this blog, it did not occur to me that everything is scrolled backwards. This thing reads from bottom-to-top. So, if it seems a little goofy, it's only because the guy that wrote it is a LOT goofy! Me!

Rusty says:

I use a simple method of bending the wire into a square 'U', but upside down. The size of this square is about half inch wide, maybe one inch tall.
within this square (rectangle, actually) I insert a proper sized piece of thin plywood. I drill holes around the sides of the ply and sew it on with dental floss. Then add epoxy.
Once done I wrap the ply area of the gear wire with a short length of duct tape, maybe four inches long (even a bit shorter). This wrapping is to add thickness to the ply, and can make a clean-up by removing the tape when installing the gear to a new plane.
I then cut a proper sized slot in the profile fuse, and hotglue in the gear. See pic.
Attached Thumbnails 46.8 KB Views: 88