Safe settings for ELRS:

Transmitter (Tx)

Mode: CRSF
BAUD: 400K
for EdgeTx: ADC filter OFF

Original crystal-controlled radio goes back in this update. Futaba 3PM-FM, R133F 75Mhz receiver using channel 72FM crystal set. 12in. antenna pipe gets its own mounting bracket. These images show the purpose 1/8in gap between the frame rails that allowed for attaching various mounting platforms while allowing adjustability for weight balance.

Receiver also gets a Novak 'Glitch Buster' from archive storage. Without it, battery voltage near the end of a run would draw down below critical need for steering servo. Glitch Buster just enough to prevent that.

Steering servo is a HiTec micro metal gear - original install still in place. Servo saver is a New Era item and part of the steering system.

Original install had velcro receiver mounting. Double side tape for this install since it is primarily a static display resto. Cheers. Arnold

[Edit. If image appears bluured, please click on the image for a more clear view.]

Took my DLG to the slope, lights winds perfect for smaller planes

Aurora DLG, slope soaring (2 min 21 sec)

I've previously written about the Sperry Messenger however given the airplanes unique story, I chose to give it a slightly deeper dive.

Sperry M-1 Messenger: Since an original Sperry hasn’t flown anytime in recent history and it’s begun to fade from a lot of memories, however in its day it was a very relevant airplane.

The Sperry Messenger first flew in 1921. A critical time for airplane development. WWI had just ended and it was clear that airplanes had a future in war. The race for aviation development was on. The Messenger hit the market with just the right recipe at just the right time. It was simplistic and cheap as well as a very good performer for its era being powered by a Lawrance 3 cylinder radial of 60hp.

The airplane was designed by the capable hands of Alfred Verville on commission for the Army Engineering Division at McCook Airfield in Dayton Ohio. The concept of the design was to be a small runabout that could deliver messages similar to a military motorcycle courier. This led to the naming of the new M designation in military aircraft for Messenger. A designation that only the Sperry ever carried. Officially called the Engineering Division M-1, the design was contracted to the brand new Lawrence Sperry Aircraft Company from Farmingdale, Long Island, New York.

Sperry delivered the designated prototypes for testing and satisfied with the results, the engineering division ordered 5 production examples. A total of four more contracts were issued...Continue Reading

K235

From a just-received AMA email:
It was September 16, 2023, now it's March 16, 2024.

🧐Yep Les Amis,
Du Taz-Atelier au Taz-Tech ... Je prends mes marques (c'est pas encore ça, lol !)
Pas facile de se faire à un nouvel environnement de tournage et une nouvelle façon de travailler mais ça devrait être pas mal quand tout sera au point je pense ... J'éspère !
J'ai en test aujourd'hui, deux produits liés à l'alimentation de nos appareils, le BEC SpeedyBee et une powerbank de 50 000mAh 65W, la Rophie. Fonctionnement, qualités et défauts, voici ce que j'en pense et chacun pourra se faire un avis selon ses préférences et besoins ... Prenez soin de vous (et des autres) et merci à tous pour votre soutien .

Powerbank 50000mAh 65W PD & SpeedyBee BEC - Review Test Démo - Y a du nouveau !!! (11 min 34 sec)

🧐NOTATAZ : 17,5/20 Bonne impression globale !!!

- Rophie POWERBANK : https://amzn.to/44QLsHv
Code promo : 23BT4V7X 15 % de réduction jusqu'au 12/10/2023

- SpeedyBee Bec : https://www.banggood.com/custlink/KD3tH0hqv1
- Buzzer testeur lipo : https://www.banggood.com/custlink/vKmHi0ddli

- Ma caméra OBSBOT TAIL AIR (KickStarter) : https://obsbot-tail-air.kckb.st/d3409add

- AIDER la chaîne avec un don (tous les dons servent à alimenter les vidéos en produits, cadeaux concours ou matériel ) : https://streamlabs.com/Tazkiller85
- TABLEAU de Coupons et Promos : http://bit.ly/40AKFZy
- VENTES FLASH Banggood : https://www.banggood.com/custlink/KK3EkrUEU7
- SOLDES D'ANNIVERSAIRE BANGGOOD du 4 au 10 SEPT : https://...Continue Reading

Well - its not the lightest ASW28 flying - and probably not the straightest/smoothest - but its flying and I am enjoying it!

I just wanted to share a couple photos - and see if anyone else is still flying one of these kits!? I bought this a few years ago - but finally got around to building it and now flying it. Its been 30 years since I last flew a sailplane - sooo.... having to get use to the slower/wider lofting turns.

Mods include: Ez removable canopy - via spring pin
Longer/wider control surface - the original looked more like little spoilers rather than control surfaces.... however I used .020" Polystyrene - top and bottom - and it added a lot of weight. I think if I could do it again I would have just done one side - probably the top. If that created a little drag - I would still be ok with that - I'm not looking for all out speed.
Tinted Canopy
Built-in Wing servo lead connectors
Robart Pin Hinges on all control surfaces


Its a slightly bigger motor, bigger prop flying on 2200mAh 3S.

My first Blog post here - sooo... I'm not exactly sure how to do this - so I'll start with this! Thanks for taking a look.

I know a few people talk about the CG being a problem - but this plane was spot on. (probably because of all my control surfaces additions)

Episode 181: "Detours" is now live!
http://www.rcroundtable.com/podcasts...pisode_181.mp3

In this episode Lee and Terry talk about a really cool hobby shop and a really cool event.
-Dynamic Balsa (6:10)
-Warbirds and Classics (33:10)
-FRIA update (51:50)

You can visit our website at RCRoundtable.com to listen over the web or download an MP3 of the show. Or, you can subscribe to RC Roundtable on iTunes.

We would love to read your comments and ideas. Please drop us an email: contact@rcroundtable.com

RC Seaplane from the movie WATERWORLD SCRATCH BUILD MAIDEN. Full 3D printed Bambu Lab AERO PLA plane (25 min 4 sec)

Here's my configuration for a Spektrum Smart AS3X/SAFE receiver in the E-flite 1.5m Air Tractor.

1. There are three Flight Modes (FM). FM1 is SAFE mode with self-leveling and bank/pitch limiting, FM2 is AS3X only, and FM3 is Gyro off.
2. All AS3X and SAFE mode gains are set to Fixed. No Gain Channel has been selected. Heading Hold and Panic mode are disabled.
3. The AS3X gains in FM1 and FM2 are set to 20% for roll, 40% for pitch, and 60% for yaw.
4. The SAFE mode gains in FM1 are set to 30% for roll and 50% for pitch.
5. The SAFE mode angle limits are set to 70° of bank to the left and right, 40° nose down, and 50° nose up.
6. The attitude trim for roll is 0 degrees. The attitude trim for pitch is 2° nose up.
7. The High Throttle-to-Pitch mix starts at 80% of throttle and increases to an angle of 8° nose up at full throttle.
8. The Low Throttle-to-Pitch mix starts at 30% of throttle and increases to an angle of 12° nose down at idle.
9. The flight mode channel is set to channel 9. If your transmitter has fewer channels, move it to an unused channel.
10. The receiver orientation is set to "Label toward the Sky", Pins toward the Nose".

Notes:
1. SAFE mode requires 100% travel on the aileron and elevator channels in order to work correctly.
2. Verify that the transmitter sticks move the control surfaces in the proper direction.
3. Verify that the gyro moves the control surfaces in the proper direction by tilting the plane 45° left, right, nose down, and nose up.
4. Use at your own risk! Since I'm not there, I have no control over what might happen.

I picked up a pre owned TC 1700MM but the nose gear wasn't working properly. I have managed to get it back together however can't figure out how to get the nosewheel attached to the servo so it turns with the rudder. Does anybody have info on how to get this hooked up properly or any pictures? I would appreciate it.

Here’s the newest addition to my collection. A Tamiya Bruiser (2012 re-released edition). I went completely stock, and went with the recommended Tamiya paint colors as well. I added some interior parts from Axial, custom made some door cards, and used Cortney ‘Cover Girl’ Creigor as my driver. I spent 16 hours on the paint alone, so this will be a soft runner for sure.

Something a little different. In this video I repair a jammed Dubro fuel pump and improve my fuelling station so It doesn't come loose all the time (the lock ring didn't allow the nylon nut to engage properly)

Gear Repair Ep 1 - Dubro Fuelling Station (23 min 8 sec)

Attention all RC enthusiasts and off-road adventurers! Get ready to take your remote-controlled car experience to the next level with the amazing SCX24 40's 4 Door Dodge Power Wagon. This scaled-down version of the legendary Dodge Power Wagon is built for rugged terrains and thrilling adventures. In this blog, we'll explore the impressive features and capabilities of the SCX24 40's 4 Door Dodge Power Wagon and dive into the world of 2S batteries that perfectly complement its power and performance.

The SCX24 40's 4 Door Dodge Power Wagon: A Beast on Wheels The SCX24 40's 4 Door Dodge Power Wagon is an astonishing 1/24th scale RC truck that combines style, toughness, and versatility. It boasts an incredibly detailed exterior design, faithfully recreating the iconic Dodge Power Wagon's features, including the imposing grille, rugged bumper, and eye-catching fender flares. With its rock crawler capabilities, this mini monster truck is ready to conquer any terrain you throw at it.

Key Features of the SCX24 40's 4 Door Dodge Power Wagon:

Fully equipped and ready-to-run
Assembled SCX24 chassis, drivetrain, and suspension
Detailed Power Wagon 4-door molded ABS hard body
Pro-Line Interco Super Swamper tires
Pro-Line Impulse Bead-Loc wheels
Batteries available for SCX24 40's 4 Door Dodge Power Wagon

The SCX24 40's 4 Door Dodge Power Wagon is typically compatible with a 2-cell 7.4V LiPo (Lithium Polymer) battery. 2s LiPo batteries offer high power output, excellent...Continue Reading

SkyfendHunter AFA100, a new handheld anti-drone jammer that combines surveillance and jamming technology two-in-one. Skyfend AFA100 can do drone full-band signal interference, shield drone radio signals and GNSS signals, with a 3.5-inch display screen, portable transportation, and is a new star in the anti-drone market!

SkyfendHunter AFA100 is compact and efficient. As a handheld anti-drone signal jammer, it weighs 6.5kg and measures 773 x345 x114 mm. It exists in the form of an anti-drone gun. There is also a load port on the top of the jammer. Can be used to connect scopes.

Note that the scope is not an accessory in the fixed set, it is an optional accessory!

SkyfendHunter AFA100, as a two-in-one drone signal jammer for detection and interference, can strongly and effectively interfere with 400Mhz-6Ghz radio frequency drones, and can conduct targeted strikes against 2.4Ghz and 5.8Ghz drones, which means, You don't need to adjust the frequency band, just manually press the Trigger to make the drone land or return.


SkyfendHunter AFA100 anti-drone signal jammer: https://www.autelpilot.com/products/...i-drone-jammer


The SkyfendHunter AFA100 anti-drone signal jammer has a built-in 3.5-inch display screen, on which you can see drones coming from any direction. With the help of the scope, you can better focus on the jamming band for drone jamming. Eliminate the Drone Threat!

The more important point of Skyfend AFA100 anti-drone signal jammer is that it supports user log upload and software update, which will be updated in real time to cope with drone changes!

With the ubiquity of drones, it is necessary to use anti-drone signal jammers to deal with political turmoil, but the use of signal jammers must be legal and compliant to avoid public safety accidents.

AGFRC SA30BHM is brand new mini size servo but with a standard servo 25T output shaft smart. It is fit well with 1/12 pan car, also perfect for more RC models like electric motorcycle, Robot, mini crawler, Buggy and Airplane etc.

This servo only 32g super light weight with full CNC aluminum case. The skillful use of the combination of steel gears and titanium gears, not only durable but also can maintain light weight. The high power brushless motor make it can out the high torque of 11.50kg-cm and the fast speed of 0.060sec at 8.4V. SA30BHM is a programmable smart servo, it allow to change to the firmware for regular and winch servo usage via our programmer card. Thanks to the programmable function, there are also many Settings that can be adjusted in the programming software, such as the over load protection, soft start and the inversion etc.

Specification
Model Name: SA30BHM
Operating Voltage: 4.8-8.4 V
Operating speed: 0.100sec/ 60° @ 4.8V
Operating speed: 0.082sec/60° @ 6.0V
Operating speed: 0.068sec/60° @ 7.4V
Operating speed: 0.060sec/60° @ 8.4V
Stall Torque: 8.0 kg-cm (111 oz-in) @ 4.8V
Stall Torque: 9.0 kg-cm (125 oz-in) @ 6.0V
Stall Torque:10.50 kg-cm (145 oz-in) @ 7.4V
Stall Torque:11.50 kg-cm (159 oz-in) @ 8.4V
Gear: Steel+Titanium
Motor: Brushless
Size: 29*14*29mm(1.14*0.55*1.14 in)
Weight: 32g
Connector Wire: TYU 180mm / 26AWG

If your are interested in it please feel free to contact us: agf.sales04@agfrc.com

Brand: HRB

Capacity: 9500mAh

Cells: 4S

Voltage: 14.8V

Continuous discharge rate: 120C

Size (L*W*H): 166x51x42mm（Pay more attention the size. make sure you can use it.）

Weight: 771g

Plug: EC5 female plug

Charging Rate: 4.75A-9.5A

Power: 140.6Wh

Link(US STOCK): https://www.ebay.com/itm/115631872570
STORE: www.hrb-power.com

AGFRC New Product SA30BHM 11.5KG Smart Winch Servo


AGFRC is always keen on innovation, and we do not just make servos, but we offer high performance servos for each specific fields. For example, our popular A81BHMW 45KG 0.085s BLS waterproof servo for 1/8 rc cars.
After long time testing, the SA30BHM 11.5KG 0.050s 8.4V HV smart winch digital programmable brushless servo is ready for the market, and it is special design for the 1/12 Pan cars.


For the external structure:
The SA30BHM is only weight 32g with fully CNC Aluminum case, very strong and durable.

For the internal structure:
As we know, more torque can meet more challenges, so we have tried many brushless motor to bring higher torque, and here we has 11.5kg powerful strong torque. Then we come to speed, the SA30BHM is 0.060s fast, it will be very smoothly operation for its double ball bearings.
The SA30BHM comes with the 25T spline titanium gears, very high strength and not easy to be weared.
...Continue Reading

Had a great time with our belgian, dutch, french and german friends at the field of belgian Les Accros du servo. Fantastic venue.