Andrey_Rakhmanov's blog View Details
Posted by Andrey_Rakhmanov | Sep 13, 2019 @ 06:22 PM | 1,445 Views
For my pilotage 2-engine Arlequin I manufacturer square cockpit canopy. The canopy protects model electronics compartment from dust and moisture.
Name: Ready.jpg
Views: 0
Size: 1.28 MB
Description:
It is quite easy to do, I briefly describe describe the process by several photographs.

First we need to prepare pressing form. I cut parts of the form from 4 mm polystyrene sheet.
Name: Parts1.jpg
Views: 0
Size: 181.0 KB
Description: ...Continue Reading
Posted by Andrey_Rakhmanov | Sep 10, 2019 @ 05:13 PM | 671 Views
Milling carbon fiber (3X speed) (2 min 1 sec)

I have a need to cut carbon parts for my airplane models and decided to create CNC capable to do carbon cutting.

Requirements for the machine:
  • Total price of components less than $300.
  • Weight less than 15 kg (30 pounds).
  • Should cut A4 size carbon sheet with precision about 0.1 mm.
  • Should be portable and environment friendly - designed to do cutting and to be stored in the apartment living room,

Finally I found cheap CNC ($125-$225) on banggood and re-designed it:
Name: stanok.jpg
Views: 13
Size: 324.3 KB
Description:

Major improvements:
  • 500 Watts spindle ($50-$80).
  • Vacuum cleaner hose attached($10).
  • Bridge Cable Chain($10).
  • LED work zone light.($10)
  • New couplings and bearings($10-$20).
Name: motor.jpg
Views: 9
Size: 31.6 KB
Description: ...Continue Reading
Posted by Andrey_Rakhmanov | Jul 22, 2018 @ 05:14 PM | 2,678 Views
Previous stabilization scheme for the 2-engine Arlequin used Eagle Tree Guardian flight stabilizer. This stabilizer is quite old (more than 10 years) , so I decided to replace it with a more modern and popular one. It is not easy to do because very few stabilizer can match qualities of Guardian. Finally, the choice fell on a popular receiver with built-in stabilizer - FrSky S8R.



I tested FrSky S8R with classical scheme model, and what I found:
Pros
- Relative small price - $ 40 - $ 50 - 8 channels for a telemetry receiver with stabilizer isn't bad!
- It has telemetry channel - it is possible to measure the voltage of the battery.
- Can output data in SBUS format - allows to avoid PWM wires mess. Now receiver can be connected with one cable.
- An ability to do full configuration directly from the transmitter (Taranis + Lua scripts).
- A large number of flight modes (3D, horizontal stabilization, hover, knife).
- Active support from FrSky - new firmware releases, utilities, etc.
Cons
- Receiver configuration menu features minimum possible number of settings.
- Complex and unobvious processes of installation, configuration and calibration - for the understanding it's better to watch the video on YouTube.
- Support - only 3 basic types of plane models (classic, delta wing, v-tail) 'hover' and 'knife' flying mode aren't enabled for delta wing and V-tail type models.
- Not very obvious stabilization scheme. Impossibility to set the "general"...Continue Reading
Posted by Andrey_Rakhmanov | Jul 20, 2018 @ 04:47 PM | 2,359 Views
I usually write posts in Russian for www.rc-aviation.ru. Now I decided to start mirror publications in English here . I am placing below links to old rc-aviation articles - if someone needs to translate them in English - translate.google.com does good job here.

Latest version specifics - Arlequin III http://rc-aviation.ru/make-model/pho...95-arlekin-iii
Previous version (review)- http://rc-aviation.ru/make-model/108...i/1886-arlekin
Previous version (building) - http://rc-aviation.ru/make-model/pho...n-izgotovlenie
Previous version (pre-flight tuning) http://rc-aviation.ru/make-model/108...ekin-nastroika
2 engine signal mixer building and programming - http://rc-aviation.ru/mtech/komp/181...uino-micro-pro