R/C Blogs - RC Groups
Shop our Airplanes Products Drone Products Sales
Posted by alex111 | Today @ 06:29 AM | 66 Views
A few new boats to add to my collection
Posted by lyxlens | Today @ 02:01 AM | 177 Views
1/3" 222Degree Fisheye Lens 0.76mm 8MP M12 Mount Wide Angle Lens for Panoramic 360 VR Action Camera Sport DV Lens Replacement
Specification

Model: lyx0.76

Sensor: 1/3" φ 2.8mm
Focal Length: 0.76mm
Optical BFL(BFL): 2±0.2
Mechanical BFL(MBFL): 1.5±0.2
F/NO.: 2.1mm
Optical BFL(AIR): 1.9±0.2
Mechanical BFL(AIR): 1.4±0.2
FOV(D/H/V): 222°
Distortion: 〈-97.2%
Relative Illumination: 〉50%
Construction: 2G4P+1IR
Cut Frequency At 50%: Tabs〉90%at 420-630nm,T=50% at 650±10nm,T〈5% at 680-1100nm
Thread: M12*P0.5
Chief Ray Angle: 〈11.4°

Link: https://www.aliexpress.com/item/1-3-...862771467.html
Posted by Boone 870 | Yesterday @ 11:31 PM | 234 Views
… continued

Priority number one for modifying the transmitter would be to place the gimbal assemblies far enough apart to prevent my hands and stylus from contacting one another while flying. Second priority was to place the various switches on the transmitter into positions that would allow me to either bump them or hook them with my fingers to select different flight modes and channels.

The first serious idea that I considered was to strip all of the electronics out of the case of my new Spektrum DX6 and cut out holes for the gimbals, display screen and all the various scrolls and switches in a wide, thin piece of Lexan in a configuration similar to a Jeti DC-24 transmitter but spread out wider and longer. I ran the idea by my cousin, who has professional experience designing and building electronic panels, and he thought it would be something that could be done and was willing to tackle the job.

While I was thinking about what I thought would be the best layout for the gimbals and switches on the planned Lexan board, I asked my cousin to modify the case on my DX6 as it was currently configured by cutting off the plastic horizontal antenna housing/carrying handle so that my transmitter could lay flat on the current Lexan board I'm using. When we opened up the transmitter and got a look at just how complicated the transmitter was and how much work it would take to place all the individual electronics onto a Lexan board, I decided it would be a good idea to go...Continue Reading
Posted by Reckless_fpv | Yesterday @ 09:29 PM | 277 Views
Posted by Les Walter | Yesterday @ 09:05 PM | 273 Views
I building a hexacopter RD 290, but Id like to change the flight controller for a Matek F722-STD, but I could not find any article yet how to wiring up for the Matek for 6 motors. Do I need an other PDBord for it or not? Or need any other card yet? Im a bit confused...... Sorry. Could you help me to show the end of the tunnel????? Pleeeeeeeeezz.......Thanks for your understanding and cooperation. Les ( leslesles999@hotmail.com )
Posted by BDOG1 | Yesterday @ 08:16 PM | 310 Views
I got out for some "spring flying" on our hill after work today, 37 degrees 18 mph wind and snow...Yup I Love New York

Had one to maiden,cant say it went well.
Acted very tail heavy added a bunch of nose weight,barely flying ,conditions were not fun and tired after a full work day...I will get back to it

Then I put The Knife Edge up
This Plane just kicks Butt !
spent the next hour or so ripping with it,gusts that rocked me on my heels ,crossed and bumpy ,sink, snow ,grovel you name it the KE just does it .

Flying it in close on the top of the hill and standing it on a wing tip , pulling elevator to do a paper clip turn ,it seems to accelerate thru the turn like it was shot out of a canon,I think it is the flex in the wing loading up and then unloading like a slalom ski.....
Great way to end the day
Posted by QuadifyRC.com | Yesterday @ 07:09 PM | 341 Views
It's been a good while since Gearbest have had any good quad specials on, I noticed their website has improved so maybe that is where the focus has been. Anyway I've posted my pick of specials below at http://quadifyrc.weebly.com/coupons-and-discounts.html

I like the fact that both the TX200 and an OEM CCD micro camera are both on special meaning you can upgrade your AIO camera in your brushless micro to a CCD cam with variable power vtx for less than $30. More details on this here for the leader.

Emax BabyHawk R for $122

Tattu 3s 450mah battery for $9

Tattu 3s 850mah battery for $12

Tattu 3s 850mah battery for $16

Leader 120 PNF 2.5" brushless quad for $110

Full Speed TX200 25/200mW VTX $10

Furibee MS Micro CCD Camera $18

HAKRC 20A 4in1 2-4s 20mm ESC $17

Whoop pro f3 light controller with OSD $18

Emax LHCP pagoda antennas (pair) $5


....Continue Reading
Posted by Bill M - RC | Yesterday @ 12:23 PM | 650 Views
Hi fellow pilots

Here is a short video to see a basic teardown and how to repair the gimbal on the Dragonfly Pro should you need to:

Simtoo Dragonfly Pro Gimbal Repair (7 min 2 sec)

Posted by JohnVH | Yesterday @ 10:10 AM | 702 Views
HK Swamp dog on SNOW!

HobbyKing Swamp Dawg Air Boat on SNOW! (5 min 4 sec)


Get one at Hobby King: https://goo.gl/ndd12S
Posted by 14bissar | Yesterday @ 07:47 AM | 793 Views
i have a 450 mm quad with betaflight f4 and simonk esc and 2212 motors.
when i take off my copter starts yawing aniclockwise.the trims do no good and it is so very fast that stick corrections are very difficult for a bigginer like me.
please help.
Posted by mlilasic | Yesterday @ 05:35 AM | 866 Views
Review (ip) of Dragonfly Booster 5.8G 3dBi TX/RX FPV Antenna RP-SMA/SMA



Description:
Better signal quality and much more durable.
These Dragonfly Booster antennas can be survived from the hardest crashes with the specially designed cover and silver connector.
Three different sizes (5cm, 8cm and 11cm) in SMA and RP-SMA are selectable to meet your special needs for the build.



Specification:
Frequency Range: 5400 ~ 5900Mhz
Impedance: 50Ω
V.S.W.R: ≦1.5
Gain: 3 ~ 3.5dBi
First Upper Sidelobe Suppression (dB) ≥15
Front to Rear Ratio (dB) ≥25
Cross-polarization Discrimination (dB) ≥15
Port Isolation (dB) ≥28
Polarization: Vertical/Horizontal
Maximum Input Power: 10W
Cable: RG141
Color: Black
Connector: RP-SMA / SMA (Optional)
Length: 5cm / 8cm / 11cm (Optional)
Weight: 10g / 11g / 13g




Grab yours Dragonfly Booster antenna HERE.



TODO:
DVR flight...Continue Reading
Posted by FPV.Model | Yesterday @ 04:37 AM | 896 Views
FPVMODEL Flash Deal!
Save up to 80% OFF.
Unbelievable saving, limited time!
Hurry before they are sold out!


Dragonfly 5.8G 48CH 25/200/600mw Stackable Video Transmitter

LAST DAY ! ONLY $6.99 NOW!
Name: s-20161230143301-7350.jpg
Views: 0
Size: 11.2 KB
Description:

Dragonfly 5.8G Receiver Module for Fatshark Dominator FPV Goggles

LAST DAY ! ONLY $5.99 NOW!
Name: 20170116151306-8386.jpg
Views: 0
Size: 27.3 KB
Description:

RaceFlight F4 Flight Controller V2

LAST DAY ! ONLY $29.90 NOW!
...Continue Reading
Posted by cuavlindy | Yesterday @ 03:53 AM | 899 Views
Xtend XTP9B DPS 001PIX Wireless Data Transmission Module Kit RF Box 900mAh 1W for PIXHAWK/PIXHACK Flight Controller

Xtend XTP9B DPS 001PIX Wireless Data Transmission Module Kit RF Box 900mAh 1W for PIXHAWK/PIXHACK Flight Controller

Specifications:
- Model:Xtend-XTP9B-DPS-001PIX
- Indoor/city distance (with 2.1db antenna): Up to 900m
- Outdoor/wireless visible distance (with 2.1db antenna): 15-22km
- Sending power output: 1mW-1W(0-30dB)
- Seriel transmitting speed: 10-230, 400bps
- Receiving sensitivity: -110dB(@9,600BPS),-100DB@115,200BPS
- Transmitting speed: 9,600 or 115, 200bps
- Wireless RF transmssion speed: 125kbps
- Working temperature: -40~85 degree C
- Working frequency: ISM 902-928MHz
- Spread specrum: FHSS
- Networking topology: Peer to peer,point-to-point,point-to-multip
- Channel: 10 hop sequences share 50 frequencies
- Encryption: 256bit /128 BIT AES
- Voltage: 2.8-5.5VDC
- Receiving : 35mA
- Certificate: FCC,IC, C-TICK
- Size: 7.5*4.6*1.7cm
- Antenna weight : 24g
- Module weight: 29g
- Shell: 47g
- Total weight: 100g

Features:
- CNC XTEND shell, high quality
- 57600 baud rate with flight controller, distance over 20km
- Baseboard with USB port and TTL interface
- Working band ISM 900M, 115.2kbps, with a RPSMA antenna interface
- FHSS technology, transmitting power software adjustable 1mW-1W
Transmit power output 1mW 10mW 100mW 500mW 1W
Power voltage 2.8-5.5VDC 2.8-5.5VDC 2.8-5.5VDC 3.0-5.5VDC 4.75-5.5VDC
Transmit current (5V) 110mA 140mA 270mA 500mA 730mA
Transmit current (3.5V) 90mA 100mA 250mA 600mA N/A
Specifications:
Size (mm):84*46*17
weight: 39

package weight:300g

Package including:
- 2 x Data Transmission Module with shell
- 2 x Antenna
- 1 x Connection cable
- 1 x USB data cable


more details as below:

https://www.aliexpress.com/store/pro...40de109daiwTZr
Posted by Anshumanyl | Yesterday @ 12:07 AM | 964 Views
I have bought nei 6m gps module . It has a only red light. Whenua I power the module that les just vinod one and then it is off.
Why is this?
I think it is searching for satellites
Or
The module is not working .
It blinks when i go outdoors .
Posted by unrauv | Apr 18, 2018 @ 07:04 PM | 1,052 Views
Hi All

Here are some images I have put together of my new EDF jet design, free plans coming soon...
Any input fro people in the know world be helpful as this it my first jet design.

Wing Span : 1220 mm
Fuse Length : 1036 mm
EDF Motors : FMS 2 x FMS 50mm 12 Blades Ducted Fan EDF
ESC : 2 x 40Amp 3C or 4C
Battery : ZIPPY Flightmax 5000mAh 3S1P 40C or ZIPPY Flightmax 3000mAh 3S1P 40C
Battery : ZIPPY Flightmax 4500mAh 4S1P 45C or

Vincent Unrau
All plans are free
www.rcfbaircraft.com
https://www.facebook.com/foamboardaircraft/