Posted by fredmdbud |
Mar 12, 2024 @ 11:01 PM | 6,867 Views
Acrylic floor glosss. Dries clear, apply multiple coats for hardness.
Posted by fredmdbud |
Oct 08, 2023 @ 03:45 AM | 5,473 Views
Designed around high-power surface-mount LED packages. Permits surface flush mounting or recessed with a common lead.
Posted by fredmdbud |
Aug 24, 2023 @ 09:20 PM | 10,312 Views
Goal is to 3D-print a new housing
Posted by fredmdbud |
Aug 09, 2023 @ 03:01 AM | 20,536 Views
Posted by fredmdbud |
May 07, 2023 @ 10:47 PM | 7,879 Views
Posted by fredmdbud |
Apr 12, 2023 @ 10:48 PM | 7,328 Views
Posted by fredmdbud |
Dec 14, 2022 @ 12:03 AM | 14,114 Views
Initial concept for the catapult shuttle. Since the plane doesn't have a launch bar, it operates as a push instead of a pull on the nose gear.
Posted by fredmdbud |
Sep 07, 2022 @ 12:19 PM | 10,376 Views
Reduces the number of cables needed to run between two points.
Possible uses:
- Wire management (e.g. receiver in front, servo junction in middle)
- With female connector housing bonded, a multiple-servo quick connect/disconnect
Posted by fredmdbud |
Mar 16, 2022 @ 12:06 AM | 25,040 Views
Deploy on ground only. Actuating with the throttle-cut switch ensures no power applied during braking.
Posted by fredmdbud |
Feb 06, 2022 @ 03:23 PM | 32,579 Views
Adding wingtip navigation lights, on both dorsal and ventral sides using parallel diode arrays.
Lighting will take advantage of MCB-E’s separate channels for regular always-on and “takeoff lights” to have strobe lights with gear down, with a simple insertion circuit requiring only minor modification to the cable harness.
Posted by fredmdbud |
Dec 30, 2021 @ 09:28 PM | 70,838 Views
Charging two 3S batteries using a single charging port.
Preferably using matched batteries with similar capacities, C rating, initial voltages.
Can also use a multiple balance board, using both 3S and 6S connectors, battery with GND lead using the 3S, and the battery with + lead using the 4 pins of the 6S on the left (looking at the board’s JST-XH connector with the notches on top).
Posted by fredmdbud |
Jun 25, 2021 @ 10:26 PM | 38,644 Views
Posted by fredmdbud |
May 16, 2021 @ 09:11 PM | 39,133 Views
Alternative to soldering probe wires to the battery leads
Posted by fredmdbud |
Jun 09, 2020 @ 01:34 PM | 23,419 Views
Can be used as dust covers or used-battery indicators.
https://www.thingiverse.com/thing:4440894
Posted by fredmdbud |
Jun 08, 2020 @ 10:00 PM | 18,421 Views
Can be used as dust covers or used-battery indicators. Can be used with XT-90 if made with flexible filament.
https://www.thingiverse.com/thing:4439507
Posted by fredmdbud |
Aug 18, 2018 @ 05:32 PM | 18,289 Views
- $1.50 electronics part, can be connected between end connectors on balancing plug, or soldered directly on ESC battery plug for voltage.
- Permanently mount in battery compartment of larger planes for instant before-and-after flight voltages.
https://www.sparkfun.com/products/14313
Posted by fredmdbud |
Aug 13, 2018 @ 01:41 PM | 17,459 Views
Mount on visor, tabletop or ground