Posted by scousethief | Today @ 06:17 AM | 15 Views

PRE-ORDER has begun , i WILL be reviewing this as soon as it arrives

ZOHD Dart XL Extreme FPV Aircraft RC Airplane PNP

Brand Name: ZOHD
Item Name: ZOHD Dart XL Extreme


At ZOHD we take very seriously the feedback from our fans and friends around the world. Dart XL Extreme was the answer from the company to all of those pilots who loved their ZOHD Dart but wanted something bigger.

Instead of going the easy way and just scale up our highly acclaimed Dart, we raised the bar for ourselves even higher: Lets create the best swept-forward FPV wing ever made, and lets do it right now!

Featuring and incredible set of high quality and ORIGINAL innovations, we intended to give you the ultimate FPV wing for mid and long range. Performance and portability where always on the table, but we didnt stop there: without cutting any corners we went straight on for environmentally friendly materials 100% biodegradable, metal gear servos, high quality power plant, protection for leading edges and skids, vortex generators, revolutionary multi-cam hard nose and much, much more. Check below the full list of features and specs. This is it! ZOHD Dart XL Extreme is ready to hit the skies around the world, and this is just the beginning join us in this incredible adventure.

Note: This plane will come out soon, and we will update the descriptions then.

Package Included:
1x ZOHD Dart XL Extreme PNP
Posted by rogerjiangcf | Today @ 05:52 AM | 20 Views
Background info:
I have recently bought nolimitdronez mod software trying to remove the maximum height limit of my Mavic. Downgraded from V01.04.0400 to V01.03.0900 in order to get the height limit removed. Planning to test the limits in the countryside of course. However, the firmware of the controller is on V01.04.0400 and has not been touched. I'm was using the MODDED DJI GO APP (For the first time).

Before crash:
I was flying my Mavic on a grass field 100 meters away from a tall building to take a look. Everything was working normally and suddenly the motor stopped working or a prop flew off or something. The aircraft started spiraling down, I tried to restart the motors with success but according to the log file my Mavic fell even faster after the attempted motor restart.

My Suspection:
I either lost a prop in flight or it was the MOD that caused it. However, I would like to know the exact cause.
I have checked the log file and there are quite a few errors. Such as MOTOR IDLE, GPS POSITION NO MATCH, there was also missing data for 16s right before the motor went out.

Note: NO ONE WAS INJURIED! My Mavic crashed on a grass field and there was no one around(Except for me). Fell 2 meters away from me. Definitely scared the crap out of me

Zip file attached includes the DAT log file, TXT log file, and xlsx file converted from the TXT log file.

Thanks in advance for the community's help!
Posted by Hobby WOW | Today @ 04:46 AM | 68 Views
Unboxing of the SimToo Fairy Air from Hobbywow, One this
which did not mention in the video, is the drone has a built-in dvr recorder on the side of the drone. So you can use a 32gb sd card.

Simtoo Fairy Mini Foldable Brushless Quadcopter with Transmitter WifI FPV 1080P Camera Optical Flow Positioning GPS

Simtoo Fairy Mini Foldable Brushless Quadcopter (6 min 13 sec)

Posted by lawrence4 | Yesterday @ 10:08 PM | 193 Views
66% Vertigo on Float Maiden Flight (1 min 41 sec)

Wingspan 600mm
Weight 181g
Battery:2S 350mAh 35C. 4mins.
Motor:2204 1400KV,
Propeller:GWS EP-7035,
Servo:5g x 3,
Receiver: Frsky 4ch....Continue Reading
Posted by VicT | Yesterday @ 10:04 PM | 181 Views
I like to stop the prop while gliding especially if I use a folding prop. Here is a link to the ESC Instructions.
Posted by VicT | Yesterday @ 09:24 PM | 205 Views
I have many places where I fly RC and I have to carry the model and TX out to the runway or takeoff spot. For models like the high wing Apprentice, Valiant, Beaver, or Maule I use a retractable wire handle to lift and carry the model. The handle can be used to hang the model from a ceiling. The low wing Cirrus is different and so I use 65 b Spiderwire fishing line attached to the fuselage. I wrap the line with a clove hitch, put a drop of CA on the knot/toothpick and sink the tooth pick into the foam fuselage. When dry I test the pull strength of the string and joint. See...Continue Reading
Posted by JohnVH | Yesterday @ 04:52 PM | 333 Views
NEW Durafly Bonanza maiden and aerobatics!

Durafly Bonanza 950mm from Hobbyking FLYING! (5 min 31 sec)

Build video
Durafly Bonanza 950mm from Hobbyking Unboxing and Build (18 min 51 sec)
...Continue Reading
Posted by Jack Crossfire | Yesterday @ 03:59 PM | 310 Views
Can a PASSENGER land a PLANE? Presented by CAPTAIN JOE (15 min 51 sec)

After months of thinking about the problem, it became clear the passenger should fly manually instead of trying to reconfigure the autopilot as depicted. We're all familiar with the basic airplane controls, have played flight simulators, & can drive cars. Getting the plane to point in a certain heading & controlling speed isn't very hard.

The autopilot is a horribly complex addition. Most of the radio time is spent explaining how to use the autopilot & looking for the controls. She had to lower flaps, lower gear, & reverse thrust, despite the autolanding being engaged. A 2nd passenger could have managed the flaps & gear.
To the lay lion, manually flying would greatly increase the chances of success, but Caption Joe based the video on no doubt what the FAA recommends.
Posted by SPH1957 | Yesterday @ 02:53 PM | 348 Views
I thought I would document my experiences with my TarotRC equipment and the drones I fly.

Firstly this is what I have:

2 sets of ZYX-M
2 sets of ZYX OSD
2 sets of TL301 GoPro carrying gimbal
1 set of ZYX BD Bluetooth Data Link
Tarot 680 Ironman hecacopter
500 size quad

FrSky QX7
Fry sky receivers as follows.

Posted by blitzen | Yesterday @ 12:50 PM | 418 Views
I have improved my polystyrene foam cutter. The cost to build was about $10. Using household tools, a drill, soldering iron and glue gun it was complete in a couple of hours. The size accommodates polystyrene foam up to 1" thick. It is portable, powered by 2 alkaline D cell batteries. 3 inches of very thin steel wire is heated by resistance to just beyond the temperature polystyrene transitions. Polystyrene is safely cut in a ventilated area. The heat is minimized to avoid unhealthy fumes. As a result, cutting speed is more or less 9 inches per minute depending on the size and density of the PS. The cut is barely larger than the diameter of the resistance wire so detailed and accurately sized pieces and voids can be achieved. It also cuts thin molded PS (recycling symbol 6). The platform lifts off to change the batteries or resistance wire.
Resembling a pizza box, a 12" square frame made of 1.5" x .5" poplar with a .25" paper board top and bottom. The lumber was cut with a small hand saw. The top board is left unattached and small blocks are glued to the underside which keeps the top in position on the frame.
A light steel rod is bent at a right angle. One end of the rod is fitted into a hole in the frame and held with a set screw. The point of the screw tip is ground off. The arm is parallel to the surface at 2" above. The negative battery wire (24 AWG) is inconspicuously soldered to the rod using a heavy soldering iron. The resistance...Continue Reading
Posted by GroundControlRC | Yesterday @ 11:03 AM | 537 Views
RC Tip #18 - Bad Wiring Assemblies

Here is a link to the Video:

I have ordered power connector pigtails, extension cables, servo wires, etc. and approx. 25% of those have had bad wiring assemblies.
What I mean by bad wiring assemblies is the wires in the connector are not in the proper order.
I have had to remove wires from these connectors and re-install them in the proper order.
Never assume that the wire assemblies are correct and always check before you use them.
I installed a servo pigtail into one of my receivers and shorted out the receiver because the power lead was installed where the signal wire should have been.
I didn't check before I used the wire assemlby and it cost me a receiver.

Build, Fly, Crash, Repair, Rinse & Repeat!

Happy Flying!

See Us On Youtube | Patreon | RCGroups | Facebook
Posted by basslord1124 | Yesterday @ 09:20 AM | 582 Views
Been wanting to add a nice somewhat large glider to my airplane arsenal. Something for those lazy/relaxing days. Found some plans for a Flitetest style glider (called Galaxy) through the Flitetest community pages. Currently have the fuselage and tail section built. Next big step is the wing which I am actually going to make as a 2 piece wing with a split in the middle so I can take it apart for transporting. The original design was a full single piece wing that used 3 sheets of foamboard.

Here is a video on the start of this journey in constructing this big glider.

Large foamboard glider build progress & introduction... Flitetest style glider (Galaxy) (6 min 49 sec)

And here is the original Flitetest article on the glider:
Posted by alex111 | Yesterday @ 05:11 AM | 696 Views
Hi guys I'm building a model of kookaburra queen 2 long way to go but will get there some day
Posted by nigelsheffield | Yesterday @ 04:54 AM | 1,004 Views
Video to follow when weather is better and I get it tuned but already this is working better than betaflight 2s brushless whoop in terms of locked in flying, ( still needs more tuning for outdoors )silverware rocks!

I've already made some brushless silverware quads and some whoops but up till now never a silverware brushless whoop and having recently discovered 2s brushless whoops and the recent betafpv beta65x I decided it's time to build a silverware version a little bigger on the beta75x frame.

Parts used
Betafpv lite FC ( flashed with yets brushless silverware version )
Frame and props betafpv beta75x.
1103 10000kv racerstar motors. ( tracking affiliate link as motors were provided for review , no extra cost to you but they will let me have more stuff for review if people use this link )
ESC bs06d super s ( mention nigelsheffield123 for $5 credit )
Any 5v bec / ubec regulator ( got mine from AliExpress for about $1 )
Camera I will be using akk bs2 depending if I can find a spare one but anything will do as long as it's small and light is best.

To program the FC you will need an st-linker V2 and a free program ( I will provide a bin file once it's all setup nicely or those who don't want to go through setting up in Kiel )

Soldered wires to ESC and hot glue in place to stop them...Continue Reading
Posted by KiwiKid | Yesterday @ 02:48 AM | 741 Views
I have always been intrigued by the variety of flying wing and canard experimental aircraft ventures that were prevalent during and after WW2 in Britain. Some details of these are recorded in these two postings:

I am rather fond of "wing things": and thought it would be fun to knock up a flying wing in the form of the experimental ventures.

I chose the Scout Bee as a base, so at least I knew the aerodynamics should work. The winglets were made from 2mm corflute sandwiched between two bits of balsa with the flutes and the grain at 90 degrees to each other. A Windrider pod was used with a P-39 cockpit grafted on. Power is supplied by a 2200 3S battery. Covering is Solartex. The lower surface scheme was used on prototypes and experimental a/c to identify them to other pilots and to (hopefully) stop wartime gunners from taking pot shots at the strange shape in the sky.

The model has just been finished and I did the maiden today. Really pleased with how she flew - here's a vid.

Windrider Scout Bee (2 min 19 sec)

Posted by japim | Yesterday @ 02:15 AM | 750 Views
Again an excellent skills of my son - this time in the middle of R/C combat fight:

Racing Drone vs Aircombat (4 min 59 sec)

Posted by GBLynden | Oct 14, 2018 @ 11:44 PM | 783 Views
This is a 4S Lipo Power Flight with the new Durafly Supermarine Seafire MkIIB 1100mm WWII RC Warbird From HobbyKing.

HobbyKing Durafly Supermarine Seafire MkIIB 1100mm WWII RC Warbird 4S Lipo Power Flight (4 min 25 sec)

Here are my review notes for this Durafly Supermarine Spitfire variant:

- A cool concept version on a classic WWII Warbird with tons of scale accessories that comes with three different scheme options.
- It is a great size for easy transport and still large enough to have a bigger plane feel to it.
- Flies great on 3S or 4S 2200 lipo batteries
- Very good flight times
- Scale flaps
- Retracts with rubber tires
- Nice bright LED lights
- A solid 3 bladed prop
- Ball link servo connectors
- It is quick and easy to adjust the tailwheel with provided tool

- The stickers can be a little tricky to apply until you get the hang of it. After that, it is pretty easy.
- If you aren't familiar with now the servo connectors work, it can be a little confusing. After you get a feel for them, it seems second nature.

To learn more about the RC Plane, click here!
Posted by DMHIGHFLYER | Oct 14, 2018 @ 11:39 PM | 781 Views
Alittle weekend fun in the 182, has the stol kit installed but needs to be converted to a tail dragger. 🙂
Posted by VicT | Oct 14, 2018 @ 10:51 PM | 806 Views
Tyvek hinges work very well as they can be used with regular CA and most foam airframes. Applied like Monocote hinges (but with CA rather than an iron) they are very strong and they dont stretch. I try and use them on ailerons, flaps, elevator and rudder. Here I use them on the canopy and receiver belly door for the Cirrus.

Get a Postal or Fedex envelope that is Tyvek. Sand both sides with 100-220 grit paper lightl to rough up the surface for CA. Use an accelerator on one side either the foam or Tyvek. Cut Tyvek into 1/8 wide strips. When applying CA use a very small amount and press down using clear Monocote backing as CA will not stick to this type of plastic.

The Cirrus canopy has 4 magnets and a foam tongue. Over time the magnets will either lose their magnetism or fall away due to heat expansion and contraction compared to the glue. Lose a canopy in flight? Good luck getting a replacement! Using the existing magnets and a hinge with a clasp increases the reliabilty of the latching design. You will never forget your canopy at home and no more canopys flying off the table at the flying field.

Start by applying a simple two strip hinge for the servo belly door. See pics. Then move on to the more complicated
Canopy....Continue Reading