Posted by PittSpecial | Jun 23, 2019 @ 08:33 PM | 3,746 Views
Hi guys,

Without posting my specific Power System Setup all over again here, I have linked to the Post back almost one year ago over the review thread at:

https://www.rcgroups.com/forums/show...65&postcount=7

The only item that I can say today is the purchase of (Quantity 2) 3-Cell, 2600mAH 45C Discharge GENS ACE battery packs!
I got these from my GravesRC Hobby Store in Orlando, Florida.

It really woke UP my model with it's specific Power System and the wooden 11 X 6 propeller. I found the throttle nothing over one click above 1/2 (Half) throttle.

Yes, no fancy Video but, I am super happy and thankful that we have the best GravesRC in Orlando, Florida that STOCKs the best in SouthEast USA!
Posted by bee99 | Jun 23, 2019 @ 05:16 PM | 2,346 Views
2019 is not the same as it was in 1996, when i was building from plans. I got the frame built, but it came out crooked. So i got discouraged and stopped working on it. Back before ARF's, if you wanted to fly,you had to build. Well anyways yesterday i purchased a Tower Hobbies foam Hellcat.
Posted by BernardW | Jun 23, 2019 @ 03:54 PM | 2,666 Views
The mutant Stik-shaped model is coming along bit by bit as I can find the time. I've been using that build like a blog, for general model-related guff, and neglecting this page so I'll try to keep in mind what each is really meant for. What I wanted to post here is my good results with new tools, for me anyway, on that build. I made a little sanding jig like a bench hook with an extra base piece sticking out one side and that works as a track to slide a sanding bar along. The top piece of the jig is square to that edge so it's easy to sand a piece square. The sanding bar is made of 50 x 30mm rectangular aluminium extrusion with sandpaper spray glued to it, and a gap at the bottom to clear the base of the jig. It works great, especially for sanding the angles on the ends of the diagonal braces in the Warren truss rear fuselage sides. I mark the angle I want on each brace from the stringers then place it on the jig at roughly that angle, first to use it as a bench hook while I saw it then to sand it to fit. It works very well. I bought another 1 metre long piece of the same hollow bar as a long sander and it's also been very handy. I've got coarse 80 grit paper on one side and 180 on the other. So far I've used it mainly to true up the edges of full length balsa sheets for edge gluing, as I needed to join 3 sheets for each skin for the wing D-tubes. It gives a nice straight edge that's properly square to the face all the way along, which isn't guaranteed using a blade and...Continue Reading
Posted by maxfiaj | Jun 23, 2019 @ 03:04 PM | 2,260 Views
Hi, I just piled my sport model in today. The front end was quite badly damaged. I will dispose of the LIPO battery but wonder if I should scrap the motor too. Its a turnigy aerodrive. How can I tell if its wrecked? Is it ok to run it up again after bad crash? Thanks for any advice. Not found out what caused the crash yet. The model started to porpoise at speed and then would not respond to controls.
Posted by dragonman1967 | Jun 23, 2019 @ 12:12 PM | 2,296 Views
Hello can anyone tell me how rare are these airplanes?
Posted by whitehawk | Jun 23, 2019 @ 10:45 AM | 2,602 Views
Not including the multitude of micros....damn you Blissinindy!!
Posted by John Liacos | Jun 23, 2019 @ 08:14 AM | 2,446 Views
Does anyone know of a provider foe the qequired balsa materials for these types of kits/ I have a materials list.
Posted by FLOEY | Jun 23, 2019 @ 02:37 AM | 3,067 Views
Long time since I wrote anything in my blog. Some Years ago when I mainly flew propeller planes
I bought 4 kits from "Sonic Model" also sold as Hype in Europe. Recently I discovered that these planes
still was sold under the name Nicesky. Wingspan 680mm approx 26" so they are not park size models.

The 4 kits were: Hurricane, Focke Wulf 190, P-47 Thunderbolt and a P-51D Mustang.

The Hurricane went into the bin pretty early it was a awful flew like a dog, foam crappy it was simply junk

Then I assembled the FW-190 struggled a bit to get the COG correct but managed it. That one is just
brilliant it almost flies like a Focke Wulf FW-190 it's just amazing!

For some weeks ago I started to assemble the P-47, flew it today (early morning no wind) with a E-flite 9x4,7 prop.
The prop is a bit too big for the plane I will try an APC 8x4,7SF or similar later.

Update
Could not find any 8x4,7 in my stock pile so I went for APC 8x6SF and that made the day!
Need to increase rudder throw ...


Nicesky_P-47_680mm_wingspan (2 min 14 sec)

Posted by old4570 | Jun 23, 2019 @ 01:48 AM | 3,621 Views
WLtoys F959 bound to my Taranis Q x7 (5 min 52 sec)



It was a cold / foggy day today !
I think it was just around 10deg Celsius when I was at the park and the breeze was just picking up .

The WLtoys F959 has been around for a long time now .
It has earned a rep for being value for money , but I really hate the factory transmitter .
The one that came with my F959 simply confirmed my right to not like the Factory supplied transmitter .
So I simply bound the F959 to my Taranis Q x7 .
Since the F959 runs the old Flysky protocol , you could use a 9x or other transmitter that supports the protocol .

I had previously trimmed the F959 for glide , and the Q x7 simply makes controlling the F959 so much more rewarding .
So at the park under power the F959 was pulling up . I literally needed almost all the down trim the trim pot offered ( mine is set to fine ) .
But once trim was established , the F959 was so easy to fly . It is almost a hands off plane .
For most of the flight I was running about 30% throttle ? ( watch the video ) .

I have to say , I was flying the F959 a little slowly . It never tried to stall out on me , not even when I tried to lower the throttle even more . The F959 simply started to slowly descend .
I did do one full throttle pass and turn , then cutting the motor going into a glide . ( I lost altitude quickly because the glide trim and power trim are so different ) To glide you really need to gently apply a little up...Continue Reading
Posted by mlilasic | Jun 22, 2019 @ 05:47 PM | 4,575 Views
Review of HOBBYMATE ASTEROID 3" MINI FPV RACING DRONE (BNF or KIT)

Promotion of Free Shipping for all products on HobbyCool.com: *code: Freeshipping38*
The promotion will be good through November 20, 2019.

My new 3" quad from Hobbymate came and it looks super cool and quality build. I got BNF version, build is super clean and all solder joints are nicely done. Details are in picture gallery.




HOBBYMATE FPV carbon fiber racing drone is a 3-inch quad built to go fast with load of power. Equipped with SmartAudio, which means it’ll be easier for a pilot to change settings on the video transmitter.



Parameters:
  • Wheelbase: 145mm
  • Frame weight: 35g
  • Arm thickness: 4mm
  • Top plate thickness: 2mm
  • Flight control mounting holes size: 20*20mm
  • Supported Motor:13xx / 14xx / 15xx
  • Supported propeller: Max 3 inch
  • Weight wo props:




  • Weight w Gemfan 3035 props:

...Continue Reading
Posted by mlilasic | Jun 22, 2019 @ 05:17 PM | 4,505 Views
Review of Eachine E016F 3-in-1 EPP Flying Air Boat Land Driving Mode Detachable One Key Return RC Quadcopter RTF

New quad/car/boat toy came to me and its great fun







Description:
Brand Name: Eachine
Item NO.: E016F
Color: Black&Orange
Material: ABS, Hardware and Electronics
Frequency: 2.4G
Channel: 4CH
Quadcopter Battery: 3.7V 350mAh LiPo Battery (Included)
Flight Time: about 6 minutes
Charging Time: 40 minutes
Transmitter Mode: Mode 2 (Left Hand Throttle)
Transmitter Power: 2 x 1.5V AA Battery (NOT Included)
R/C Distance: About 50 meters
Quadcopter Size: 13 x 15 x 5cm
Package Size: 25.5 x 19.3 x 7.3cm



Features:
  • 3-in-1 Flight Mode, simple operation, free combination of aircraft and foam hull, to achieve a variety of play in sea, land and air, mode switching easy to use, not limited to the environment.
  • Air Flying Mode(Aircraft alone), Land Driving Mode, Surfing above Water Mode.
  • Detachable aircraft. The aircraft and the base can be split and freely combined.
  • The aircraft with the Base can slide on the ground and experience the perfect drift feeling of the remote control high-speed car.
  • The aircraft with the Base also can floating on the surface of the water, experience the remote control boat galloping water.
  • Headless Mode, the Aircraft no need to adjust the position of aircraft before flying .
  • One key to return function. The aircraft can automatically return to home point.
  • Automatic alarm and automatic landing function. When the
...Continue Reading
Posted by steve wenban | Jun 22, 2019 @ 04:57 PM | 4,061 Views
I'm currently working to restore a Cat to static display as well, its good to be working on aircraft again , so keeping myself rather busy in my retirement
Posted by steve wenban | Jun 22, 2019 @ 04:24 PM | 4,023 Views
Well with the other 2 models nearly ready for paint it was time to start my next scratch build PSS'er . The Fiat G-55 I started drawing up some time ago before the house move , I started yesterday and framed up nearly a full half fuse . Today should see it fully framed up . Plenty of colours to choose from on this aircraft as wel
Posted by RCvertt | Jun 22, 2019 @ 03:19 PM | 3,850 Views
Apollo XI flying field is open again! Max flight ceiling of 250 feet.

Previous limit used to be 400 feet. Lucky we got 250 though. Curious how the new height limit will affect the larger aircraft and especially turbine use.

***If you see a helicopter hovering, even way in the distance, LAND immediately. Don't go around again, LAND immediately.***
Posted by Bill M - RC | Jun 22, 2019 @ 11:01 AM | 4,301 Views
Hi fellow rc pilots & rc enthusiasts

NEW VISUO ZEN K1 Review Introduction – Brushless 5G WIFI FPV GPS with 4K HD Dual Camera Foldable RC Quadcopter Drone COMING SOON.

Finally a brushless quadcopter drone from Visuo

You can get this VISUO ZEN K1 Brushless 5G WIFI FPV GPS With 4K HD Dual Camera Foldable RC Quadcopter Drone RTF here now: http://bit.ly/2Y1RbbW

Visuo ZEN K1 review introduction - Brushless 5G WIFI FPV GPS with 4K HD Dual Camera (1 min 44 sec)

Posted by GroundControlRC | Jun 22, 2019 @ 09:44 AM | 3,574 Views
DustOff #8 - XK Edge Stunt Plane 3D Mode White Knuckle Flight ;-)



Here is a link to the Video:
https://www.youtube.com/watch?v=LdA6GFmik7k

Let's really blow the dust off this plane!
3D Mode will test your skills ;-)

Here are links to this plane and spare batteries:

Link to this Plane:

XK A430 2.4G 5CH 3D6G System Brushless RC Airplane Compatible Futaba RTF - Mode 2
https://www.banggood.com/XK-A430-2_4...47791920140372

Spare Batteries:

XK DHC-2 A600 RC Airplane Spare Parts 7.4V 300mAh 25C Li-po Battery
https://www.banggood.com/XK-DHC-2-A6...47791920140372

Turnigy nano-tech 300mAh 2S 35~70C Lipo
https://hobbyking.com/en_us/turnigy-...asc=5382684821

Link to the Motor Upgrade Tutorial:
https://www.youtube.com/watch?v=FbyYabReelU

Link to the Motor Upgrade Tutorial Photos:
https://www.youtube.com/watch?v=QySeWgj4QHM


See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

See Us On Youtube | Patreon | RCGroups | Facebook

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
https://www.facebook.com/pg/Ground-C...3132721/posts/
Posted by bill_delong | Jun 22, 2019 @ 09:20 AM | 4,175 Views
TheJANG from UltimateRC did a battery review many years ago using a discharge graph comparing 30A discharge cycles between MaxAmps brand and a couple budget brand packs that were available at the time. TheJANG found that performance was nearly identical between the packs and could not recommend MaxAmps with the opinion that they were over stating their C ratings and the price they were charging were not justified. MaxAmps would retaliate and forced YouTube to remove any video that TheJANG had published with MaxAmps in his content over "Copyright Protection". TheJANG had to cross out MaxAmps in any reference to his review on his website. He even banned the word MaxAmps from being used on the URC forums... folks would quickly adobt the name MaxCramps which was very accurate.



Posted by Tazkiller85 | Jun 22, 2019 @ 05:07 AM | 4,631 Views
Yep Les Amis,
Eachine 1, Fatshark ... au boulot !!! D'accord elles ne sont pas "parfaites", le DVR est très long à mettre en route et sa qualité n'est pas la meilleure du marché. D'accord la recherche automatique des canaux est aussi un peu longue (72 canaux 1 par 1 c'est relou ) . Mais mis à part ces petits défauts qui ne sont pas les qualités premières qu'on demande à des lunettes FPV, ces EV200D sont EXCEPTIONNELLES !!! Le FOV est parfait, l'image est magnifique, la réception excellente, le confort est top ... En toute honnêteté ces lunettes n'ont actuellement aucunes concurrente sérieuse dans cette gamme de prix. Proposées à 245€ aujourd'hui jusqu'au 23 juin, c'est sans aucun doute LE MEILLEUR RAPPORT QUALITÉ PRIX sur le marché des lunettes FPV ! Vivement les EV300D .. LOL . Merci de votre soutien et ... Bon Film à Tous .

Eachine EV200D Vs Fatshark - Review Test Démo - Pas parfaites mais presque ! (28 min 16 sec)


NOTATAZ : 18/20 Fatshark n'a qu'à bien se tenir !!!

Niveau : Débutants et Confirmés
Les + : Images, Ergonomie, Confort, Réception, PRIX !
Les - : DVR et recherche auto trop long ...

Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous si vous les utilisez pour passer commande si le produit vous intéresse :

- Eachine EV200D 245€ du 21 au 23 juin : http://bit.ly/2HqzUTP

- Accessoires EV200D : http://bit.ly/2X4NYfn
- Caddx Ratel (coupon BGFRcaddx530 ) 26.56€...Continue Reading
Posted by frank4wing | Jun 22, 2019 @ 01:16 AM | 4,194 Views
Someone lost his RC sailplane in the field and we did some search and rescue using the DJI Mavic. After that I had great fun chasing wings and planes in the golden hour. Buddy 10REDFPV made a nice cut of it along with some funny footage from his cinewhoop.

MFG | FRANK4WING | 10RED FPV (2 min 31 sec)