Posted by basslord1124 | Today @ 02:22 PM | 5 Views
After working through some of the kinks with the FT Simple Cub, I managed to add another kink by bending the prop shaft. I had actually never done that before. But I guess all that lawn darting can lead to it. I didn't even realize it had happened until I had done some repairs and was ready to fly it again.

FT Simple Cub... Bent motor/prop shaft? (2 min 2 sec)

Posted by slidewaysgts | Today @ 12:29 PM | 59 Views
Got this kit from sunset models as a shrank down version of the 120 kit. The stick sizes weren’t scaled down to standard size so 3/8 spruce was just too small for spars. 1cm carbon square used instead. Wing is SOLID so far.
Posted by Jantje66 | Today @ 08:22 AM | 164 Views
A while ago (2005) I build this catamaran with 2 Phoenix 125 speed controlers and 2 Graupner inline 700m 24v. brushless motors.
The first time I went sailing, the 2x 16 NiMh cells melted!
So i parked the boat and recently i dusted the thing and decided to try again.
I bought 2 LiPo 6s 22.2v 5400Mah and tried my luck... and failed. Again.
The double speedcontrolers where fried while testing the motors and setup.
Now i need two new speed controlers who can stand the heat, abuse and the current.
Can anyone give mee advice?
I would like to enjoy this boat and stop putting money in this project.

Trying an other hobby is not the answer i expect :-)
Posted by marblekit | Today @ 01:16 AM | 394 Views
Posted by wattechighland | Yesterday @ 11:03 PM | 454 Views
今回はFRPでWTCを作るつもりです。 WTC(water tight compartment)...not cylinder
Name: 01IMG_2716.jpg
Views: 0
Size: 87.8 KB
Name: 02IMG_2717.jpg
Views: 0
Size: 86.2 KB
マグネットを4か所仕込むところまで。当初8か所にするつもりでしたが、磁力が強いので4か所に減らしても 可かと。
...Continue Reading
Posted by DoubleEagle | Yesterday @ 08:38 PM | 514 Views
Item No.:E564-003
Model Name: 1:20 RC Mercedes-Benz Arocs Container Truck
Size of vehicle (cm): 60.6*16.1*21.7
Radio controlled: trailer split joints, trailer hight level control.
Speed: 10km/h
Remote distance: 20 meters;
Simulated Lights/Sounds (mute button)
Rechargeable battery and USB charging line included
For more products visit:
Business enquire: [email protected]
Double-Eagle Rc 1:20 Mercedes Container Truck Model toys (0 min 58 sec)

Posted by Bill M - RC | Yesterday @ 06:54 PM | 564 Views
Hi fellow rc pilots & rc enthusiasts

Makerfire Happymodel 3s 11 1v 300mah HV30 60C Lipo battery review. Suitable for power whoops like a HappyModel Mobula 7 HD, FullSpeed Tinyleader, 75mm Crazybee F4 Pro CineWhoop, URUAV UR85/UR85HK etc. I test performance & duration on a Fullspeed Tinyleader HD CineWhoop.

You can get these Makerfire Happymodel 3S 11.4V 300mah Lipo Batteries HV 30C/60C with XT30 connector in uk here:

You can get these Makerfire Happymodel 3S 11.4V 300mah Lipo Batteries HV 30C/60C with XT30 connector internationally here:

Makerfire Happymodel 3s 11 1v 300mah HV30-60C Lipo battery review (7 min 19 sec)

Posted by deenice57 | Yesterday @ 04:33 PM | 618 Views
My max 5 lost power have to turn it off and on the red light be blinking can someone help
Posted by unboxingexp | Yesterday @ 03:56 AM | 983 Views
Balancing DJI's Ronin-S (2 min 22 sec)

Posted by old4570 | Yesterday @ 12:28 AM | 1,079 Views
It occurred to me ...
That part of the problem lies with the way the pod is a attached to the boom .
3 screws holding it in place to a carbon plate ..
So a lot of force is applied to 3 very small places on launch ..

So before a problem arises , why not just epoxy the pod in place ?
Create a much larger area to distribute launch energy into !
Anyhow , that's what I have done with the Raven 990 ..
I fibreglass reinforced the pod , then glued it in ..
When the Epoxy dries , it should distribute load much more evenly over a much larger area .. ( + the fibreglass wont hurt too much - I hope )
That vertical fin is still weak as ! Next time it breaks , I will cut it out and rebuild it with more carbon reinforcing .
Posted by old4570 | May 18, 2019 @ 09:04 PM | 1,109 Views

I have issued a product alert : ( Well - for what ever it's worth )

I removed the pod from my Raven 990 and it has a stress fracture @ the same location as my Mini DLG pro ( where it broke )
Posted by GroundControlRC | May 18, 2019 @ 07:23 PM | 1,108 Views
Maiden Flight - MinimumRC F8F Rare Bear Pro

Here is a link to the Video:

This Plug-n-Play Kit is courtesy of Banggood.
I've been wanting to try out one of these Brushed Motor Nano/Micro Planes and wanted to review the Pro Version which is a 4 Channel Plane.
This is our Maiden Flight!
Here we go!

Here is a link to the Build Videos:

Part 1:
Part 2:
Part 3:
Part 4:

Here is a link to the Pro PNP Version of this Kit:

MinimumRC F8F RareBear Pro 360mm Wingspan 4CH KT Board RC Airplane With 8520 Coreless Motor KIT/PNP - PNP

Here is a link to the Standard Version Plus Motor & Servos of this Kit:

MinimumRC F8F Rare Bear 360mm Wingspan KT Board Mini RC Airplane KIT With 720 Coreless Motor - KIT+Motor+Servos

Here is a link to the Receiver I used:

2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC

Here is a link to the Servos:

TY Model 1.7g Servo With JST 1.0mm Plug Compatible Spektrum 6400 Series Receiver For RC Airplane

Here is a link to the Batteries I used:

5X Eachine E011 E011C JJRC H67 RC Quadcopter Spare Parts 3.7V 260MAH 30C Battery USB Charger Set

See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

See Us On Youtube | Patreon | RCGroups | Facebook