ron

Posted by Three-Wire | Today @ 06:54 PM | 395 Views
A-10 armament
Posted by kopterheld | Today @ 06:29 PM | 628 Views
The ExpressLRS 2G4 transmitter module ES24TX happy model up to 1000mW, fan, RGB LED and Moxon antenna. Super reception better than TBS Tracer. Range over 30km with 100mW and EP1 receiver.


Happymodel ES24TX Pro Version:
BG Code: PARTS8 - https://www.banggood.com/custlink/D3DhbGFmTA
AE - https://s.click.aliexpress.com/e/_AeLqQf

Happymodel ES24TX (250mW)
AE - https://s.click.aliexpress.com/e/_Arc4Yx
BG - https://www.banggood.com/custlink/G3GhLFYp81

Video (EN subtitle) -
HappyModel ES24TX Pro 1000mW ExpressLRS 2,4GHz Modul (3 min 55 sec)


Starter Set ES24TX
AE - https://s.click.aliexpress.com/e/_ANT9cB

Moxon Antenna
AE - https://s.click.aliexpress.com/e/_A1BSGL

Cooling Fan
AE - https://s.click.aliexpress.com/e/_Ag931F

BetaFPV ELRS TX Module
Code: KOPTERHELD21BF - https://bit.ly/BFELRS24G



Inside a thick aluminum heat sink with fan

...Continue Reading
Posted by rickp | Today @ 05:24 PM | 1,188 Views
Was gifted a partially built CHT Albatross by a generous friend of mine, so thought I'd document the build and maiden.
The fuselage was mostly complete, with the exception of final placement of electronics, servos and pushrods.
The aileron wing was assembled, but lacking servos and pushrods. The polyhedral wing was unassembled.
Posted by PittSpecial | Yesterday @ 09:33 PM | 6,129 Views
Okay,
As I type this tonight, there has been many USA distributors that have discontinued the Dynam line of RC EPP Jets that operate on 3, 4-cells with great results. It is my thoughts that it is perhaps the bigger picture to get more profit margin by the introduction of the larger and heavier EDF jets. These newer EDF jets require 6-Cells and capacities now range into the 5,000mAH (5.0 Amp-Hour) Lithium Polymers.

Hence, my beloved and discontinued "White" Dynam Turbo Twin 64mm EDF Jet that operates with just a 3-Cell, 2200mAH, 35C, Lithium Polymer still is operational today and I was lucky to find a true gentleman who sold me some hard to find parts for my Dynam Turbo Jet. (Picture attached).

A few have contacted me saying to provide a video showing the performance and most importantly the landing of this very nicely designed EDF Jet by Dynam so, here it is:

Dynam Turbo Jet 64mm EDF at Moon Port Edited 10 28 2014 (3 min 44 sec)

Posted by Old_Pilot | Yesterday @ 06:13 PM | 6,884 Views
Das Ugly Glider - Part 3

Very productive day...and very pleased with the weight...got the fuse assembled and dry fit the tail section...I'll be darned if it doesn't look like a little Ugly Stik...The Tab-A-into-Slot-B method made the assembly so easy...I guess I'll start on the wing tomorrow
Posted by Merovech | Yesterday @ 11:39 AM | 7,938 Views
Hope everyone had a great week. Our family met at Grandmother's house in Arkansas, she has a 10 acre field which was very nice for flying in. Wish I had brought more planes!


Posted by Tazkiller85 | Yesterday @ 06:05 AM | 9,086 Views
🧐Yep Les Amis,
Mais Kcec ? Bacta ! Lol. Voici enfin l'explication de la petite vido publie sur le groupe LES TAZOUX il y a quelques jours. Mais en premire partie de vido, je tenais vous montrer mon nouveau kit de tournevis de prcision et surtout, vous faire profiter de l'offre actuelle ! ... Prenez soin de vous (et des autres) et merci tous pour votre soutien .


Un prototype à pas cher ! Et le JIMI JM - GNT80, le TOP pour l'atelier et le terrain !!! (20 min 48 sec)


🧐NOTATAZ : 19/20 Mon kit de tournevis Prfr !!!

- JIMI JM - GNT80 ( 30 avec le coupon BG309445 ) : https://www.banggood.com/custlink/3G3hbRRag0
- Train d'atterrissage ( coupon Parts8) : https://www.banggood.com/custlink/3GDENERjgq
- Kit de vis M2 : https://www.banggood.com/custlink/GGDYbdYOQZ
- Kit de vis M2/M2.5/M3 : https://www.banggood.com/custlink/mvDYndhaso
- Gilet chauffant : https://www.banggood.com/custlink/mGvhAdhoAm

😋Pour TOUS LES BONS PLANS, RENDEZ-VOUS dans le :
- TABLEAU DES PROMOS ET COUPONS 2021 RC et ACCESSOIRES (remis jour quotidiennement, en utilisant ces liens, vous aidez la chane, ) : https://docs.google.com/spreadsheets...it?usp=sharing
😋 Tableau provisoire pour le BLACK FRIDAY : https://docs.google.com/spreadsheets...it?usp=sharing

- Si Vous voulez aider la chane avec un don (tous les dons servent alimenter les vidos en produits ou matriel ): https://streamlabs.com/Tazkiller85

Pr...Continue Reading
Posted by Jack Crossfire | Yesterday @ 02:07 AM | 9,867 Views
The left motor went to valhalla while slinging the DSLR 10 miles. Thus another day went to rewinding a motor with 20 turns of 26 AWG. The PETG motor mounts are taking the heat nicely, letting motor after motor fry. The retaining ring was documented to show future lion it was properly reinstalled. Those retaining ring pliers have proven essential.


Some notes during the replacement were crash damage to the bottom panel. The 1.6mm tread tire still delaminated. The next step would be 250C printing, but delamination doesn't seem to have any impact unless it picks up a branch.
Posted by BlRDMAN | Yesterday @ 01:38 AM | 9,967 Views
Piggy backing fets has been done by many. Link shows XP-3A as an example.

https://www.hacksmods.com/2012/04/ho...brushless-esc/

Pic is one I did for Genius CP around 2012 2014. Most recently did a MX-3A.
Posted by BlRDMAN | Yesterday @ 01:28 AM | 9,996 Views
I believe this feature of the MX-3A ESC is unknown to most. This esc in its stock form is programmed to accept pwm input of 1kHz, 2kHz, 4kHz and 8kHz with a simple modification. Simply add R1 and R2 resistors (form a voltage divider), value is 1K, size is 0402. This size resistor is "small" but can be done with most ordinary iron with a sharp tip. I have soldered many components this size with a dirty old 40W Weller soldering iron.

Hint, find any copper rod, rivet or similar of correct diameter to fit your iron and sharpen to a point, round point ever so slightly. Clean and tin as it heats up.

Cheers
Posted by Casheon30 | Nov 26, 2021 @ 09:54 PM | 10,588 Views
After being discontinued, I got lucky and feiboa still had the molds to build me my favorite jet of all time. This is the actual jet, I got lucky a second time when they also had a pair of retracts still available....Continue Reading
Posted by BDOG1 | Nov 26, 2021 @ 08:56 PM | 10,774 Views
Thanksgiving week here in the north east and for the second week in a row I was able to "double dip " and get in 2 flying sessions in one week

Tuesday started with a couple of inches of fresh snow and a forecast of 15 mph winds and 36 degrees - Perfect to get a old flying buddy who had moved down south and was back in town for the holidays out for some fresh air....and get some stick time on a good combat wing {His current slope plane is a Goldberg Electra }.
I downloaded the Knife Edge model from my radio to his and out we went,I knew it would be a good day,my buddy the red tail hawk circled us as we walked up the hill .
The wind at the top was less than predicted and vectoring ,not the greatest conditions especially for a newbie ...
I launched and trimmed the wing , flew around scouting the lift and showing him how to search and cruise.
These Knife Edge wings are very efficient , if allowed to run they will slice thru sink and climb in even the lightest choppy lift that we often have on our hill as the wind vectors around.
I handed him the transmitter and coached him for a bit,after a couple of minutes he was doing well by himself so I asked if he was good with me putting my plane in the air,he said yes so I jogged back to our gear and grabbed my plane hoping he would still be in the air when I launched .
No problem - he was doing fine and enjoyed the game of hide and seek as the lift ebbed and flowed around and out in front of the hill .
After about...Continue Reading
Posted by Normanshouse | Nov 26, 2021 @ 05:30 PM | 11,489 Views
In search of a great planes super skybolt kit, new in box, unopened preferable, if opened all parts must be accounted for. Shipping insured and double boxed
Posted by Old_Pilot | Nov 26, 2021 @ 04:25 PM | 11,833 Views
There's an airplane in there somewhere..I swear it is..now I just have to figure out where all these parts go.....LOL
Posted by Old_Pilot | Nov 26, 2021 @ 01:38 PM | 12,532 Views
I cut all the parts this morning, and starting to assemble. Wing ribs are 1/8", Fuse sides are 1/8", Fuse top,bottom, stab and fin are 3/16, as are the ailerons, wing tips and TE
Posted by PittSpecial | Nov 25, 2021 @ 11:17 PM | 16,812 Views
Guys,

Just could not wait any longer for parts so, what did I do?

I went to work on my beloved Turbo Jet and fixed as best I can the Frontal Fuse area using 1850 Watt hair dryer, White Glue, and Spackle by 3M.

Hair Dryer took out the largest dent on the nose and white glue placed the two halves of the FUSE back aligned and even.

Also, replaced the Nose Retract, wheel and it steers like new!

I could not believe how well the Jet flew this morning!

Zoomed like a home sick dove!

EDIT: That bump on the frontal nose was there when I purchased it from someone in Central Florida and you can see the For Sale Ad here:
https://www.rcgroups.com/forums/show...LPU-Tampa-Area
Posted by GBLynden | Nov 25, 2021 @ 04:26 PM | 18,091 Views
This is the E-flite UMX Night Vapor doing some High Alpha & Other Fun!

E-flite UMX Night Vapor High Alpha & Other Fun! (2 min 59 sec)