Posted by lawrence4 | Mar 03, 2020 @ 09:53 PM | 7,019 Views
Fiu Push Motor Installed (0 min 36 sec)


Motor: C1404 3000KV 9g
Propeller: EP-5030
ESC: TURNIGY PLUSH-6A
Posted by old4570 | Mar 03, 2020 @ 07:55 PM | 5,977 Views
Stuffed up the cam again !
I charged the battery last night , and it was another instance where the cam did not turn off after pulling the USB cable ( Which it should do )
So this morning the battery was flat . ( I think I need to check the battery every time I pick this cam up now )

PNP > Yes the Super Cub is plug an play now ! No more stability .

How did it fly ?

It was nose heavy , I am going to have to re-check the CG . The Cub has been nose heavy from day one .
I went up and the Cub was hunting the ground , so I landed and flipped the CUB . ( Those wheels are too small )

I moved the battery further back .. Went up and now it flew very close to the money .
Flying relatively fast ( more than 50% throttle ) and the cub does cut a fine line . Butt's !!! , I like to fly slow !
Dropping the throttle to 40% or maybe 35% the cub began to squirm a little . Did a little jimmy , with the wings just twitching forward one way then the other . Maybe like a car driving on ice . Kind of made me think I was close to stall . And to be honest it was not that slow , I have other models ( Lighter obviously ) that fly much slower .
Rolls > Not enough aileron ! I jammed in about 75% throttle and the roll was so slow I could only complete about 75% of the roll and then I had to pull out ! ( Of the roll ) It was a nerve racking roll cos it was so slow .

Landings , I jammed it into the ground 3 times because !
The cub seems to...Continue Reading
Posted by CorvetteC5 | Mar 03, 2020 @ 02:47 PM | 7,008 Views
This is a special build, for it is a tribute to my dad who passed in 2015. Within the first couple of years after his death, I restored his two Zagi 400x wings to flying order and find it a treat to channel his flying through them These nearly 20 year old wings endured my antics until summer of 2019, when the patriotic red-white-blue one crashed itself in a near vertical nose dive, after the ESC/BEC shut off during a high speed pass, through mature corn stalks onto the dry clay soil. The right half of the foam wing shattered under the tape finish, the center plastic battery holder fractured and hinged forward, and the twin fins sheared away.

All this damage could be repaired, of course, but not without loosing the original finish work from dad. Which is annoying to me. Instead, his Zagi 400x RWB wing is presently in retirement, and my search for a similar wing yet assembled using modern design techniques is finished. Among the abundance of prefabricated, and kit, wing designs that I researched, the models from Crash Test Hobby stand out. Cut from EPP rubberized foam, in a one density for the wing, and a heavier density for the control surfaces, I was drawn to their use of string (shock cord) and 3 mil laminate reinforcements. Plus the RC gear is embedded into the foam for protection, streamlining, and simplicity. All new technique that peaked my interest.

From the abundant choice of wing sizes and shapes from CTH, I selected the Rebel S14 because of its...Continue Reading
Posted by kramer | Mar 03, 2020 @ 12:34 PM | 6,488 Views
I don't get out to the flats by Woodruff AZ too often but when I do I enjoy the company of like minds. EL Falcone and Buddy are usually there.
Posted by DutchRC | Mar 03, 2020 @ 12:08 PM | 6,519 Views
Halloa people,

I am in the midst of publishing a (LONG :P) how-to-build series and one of it's video is partly about the video-transmitter choice.. Maybe this is helpfull to you if you're new to FPV and are unsure what camera would work out for You...
Also in this video however I explain how to install the VTX & configure it in Betaflight

The VTX I'll end up using: Rush Tank Ultimate PLUS - 800mW

Perfect FPV Drone Build Guide - P9: Video Transmitter Install & BetaFlight (27 min 55 sec)

Posted by GroundControlRC | Mar 03, 2020 @ 09:51 AM | 6,231 Views


DustOff #4 - Volantex Super Cub V765 - Great Flying Super Cub with Plenty of Power ;-)

Here is a link to the Video:
https://www.youtube.com/watch?v=a9G7Jwocy64

I don't have a lot of time with this Plane but I'm getting more comfortable with it every time I take it out.
I'm a bit rusty on the landings as it's been a while since I've flown this Super Cub.
This Plane is fairly Aerobatic and has plenty of power to pull through large loops ;-)
Let's get it in the Air!

Banggood GCRC
https://www.banggood.com/custlink/GmDmQ1nVkO

Here is a link to the Playlist for this Plane:
https://www.youtube.com/playlist?lis...vfLZBBBUK-P9Z6

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #Volantex #SuperCub #V765

You Can Help Support Us By Using Our Affiliate Link To The Product Below. A small commission (At No Cost To You) helps us buy more items to review.

Here is a link to the Plane:

Volantex Super Cub
https://www.banggood.com/custlink/DKGKkDUkZ0

Here are links to the LIPOs I use:
***Note I converted the Connectors on the ESC and LIPOs to XT30 Connector on mine. I do not remember the type of connector that is stock.

Turnigy nano-tech 450mAh 3S 65C Lipo
https://hobbyking.com/en_us/turnigy-...asc=5312339847

Here is a link to the 7x4 Prop I use with a Spinner Collet:

JXF Poly Composite Propeller 7x4 (2pcs)
https://hobbyking.com/en_us/jxf-poly...asc=8256570960


See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Ground Control RC™ Glue & Fly™ Series Scratch-Build Planes

Consider Supporting Our Channel by becoming a Patron at: https://www.patreon.com/groundcontrolrc
Patrons of the Channel will have Exclusive access to Aircraft Plans & Content!

See Us On Youtube | Patreon | RCGroups

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
Posted by Gimbal Guy | Mar 03, 2020 @ 07:58 AM | 5,666 Views
Whenever spotting and or submerged in fpv, I always try to find the best time pieces to time my flights and or have a built in alarm to let me know when I should be landing; just in case there is some malfunction with a buzzer or telemetry data... (which is rare or never but just in case )
BLUE ANGELS PERPETUAL CALENDAR ECO WORLD CHRONO SKYHAWK AT8020 (4 min 36 sec)

#fpv #timer #theurbangentry #chronograph #pilotwatch
Posted by lawrence4 | Mar 03, 2020 @ 03:37 AM | 6,384 Views
Fiu install Motor Power Test 1 (0 min 37 sec)


Wingspan: 740mm
Length: 360mm
Motor: Q1612-3000KV 7.4V 4.6A 165g/output weight:10.8g propeller:5030 ESC:6A
ESC: Xstar XP-7A
Battery: 2S
Receiver: Frsky D4R-II
Propeller: GWS EP-4040,4530,5030.
Servo: 2
Posted by CKD315 | Mar 03, 2020 @ 03:08 AM | 5,856 Views
I've been wanting to get a jet for years now but didn't want to go with one of those rtf foam planes that most folks start with.

I had read a lot about my options and found out the F-16 was a good first jet for a lot of folks back in the day. So when I found this one at the Perry swap meet last week I couldn't pass it up. I bought it as a bare airframe, and I'm starting the search for an edf motor/fan. I'm not sure if I want to go with an original "byrofan" setup or go with some carbon fiber setup from this century.

It's been worked on and appears to have been reinforced with cloth and has servos mounted in the wing. It also has a flying stab configuration, and a fixed rudder. It's been sitting on the intake and fins for a while now and has a few cracks that are mostly minor.

It seems I never get a plane fully finished and detailed until after I've flown it for a while, so I'm not going to worry about its appearance for now. I'm really looking forward to getting it flying and finding out about all that hoopla with jets...
Posted by wish4vette | Mar 02, 2020 @ 09:01 PM | 6,407 Views
Acro practice!!!
Posted by Cox PT-19 | Mar 02, 2020 @ 07:44 PM | 6,863 Views
So, the "Engine Sniper" moves stealthily through the tall grass of internet anonymity, eyeing his Ebay target in the manner of a mountain lion stalking a fawn, with his PayPal locked and loaded as the time ticks down.

Cold-blooded, he has little compassion for his fellow model airplane nerds that he KNOWS are lusting after the same treasure...for THEY are JUST as cold and unfeeling...and deserve no mercy.

In a low whisper that barely crosses the darkened room, the Engine Sniper's utterance is more breath than spoken word,
"Not today, my friends...not today..."

With a few moments to spare, he allows himself to recall his victory of the previous evening, when he snapped an Ohlssen & Rice .049 from the midst of a group of week-long competing bidders...
With a sum so massive, it was akin to aiming a cannon at a hamster, he'd waited 'till the last 5 seconds to unleash the Fury of "Auto Bid". He then punched the "B" button.

His fellow nerd bidders were scattered like so many hyenas forsaking fresh carrion to a pride of hungry lions.

The surge of electronic money swamped and exhausted all other efforts, and then shut itself down after claiming it's prize with only a few dollars above the previously highest bidder. Before the dust had settled, it's seller had received payment, and the Engine Sniper once again disappeared into the internet marsh.

Now, the target is a fairly nice Anderson Royal Spitfire 065. From the 1950'...Continue Reading
Posted by kopterheld | Mar 02, 2020 @ 04:07 PM | 6,654 Views

Reptile CLOUD-149 is a 3 inch Mega CineWhoop. For less money you can get a solid quad for cinematic video filming with e.g. a GoPro camera.
Get the Reptile CLOUD-149 from [CZ] EU warehouse with the coupon: aFfBg10 - https://www.banggood.com/custlink/3Dvvl7sWcf
Coupon2: BGRE149

Video 1 - Reptile Cloud 149 CineWhoop good and less $130 (EN subtitles)
Reptile Cloud 149 CineWhoop gut und günstig (4 min 36 sec)


The PNP 3 inch CyneWhoop has 20A ESC's, F4 FC, 1407 4000KV motors, 25-500mW VTX video transmitter.


...Continue Reading
Posted by Cancerfighter1 | Mar 02, 2020 @ 02:54 PM | 5,391 Views
Hey guys this is Ricardo I found a way to slow down my retracts on my flyzone F4U Corsair anybody is having the same problem I found a product that works exceptionally well for this model it was described to me as a Servo speed control module it's basically a wire with a male end and a female end with electronics in the middle which light up when installed in the receiver with female end to Servo wire you will also need a y wire to complete . got mine online from Hobby Unlimited part # vhb-ac-5777 good luck . try it only 4 bucks
Posted by pdooley | Mar 02, 2020 @ 02:29 PM | 5,906 Views
namely, the bms-661dmg+hs

i provided feedback in this thread, been using these in ground vehicles for years, no servo saver and some pretty decent bashing. no failures to speak of other than broke the ears off one, but that was a full speed hit into a stationary object, hit hard enough to rip the a-arm off and break the center out of the wheel. that servo still works fine, just the case has no ears for mounting.

well yesterday another one failed. car started steering sluggish and then complete failure. the servo arm locked in place. i took it apart to find motor and probably board too was burned. gearset was fine but motor completely locked.
i did notice what looked like corrosion on the motor can, probably from water getting around the oring seals(not very good seals i noticed).

either way, the servo went for many hours before giving up. who knows how much longer it would last if kept dry. I have 3 others in service so will keep evaluating.
also will take the unbroken case from this dead one and fix the other, put it back in service.
Posted by Lieutenant Dan | Mar 02, 2020 @ 01:55 PM | 5,407 Views
Well people, I have sold just about every thing I have posted on RCG's classified pages. and I thank the buyers and I thank RCG for that. but, I have only had 2 people reply on my feedback page. so, if you buy something from anyone please remember to leave feedback, specially if the deal wen't well. thank you!!


3/19/2020.
I sold a giant scale plane about 3 weeks ago. I sold the plane for a lost of about $190 in investings. the buyer did not leave feedback for me.

3/19/2020.
so people, it happened again. I sold a 44cc engine and the buyer receive the engine 1 week ago from today,
it's been a week he has had it and the buyer did not leave feed back for me and he did not PM me telling me he receive the engine.
I waited 1 week to post this.
Posted by Old_Pilot | Mar 02, 2020 @ 10:03 AM | 6,802 Views
Last toy for a while...thermoplastic vacuum table.....a bit of 1/2" and 1/4" ply, a cheap hot plate, and my shop vac..
Posted by GonzoBorinquen | Mar 02, 2020 @ 09:46 AM | 5,495 Views
Heinkel 162 Salamander WWII turbine model. It took me seven months to build the model. The kit was produced by Bruce Sanders Century Jet Models. The kit is no longer in production. The kit is a very complete short kit. All wood except wing planking is included. Main kit parts are a fiberglass fuselage with plywood bulkheads and foam core wings.
Have not given the Salamander its maiden flight yet even thou I has been ready to fly for a while. Will publish how it went with the maiden flight when it takes place. April 2020 is the set date for the maiden flight.

The design of the full scale HE 162 took four months and 1st prototype was shortly available after that. The plane went thru a very short trial period with many retrofits installed after almost every test flight. Been in production in late 1944 and with many materials in short supply, the creation of the 1st squadron itself was a major task.

The model is controlled by a Futaba 9C radio, powered by Jet Central Rabbit 100 SP, Century Jets retracts, Xicoy sequencer to coordinate landing gear with gear doors and Jettronics variable low-loss braking system. Controlled by 11 servos. Controlled by Futaba are two servos in Ailerons, two servos in Flaps mixed with elevator switchable, one servo on each Elevator, one servo on each rudder, two servos controlled by the Xicoy sequencer for air valves ne for retracts another for gear doors and one servo for steering.

Fuel load is 124 oz. distributed by in four tanks in...Continue Reading
Posted by J.Enders | Mar 02, 2020 @ 07:05 AM | 5,491 Views
On my Taranis X9D, I took the long left switch to switch the motor labeled SF, but the switch is on the right side of the simulator. I attached a picture with red letters as it should look like.Can someone confirm it for me.
According to the switch assignment, the order should be as red in the picture.
Sorry for my bad english, I hope you will understand what i mean.

best regards from Germany