Posted by BDOG1 | Yesterday @ 07:15 PM | 557 Views
I had some solartex {sky blue} but had never used it before.
I know that it is highly prized and the slope guys love it so I thought I would give it a try and see if I could cover the epp canopy on my DAW P-51 with it in just one piece .
Posted by old4570 | Yesterday @ 05:52 PM | 660 Views
MG800 round two (12 min 0 sec)


This was originally supposed to be sub 250 , and it was ! Butt .....

The CG was too far back ( 70mm ) and the ESC was faulty , cutting the motor as soon as you went over 3A current draw .

This flight C of G was around 60mm and the battery was a Nanotech 1000mAh 2s ..
Flying weight from MEM was around 268 grams .
New ESC is a 10A Turnigy ..

It has taken a long , long time to get back to this model . I think I can forget about Sub 250 with this one .
The CG would most likely want to come forward a little , maybe start around 50mm from the LE for more stability .
Roll axis stability still bites , and trying to fly straight and level is a little challenging .
The MG800 wants to roll left or right when trying to fly straight . I may need to pull out some expo for faster response time to help tame the roll .
@ 60mm CG , the elevator is still sensitive , I am still @ 100% rates . So maybe lowering the rates to 80% and jacking up the expo a little ?

Flight time with the 1000 mAh battery was around 15 minutes @ 50% throttle , cell voltage was 3.79v when I got home . I ended the flight when I noticed some battery sag ( power sag ) .
Posted by santanig5 | Yesterday @ 04:57 PM | 703 Views
https://www.motionrc.com/products/fl...-ix-1600mm-pnp

https://www.rcgroups.com/forums/show...Spitfire-Mk-IX

Scale Fidelity:
* 92% Scale Outline, 94% Scale Contours
* Scale suspension struts, pre-installed on all PNP aircraft
* Scale four spoke wheel, plastic, with brass axle shaft
* Scale four panel split flaps, plastic, with ribbing detail
* Scale canopy contours
* Cockpit floor and wall area is designed to accommodate a near-full depth cockpit tub, for you customizers/detailers out there
* Big 16" Prop
* LED wingtip lights
* Pre-installed dorsal signal light. Can be plugged into the circuit board to flash intermittently, but because the real Spitfire only used this light to flash Morse Code to communicate.

Durability:
* Soft tires, slightly oversized, for operation on rough surfaces
* Grass capable landing gear with thick steel pin and metal trunion
* Digital Metal Gear servos on all control surfaces
* Brass Ball Links on all control surfaces
* Nylon hinges on all control surfaces
* Plastic cowl
* Machine Screw Inserts molded into the spinner backplate for easy adjustment of the blades' tracking while mounted on the motor
* COOL: Plywood ribs and carbon spars sandwiched in a hollow chambered wing. Strong, light, rigid.

Transportability and Usability:
* Removable Wings (Wing halves are screwed together, then screwed to fuselage)
* Removable Cannon Barrels
* Removable Antenna Mast
* Removable chin scoop (the part most prone to frontal...Continue Reading
Posted by RC Roundtable | Yesterday @ 04:47 PM | 715 Views
Episode 101: "Good Night and Good Luck" is now live!
http://rcroundtable.com/podcasts/mp3...pisode_101.mp3

In this episode, we went live to talk about:
-Lee's Twin Otter flight report (1:25)
-Fitz's Beaver story (9:00)
-FAA updates (23:00)
-Fitz's new models (42:15)
-OSMW Mambo updates (52:20)
-E-flite Air Tractor (1:13:00)
-E-flite UMX Turbo Timber (1:22:10)

You can visit our website at RCRoundtable.com to listen over the web or download an MP3 of the show. Or, you can subscribe to RC Roundtable on iTunes.
We would love to read your comments and ideas. Please drop us a line here, on twitter, or via email: [email protected].

You can visit our website at RCRoundtable.com to listen over the web or download an MP3 of the show. Or, you can subscribe to RC Roundtable on iTunes.

We would love to read your comments and ideas. Please drop us an email: [email protected].
Posted by DTD_2112 | Yesterday @ 03:28 PM | 760 Views
I think my last entry was the rickety old bridge. We calibrated the climb and realized it was 55į steep incline at the top of the bridge which is almost difficult to climb. However we both have crawled our trucks over it. We will be expanding the area where we crawl. I am currently building a teeter totter to put in the middle of our course and my brother feels that we need to work on the water feature. He wants a waterfall. I have a circulating pump so we will have something put together by summer. My brothers RGT took on some damage he broke an axle and we waited for the parts to come in. He was operating in 3 wheel drive for a while. He is now back to 4 wheel drive. I have been thinking about getting into 3D printing. I want to make accessories for my truck. Iíll let you know what I decide to get in the next couple of weeks. Our 3rd crawler the WL 10428 is out of commission we blew out the plastic gears in the steering servo. I have the servo on order but we are also thinking of getting a build kit and maybe making a truck out of the WL parts while waiting on the parts from that country that takes forever to send things out. I just really want to get that green buggy back on the track. For now Iíll leave a few photos. I have a climb video coming soon. For now enjoy whatís left of winter itís starting to warm up on the East Coast.
Posted by DutchRC | Yesterday @ 12:01 PM | 1,017 Views
Halloa

so you might have seen video's from / about the new Runcam 5 Orange pass by.. I thought it would be informative to demonstrate One of it's new features. Not only to show how well the Runcam 5 does in flat colors, but also to show you why you might want to use it..

Link to the camera: Runcam 5 Orange

at Banggood: Runcam 5 Orange


So.. a short video showing what "flat color profile" is.. and how you CAN use it..
I shot this video in horrible weather, because is especially hard on camera's..

Runcam 5 Orange - Flat Color Style - Flight Demo (10 min 1 sec)

Posted by GonzoBorinquen | Yesterday @ 11:32 AM | 1,040 Views
My 1st turbine plane....what a way to start.

In 2014, a friend of mine gave me a Joe Saitta ME 163B that had been handed down thru many hands since 1999. The model had never been started, it was a propeller driven, 82", ME 163B short kit. It still had the original plans, Fiberglass fuselage and some of the ribs and bulkheads. The rest had been lost thru time.

I contacted Joe Saitta thru email. He was very supportive and indicated that things had changed since 1999, now his model was turbine powered. The fuselage was the same as well as the wings, but the bulkheads and other items in the fuselage guts had changed. He prepared an upgrade kit for me and I was ready to start.

I had been building models for some decades, so this was not an issue. Turbines was another thing, I had no knowledge of them. Nor was I AMA turbine certified. A good friend of mine, Juan Garcia, became my mentor and taught me all I had to know on this power plants and models.

I finished the model in a few months. Since this plane lands on a skid, landing gear is detached on takeoff. I prepared an aluminum skid that follows the external contour of the fuselage. This will protect the belly of the plane upon landing in grass field. The landing gear/dolly was made of wood and aluminum and version 1.5 was the perfect one which I have been using the past five years. The first four versions had each a different flaw which required modification. Takeoff dolly release can be very tough on the...Continue Reading
Posted by OBXGyrene | Yesterday @ 11:08 AM | 1,086 Views
I just completed my second plane, an E-flite Valiant, 1300mm. The kit was nice and easy to assemble. Although I am partial to scale aircraft, I chose this plane for use as a trainer due to its forgiving nature and ability to fly a slower speeds.


I made a few cosmetic changes by removing all the ugly decals and replacing them with a custom set I made and had printed on water-slide decal paper. I limited these decals to just registration numbers, a few indicating the type (Valiant 480E--since that is how it is listed in the instruction manual), and some blue and silver striping on the wheel pants. I also painted the propeller tips in white. By removing the decals on the blue colored surfaces quite a bit of paint was pulled off. To remedy this I used some matte acrylic Apple Barrel Cobalt-Hue paint to cover the bare surface, and then sealed it with clear satin water-based Polycrylic Minwax. I came out to a perfect match and is very difficult to tell from the original finish!


I also purchased a set of floats for this plane which I am in the process of modifying by adding a set of water rudders and a waterproof steering servo.
Posted by GroundControlRC | Yesterday @ 08:14 AM | 1,170 Views


DustOff #10 - XK A430 Edge Stunt Plane - The Last Flight of the Edge!

Here is a link to the Video:
https://www.youtube.com/watch?v=3zf67MGd-rA

I took the XK Edge Stunt Plane out for it's Last Flight.
This is a very nice flying Stunt Plane with some unfortunate durability issues.

Complete Playlist for the XK Edge Stunt Plane
https://www.youtube.com/playlist?lis...XUUjKJ7PRyE9qC

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #XKEdge #StuntPlane #A430

You Can Help Support Us By Using Our Affiliate Link To The Product Below. A small commission (At No Cost To You) helps us buy more items to review.

Here are links to this plane and spare batteries:

Link to this Plane:

XK A430 2.4G 5CH 3D6G System Brushless RC Airplane Compatible Futaba RTF - Mode 2
https://www.banggood.com/XK-A430-2_4...47791920140372

Spare Batteries:

XK DHC-2 A600 RC Airplane Spare Parts 7.4V 300mAh 25C Li-po Battery
https://www.banggood.com/XK-DHC-2-A6...47791920140372

Turnigy nano-tech 300mAh 2S 35~70C Lipo
https://hobbyking.com/en_us/turnigy-...asc=5382684821

Link to the Motor Upgrade Tutorial:
https://www.youtube.com/watch?v=FbyYabReelU

Link to the Motor Upgrade Tutorial Photos:
https://www.youtube.com/watch?v=QySeWgj4QHM


See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Ground Control RCô Glue & Flyô Series Scratch-Build Planes

Consider Supporting Our Channel by becoming a Patron at: https://www.patreon.com/groundcontrolrc
Patrons of the Channel will have access to the latest Aircraft Plans & Exclusive Content!

See Us On Youtube | Patreon | RCGroups

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
Posted by chris cahill | Yesterday @ 02:10 AM | 1,614 Views
Can anyone tell me were i can buy a pss glass fuse for a around 30 -40 inch wing span war birds like a me109 or Mustang etc or kit
Posted by OBXGyrene | Yesterday @ 02:03 AM | 1,638 Views
I'm new to the world of radio control aviation. I've been wanting to get into this hobby since I was a kid the 1970s, however due to the cost, raising a family, and my duties a a Marine, I had to put it off. With the advent of the age of low-cost computer technology and the use of foam for model kits, RC aviation is now both affordable and much easier than it was in the past.


In October, I purchased and built my first model, and E-flite PT-17. Actually, since it has Navy markings it is technically an N2S. I was really impressed with this kit, and with the assistance of Monofoil Man, I was able to detail the aircraft with authentic decals, rigging, and many other scale details. I also joined the AMA and our local flying club, the Dare County RC Flyers.

Posted by marblekit | Yesterday @ 12:25 AM | 1,639 Views
Posted by marblekit | Feb 17, 2020 @ 11:58 PM | 1,736 Views
Posted by marblekit | Feb 17, 2020 @ 09:37 PM | 1,919 Views