Posted by ShonanBeachRC | Today @ 11:39 AM | 685 Views
In my last video my ZD-Racing Thunder ZMT-10 (10427 - S / 9106) lost the will to move So I have partially taken it apart! In this video a little update and possible upgrades I can do to make the ZD-Racing Thunder ZMT-10 (10427 - S / 9106) more suitable for the beach! If you have any ideas let me know in the comments!

If you like to buy the ZD-Racing Thunder ZMT-10 (10427 - S / 9106) :
https://www.banggood.com/custlink/vvDycOQQfN

Please visit my website! https://www.shonanbeachrc.com/
Twitter: https://twitter.com/beach_rc
Minds: https://www.minds.com/shonanbeachrc/
Parler: https://parler.com/profile/ShonanBeachRC/posts

#rccars #banggood

ZD-Racing Thunder ZMT-10 (10427 - S / 9106) Rebuild! Update and planned Upgrades! Part 1 (2 min 37 sec)

Posted by Cox PT-19 | Today @ 10:54 AM | 867 Views
So, we pulled it off!

Once again, Larry McKenzie's brain child---"Black Fly Day" took place on Breezy Hill!

Lots of sunshine, but with cold wind and turbulence breaking over Breezy Hill. Still, that didn't stop the Flyers from using the WHOLE day on "Black Fly Day".

Our one "casualty" was Billy's new Piper Cub which either had a radio problem, or got caught in one of the many rotors that were rolling across the field.

The Control Liners stood their ground in the wind, and it seemed that the Flite Streaks and Shoestrings...and one lonely Bi-Slob...kept on flying when not taking breaks to allow the R/C's to take a turn. At this point, the Crop Circle is intersected by the R/C runway, but plans are underway to move it toward the east a bit to give everybody some elbow room.

I had my Sig Kadet Senior Sport out among the Electron Herders, making sure the R/C runway got a good dose of castor oil. Stan Fronabarger's stunt-flapped Flite Streak "Big Bunny" got some flying time, though we're gonna have to try it again when the wind is calmer.

Special Guest, Allen Bagg, drove the 60 miles or so from down south with his collection of Flite Streaks, and had a big time smoking the Crop Circle.

Flyer Brian had his Control Line Shoestring, whose aft CG gave him some considerable entertainment in the rough air.

A great time, and full day, as confirmed this morning by my aching feet and stiff back!

Still more great stuff to come....Continue Reading
Posted by ShonanBeachRC | Today @ 09:54 AM | 948 Views
I went to the beach again with my ZD-Racing Thunder (ZMT-10 / 10427 - S / 9106) on 3S lipo, this time to conquer the great wall of sand! In the end I broke it, guess the electronics are not that waterproof! I really like the ZD-Racing Thunder ZMT-10 / 10427 - S / 9106! I think it's a good beginners car cheap, quite fast and strong!

If you like it buy it here:
https://www.banggood.com/custlink/vvDycOQQfN

Please visit my website! https://www.shonanbeachrc.com/
Twitter: https://twitter.com/beach_rc
Minds: https://www.minds.com/shonanbeachrc/
Parler: https://parler.com/profile/ShonanBeachRC/posts

#rccars #banggood

ZD-Racing ZMT-10 / 10427 - S / 9106 VS. The great wall of sand on 3S lipo (can he make it?) (6 min 26 sec)

Posted by ShonanBeachRC | Today @ 09:11 AM | 1,139 Views
Out of the box I really do like the HBX Protector (12815)! This is my second HBX and both of them are above expectation! They are reasonable cheap and amazingly strong! So far I only broke the servo arm after I hit a wall. It’s not the fastest car, but it’s also not needed that much I guess. BUT…. I like a bit more power, so I’m upgrading it with an brush-less motor. I’m using an 2845 3930KV Sensor-less Brushless Motor with an 35A ESC. I think this is the maximum motor size that fits. The servo is not a standard size servo, it’s a bit smaller. Therefor i used the Feiyue FY-S3 2.8KG Servo which has metal gears!

HBX Protector (12815) Buy it here!
https://www.banggood.com/custlink/GmKhJsQric
or here!
https://s.click.aliexpress.com/e/_d72EIYF

Feiyue FY-S3 Servo Buy it here!
https://www.banggood.com/custlink/m3vYJAArPt

2845 motor Buy it here!
https://www.banggood.com/custlink/Gv3ycsQCVg
or Here!
https://s.click.aliexpress.com/e/_dWT9TBz

Please visit my website! https://www.shonanbeachrc.com/
Twitter: https://twitter.com/beach_rc
Minds: https://www.minds.com/shonanbeachrc/
Parler: https://parler.com/profile/ShonanBeachRC/posts

#rccars

HBX Protector (12815) Brushless Upgrade on 2S lipo! (4 min 9 sec)

Posted by ShonanBeachRC | Today @ 08:31 AM | 1,215 Views
I personally really like rc kits! That’s why I bought this HSP 94111(Brontosaurus) kit! I bought it already quite some time ago but never used it after assembly. These HSP kits are quite cheap, about 80~90 dollars. Except for the motor, ESC, Servo, body and battery everything is included in the kit. In this video a small impression of the HSP 94111 because the ESC kept quitting!

I personally enjoyed assembling it, so if you like it, Buy it here!
HSP 94111 kit https://s.click.aliexpress.com/e/_9wyAmW
or if you want a RTR buy it HERE!
https://s.click.aliexpress.com/e/_A9fRIE

3650 Motor and ESC!
http://s.click.aliexpress.com/e/_dWKKgfF
https://www.banggood.com/custlink/333mTyNafQ

Please visit my website! https://www.shonanbeachrc.com/
Twitter: https://twitter.com/beach_rc
Minds: https://www.minds.com/shonanbeachrc/
Parler: https://parler.com/profile/ShonanBeachRC/posts

#rccars

HSP 94111 (Brontosaurus) RC Kit Any Good? (3 min 44 sec)

Posted by Hilson87 | Today @ 08:07 AM | 1,219 Views
It’s no secret that I’m a huge fan of extreme flights release of the Turbo Raven. I think they got all the dimensions and construction on this release dead on! The one minor disagreement is on the power setup, they recommend 6s and I have to say that for me and my thumbs it’s more of an 8s ship. I originally had set my very first one up per the manual and felt that i was having to use the high end of the throttle way to much throughout the flight to fly high alpha and most of the low and slow stuff. It just felt like it was on the cusp of being underpowered and the power system being overworked. So after my first raven met it untimely demise 8 flights in to owning it i decided to go for 8 cell and a slightly larger motor
on the new one. WOW! was my expression when i got to flying my current 2nd Raven! It now seems perfect! Just the right amount of over powering! Now i can fly mostly at just over half the entire flight of my high alpha maneuvers and the plane still has tremendous amounts of thrust and throttle in reserve for those holy shoot moments! Which for me happens all too often lol.

So the setup I’ve decided on is as follows:

Motor- Dualsky GA2000 (Stock they call for the GA1500)

ESC- Hobbywing 120 Fly Fun V5

Prop- I go back and fourth on this depending on what type of flying i mostly intend to do that day.
So its between a Falcon CF V2 Comp 17x8 Wide and a Foxtech Supreme CF 18X6.5 (quad prop). I had done some experimenting and found this Foxtech prop...Continue Reading
Posted by Tazkiller85 | Today @ 06:06 AM | 1,632 Views
Yep Les Amis,
WAOUH !!! Reçu depuis seulement quelques jours, je n'ai pas pu attendre plus longtemps pour tester le nouveau WIND5 LITE de HGLRC ! La conception et les matériaux du châssis lui confère une excellente résistance aux chocs pour un poids mini, son électronique est performant et fiable (Zeus, Eolus, Foxeer), et sa puissance INDENIABLE ! Bravo HGLRC pour cette évolution du WIND5. Les seuls petits reproches que je pourrais faire c'est que la sangle me parait peut être un peu légère pour une telle puissance, on aurait aimé du Kevlar, et le VTX qui ne développe que 350mW ne sera certainement pas assez efficace sur de longues distances mais largement suffisant dans les 500m.
Sinon, vous l'aurez compris, ce petit monstre de puissance a tout pour plaire aux amateurs de sensations fortes en 6S et ravira les débutants en 3 et 4S par sa fiabilité et sa résistance aux crashs ! ... Bon Film et merci à tous pour votre soutien .

HGLRC Wind5 Lite - Review Test Démo - Un petit Monstre de PUISSANCE ! (39 min 29 sec)


NOTATAZ : 19/20 Un TOP !!!

Les + : Léger, Très résistant, Bonne autonomie, Caméra Excellente, VTX efficace, Grosse puissance Très compact ...
Les - : VTX seulement 350mW max (mais efficace), Une sangle Kevlar aurait été judicieux ...

Présentation/unboxing : 00:15
Vol à vue : 12:06
Vol FPV 4S : 15:06
Vol FPV 5S : 21:24
Vol FPV 6S : 27:05
Conclusion : 31:59
Mon Bétaflight : 38:45

Chez HGLRC :
- HGLRC Wind5 Lite (Predator 5) : ...Continue Reading
Posted by Jack Crossfire | Today @ 04:43 AM | 1,772 Views
Pretty disappointing RPM's with the large 70 turn motors. Built up a new board to allow direct control of all the enable pins, which got it up to 272rpm on 10V. It would need 35V to hit the required speed with no load, 40V for margin. The next step would be reducing the turns to 20 & increasing the current.

Trying the motors with a sensorless ESC got them up to a slightly faster RPM but much less torque. Standard ESC's can barely get them started on 12V but use the current a lot more efficiently. The size of the motor drastically increased the required voltage for a given number of turns by virtue of the resistance.

Over the years, lions have avoided cleaning flux whenever possible. It's manely necessary for adjustable regulators. It otherwise might improve water resistance.
Posted by PittSpecial | Yesterday @ 10:30 PM | 3,629 Views
UPDATE: RE: Carl Goldberg Tiger-2 (Glow-To-Electric Conversion)

Earlier Post on same subject at:
https://www.rcgroups.com/forums/show...Electric-Part2

Well, I finally got it right!

As some that have posted warned me, this heavy model just could not fly "or" in other words, I have to thank a higher power for giving me the common sense of NOT horsing this great looking model UP in the air with the weak AXi 2826/10 power system and just 3-Cells! That maiden attempt resulted in some slow speed taxi runs!

Replaced the Electric Power System to the SUPPO 3520/6 (840Kv) and swinging the APC 12 X 8 E propeller while using the 4-Cells, 4,000mAH, 35C, Lithium Polymer Batteries.

I must declare that I was very pleasantly surprised in the manner this model handles itself up in the air. That Long FUSE Boom really allows this model to perform some wicked aerobatics should you decide at the controls. This made it worth while after struggling in trying to get the model's Center-Of-Gravity close to where it needed to be. Again, this model in it's early life flew with the Thunder Tiger .46 Glow Engine and it tipped the digital scale at over 16 ounces. This made things pretty challenging as there was really not enough selections of a Motor with this weight and having respectable (KV) parameters (Revaluations per Volt) to keep the Cell count low.

I decided NOT to remove the Impact Socket underneath the bottom end of the FUSE (Frontal) as it allowed a very good mid-point Center of Gravity with the new power system at 11+ ounces (Including ESC). It is amazing how much weight was required up front to balance this model out. I would say this Carl Goldberg Tiger-2 is very well constructed to say the least.

Okay, here's the Video and if you like to see a LOW Fast Pass then, FAST FORWARD to 6:25 Time Hack! Make sure you select High Resolution !
Carl Goldberg Tiger2 Maiden Flight 11 27 2020 (8 min 30 sec)

Posted by jmxp69 | Yesterday @ 06:32 PM | 2,549 Views
FPVWRA Racing Wing Maiden Flight with GPS Top Speed Recorded!
FPVWRA Racing • Defiant Spec Wing Maiden Flight • PLUS GPS Speed Recorded (15 min 4 sec)

Posted by Akram07 | Yesterday @ 05:13 PM | 2,612 Views
Selling this radio with 2 receivers one has 3 axes gyro. Like new only 4 flights. Has charger and original box.
Asking 170.00 buyer pays shipping.
Posted by Late99 | Yesterday @ 05:08 PM | 2,612 Views
I had noted a long time ago that Arm1s Extra seemed to be easy build and at least on paper looked as a good flier. As I had sold my 38" Skywing Edge last winter I was short of smaller plane to fly on the nearby farm field (using asphalt walkway as runway there). And as weather get worse and worse, I decided to build a replacement from all the parts I had laying around.

I'm still waiting for the maiden, so can't comment yet on the flight performance, but the build was quite fun & rewarding. Check full 1m MiniExtra story!
Posted by GroundControlRC | Yesterday @ 04:21 PM | 2,642 Views


Volantex Sport Cub 500 RTF w/Gyro - Aileron Extension Test Flights, My Quest for a better Roll Rate!

Volantex Sport Cub 500
https://www.banggood.com/custlink/DmGmUiY16o

Banggood GCRC
https://www.banggood.com/custlink/GmDmQ1nVkO

Here is a link to the Video:
https://www.youtube.com/watch?v=h0YKErAzswA

Even in Manual Mode the Roll Rate is a bit Slow!
I added Aileron Extensions to try and get a better Roll Rate.
It worked great on the Eachine Mini F4U Corsair, will it work on this Plane?

You Can Help Support Us By Using Our Affiliate Link To The Product Below. A small commission (At No Cost To You) helps us buy more items to review.

Volantex Sport Cub 500
https://www.banggood.com/custlink/DmGmUiY16o

EXHobby / Volantex
https://www.exhobby.com/us/products/...=5e824f89734c4

Here is a link to the Playlist for the Volantex Sport cub 500:
https://www.youtube.com/playlist?lis...khCQwKy5do3Bs8

Spare Parts: ***These Parts are for the Eachine Mini P51D Mustang but I believe they are compatible.

Lipo Battery 1S 360mAh for Eachine Mini Mustang P-51D RC Airplane
https://www.banggood.com/3_7V-360mAh...47791920140372

Eachine 3.7V 380mah 25C Lipo **I use these in the Eachine Mini P51D Mustang with no problem
https://www.banggood.com/Eachine-3_7...47791920140372

JJRC H31 RC Quadcopter Spare Parts Battery 3.7V 400mah
https://www.banggood.com/JJRC-H31-RC...47791920140372

JJRC H31 RC Quadcopter Spare Parts 6Pcs 3.7V 400MAH 30C Battery and...Continue Reading
Posted by ShonanBeachRC | Yesterday @ 12:21 PM | 1,236 Views
I really like these Crazy Tamiya DF-02 chassis. I'm surprised how strong they are! nothing has broken yet. It's really dry here in Japan now so i did some sand burnouts Tamiya Rising Storm DF-02 lol.

The upgrade made it quite fast. Will do a speed run soon!

3650 Motor and ESC!
http://s.click.aliexpress.com/e/_dWKKgfF
https://www.banggood.com/custlink/333mTyNafQ

Please visit my website! https://www.shonanbeachrc.com/
Twitter: https://twitter.com/beach_rc
Minds: https://www.minds.com/shonanbeachrc/
Parler: https://parler.com/profile/ShonanBeachRC/posts

#rccars

Tamiya Rising Storm DF-02 Crazy Sand Burnout! lol (6 min 7 sec)

Posted by ShonanBeachRC | Yesterday @ 12:01 PM | 1,237 Views
Finally I went to the beach, only a 2 min cycle, with the ZD-Racing thunder ZMT-10 / 10427 - S / 9106.
It was a bit windy so sorry for the wind noise now and then!
I really like the ZD-Racing Thunder ZMT-10 / 10427 - S / 9106! I think it's a good beginners car. It's cheap, quite fast and strong!

If you like it buy it here:
https://www.banggood.com/custlink/vvDycOQQfN

Please visit my website! https://www.shonanbeachrc.com/
Twitter: https://twitter.com/beach_rc
Minds: https://www.minds.com/shonanbeachrc/
Parler: https://parler.com/profile/ShonanBeachRC/posts

#rccars #banggood

ZD-Racing ZMT-10 / 10427 - S / 9106, 2S Lipo Finally on Shonan Beach! (4 min 46 sec)

Posted by unboxingexp | Yesterday @ 12:00 PM | 3,102 Views
Platube LED whoop gates (1 min 48 sec)

Actually, these are LED dog collars :-) But I use them as cheap LED gates for some tiny whoop indoor action!
Posted by ShonanBeachRC | Yesterday @ 11:51 AM | 1,237 Views
Hi, everyone. This is the brushless upgrade i did for my HBX Hailstorm (18858). It's my first video, so it's a bit awkward but i hope it's still useful.

Please visit my website! https://www.shonanbeachrc.com/
Twitter: https://twitter.com/beach_rc
Minds: https://www.minds.com/shonanbeachrc/
Parler: https://parler.com/profile/ShonanBeachRC/posts

HBX HAILSTORM:
http://s.click.aliexpress.com/e/dz7JgWEU

SERVO:
GOTECK GS-9025MG 9g MG90 Metal Gear Servo:
http://s.click.aliexpress.com/e/qokdFigs
-------
MOTOR:
RC 2435 KV4800/4500/3300 4P Sensorless Brushless Motor with 25A Brushless ESC for 1/16 1/18 RC Car Off Road Truck
http://s.click.aliexpress.com/e/EJGYKv9Q

Hobbywing QuicRun WP-16BL30 Brushless Speed Controller 30A RC Car ESC + 2435 4500kv motor+ programe card
http://s.click.aliexpress.com/e/4yADwuwk

https://www.banggood.com/custlink/DmGvnIGkkV

SHOCKS: (make sure you get 4 of the same length)
Hydraulic Metal Front Rear Shock:
http://s.click.aliexpress.com/e/tETWhnLw

DRIVE SHAFT:
HBX 18858 1886 18857 Drive Shaft Metal:
http://s.click.aliexpress.com/e/2i2oo52C

TRANSMITTER + RECEIVER:
https://www.banggood.com/custlink/GKK3nImTKc

HBX Hailstorm (18858) Brushless upgrade 54km/h (4 min 48 sec)

Posted by Eric Zhu | Yesterday @ 05:43 AM | 3,512 Views
DON'T MISS IT !!! AGFRC SERVO AMAZON BLACK FRIDAY & CYBER MONDAY, 20%-25% OFF DISCOUNT!!! Activity Has Started!!!

Event Preview: Amazon Black Friday and Cyber ​​Monday
Discount: 20-25% OFF
Location: Amazon US Store - AGFrc
Activity Time: NOV 27, 2020 0:00 - NOV 30, 2020 23:59

Name: 1.jpg
Views: 0
Size: 611.8 KB
Description:

Activity has started, which of these 7 products do you like best?

1.AGFRC SA86BVMW 12V 66KG programmable brushless smart servo + AGF-SPV2 servo programmer + 25T metal servo horn, Total: 25% OFF Discount.
URL: https://amzn.to/37ddEZ4

2.AGFRC A65BHL 33KG low profile programmable brushless servo + AGF-SPV2 servo programmer + 25T metal servo horn, Total: 20% OFF Discount.
URL: https://amzn.to/3q5lWef

3.AGFRC A81BHMW 45KG programmable brushless servo + AGF-SPV2 servo programmer + 25T metal servo horn, Total: 20% OFF Discount.
URL: https://amzn.to/33j5ZYp

4. AGFRC A86BHM 55KG programmable brushless servo + AGF-SPV2 servo programmer + 25T metal servo horn, Total: 20% OFF Discount.
URL: https://amzn.to/3l564op

5. AGFRC A86BHM(Red) 55KG programmable brushless servo + AGF-SPV2 servo programmer + 25T metal servo horn, Total: 20% OFF Discount.
URL: https://amzn.to/3l8W8dI

6. AGFRC A86BHM(Purple) 55KG programmable brushless servo + AGF-SPV2 servo programmer + 25T metal servo horn, Total: 20% OFF Discount.
URL: https://amzn.to/39hAiT2

7. ARX-482R receiver compatitable with sanwa FH3/FH4T FHSS Mode, Total: 20% OFF Discount.
URL: https://amzn.to/39iW2xY

Note:...Continue Reading
Posted by gquiring | Nov 26, 2020 @ 11:55 PM | 3,667 Views
I needed a case for my RadioMaster TX16S, this case is ideal for any standard size TX.

Husky transmitter case for RadioMaster TX16S, great deal for $20 bucks (14 min 11 sec)

Posted by HGLRC Company | Nov 26, 2020 @ 11:45 PM | 3,671 Views
https://www.hglrc.com/collections/bfcm
Name: blackfriday.jpg
Views: 0
Size: 579.8 KB
Description:

*You can get a free spare frame for any drones you purchase.

*Buy 4 motors and get one extra for free

*For orders over $119,you get free shipping + knitted cap + 4* LEDs

*For orders over $199, you get free shipping + knitted cap + Zeus Nano VTX + LR antenna