Posted by mojowoykin | Jul 25, 2021 @ 09:28 PM | 13,033 Views
Continuum V5 joined wing canard glider V5 maiden flight with Mike Frandsen piloting (6 min 2 sec)


At Torrey Pines Fun Fly 2021...

Continuum V5 joined wing canard glider V5 maiden flight with Mike Frandsen piloting

Q-"Continuum V.5" Maiden Flight with Mike Frandsen.

The Q- "Continuum" V.5 High Performance Joined-Wing Canard Slope Glider, as flown by Mike Frandsen.

Mike being interested in the "front-wheel drive" characteristics, stability, and response, seen here putting the glider to the test.

Featuring a laid up Kevlar-Carbon fiber-fiberglass fuselage from a mold of a 3d printed plug based on the original basswood plug.

New modified, bagged main and canard wings, with Kevlar living-hinges for control surfaces. 3D printed wing joiners, canard mount , and wing inserts of carbon infused PETG. Carbon tube wing rods and premium 3D printed PETG canopy, and "endlets", as we call them.

The Original Q- "Continuum"- V.5 High Performance Joined-Wing Canard Slope Glider maiden video.

There's nothing like having a premier pilot taking a design to it's limits.
Thanks Mike...
Posted by mechmove | Jul 25, 2021 @ 09:16 PM | 11,931 Views
Well, I had to try; after resetting my CG to 75mm I found an older prop with a 3 x 4mm set screw. I installed it, although it protrudes, it works. The correct size is 3 x 3mm. New set screws arrive tomorrow. The weight penalty is +4 grams, flying weight 539 grams. Made the drive out to Long Beach, flying much better now, in fact this is best handling airplane I have ever flown, hands down. Fly's straight and level, fast or slow, and maintains a good pitch attitude, I've only seen this in other peoples' planes.

Now the weight reduction task begins. Since I paid for the RTF ship, I believe there is only so much I should put into this effort. But I should at least eliminate the tail weight which at a minimum involves installing a smaller ESC. Need to get specs on the motor first.

It also needs to be noted, the 3mm set screw holding the motor shaft was a bit looser when I returned home. This tells me a pre-flight check of this screw is needed before every flying session. Climbing with less power is an option as is Loctite.
Posted by GBLynden | Jul 25, 2021 @ 07:09 PM | 13,566 Views
I recorded Tim last night flying his E-flite UMX Turbo Timber. This is the first real world test with my brand new Rode Wireless Go audio setup, so I will be tuning it slightly from here if it seemed too loud. Let me know what you think guys!

Tim's E-flite UMX Turbo Timber RC Plane Flight (6 min 44 sec)

Posted by gabrielisrael | Jul 25, 2021 @ 04:36 PM | 12,012 Views
Kiber model out of Moldova literally hand makes fiberglass combat planes, and I purchased one after watching the Petroncic Brothers on YouTube review it.

It has 1140mm / 44in wingspan, and put in a E-Flite Power 32, 80amp Turnigy ESC, APC 9x9e prop, HiTec HS 81 servo for the elevator, and Turnigy mico servos in the wings.

I am using a 4s 3300mah battery, and getting about 5-5:30 min flight time at mostly full throttle, with a top speed of 85-90 mph.

You can run a 10x6 prop, which makes it easier to hand launch, but you loose some top speed.

I needed to modify (enlarge) the motor mount area, and shim the motor (down and to the right), and add some balsa to attach the ESC, but it is a really great flyer!...Continue Reading
Posted by mojowoykin | Jul 25, 2021 @ 01:18 PM | 12,304 Views
Q-"Continuum V.3" DSS (Dynamic Slope Soaring)with Mike Frandsen... (5 min 20 sec)




The Q- "Continuum"- V.3 High Performance Joined-Wing Canard Slope Glider, as flown by Mike Frandsen.

Mike being interested in the "front-wheel drive" characteristics, stability, and response, seen here putting the glider to the test.

Featuring a laid up Kevlar-Carbon fiber-fiberglass fuselage from the original basswood plug.

Modified, bagged main and canard wings, with Kevlar living-hinges for control surfaces.

Currently flight testing The Q- "Continuum"- V.5 High Performance Joined-Wing Canard Slope Glider with video of the maiden coming soon.

There's nothing like having a premier pilot taking a design to it's limits.

Thanks Mike...

California Slopes are the Best in the West, with more video content from the West coming.

Check out http://www.majesticrc.us/ and see what the USA can produce...an advanced composite, carbon fiber pitcheron (twisty) "Jester" designed by Mike Frandsen.

""Follow the Light" and "Huck it"
OH YEAH,,,
"F L Y F A S T"
Posted by mechmove | Jul 25, 2021 @ 09:54 AM | 12,543 Views
Yesterday, as I was flying my Alpha, I tried to initiate another climb, but the spinning prop wasn't providing any usable thrust. So thinking the battery might be low, I landed ASAP. I had flown only 4 minutes, so it was unusual. I thought something was loose in the motor, but didn't know what. So I packed it away and enjoyed some time in the park since its a pretty long drive.

When I came home, I realized there was a 3mm set screw that was stripped, which held the motor shaft in place. Since this is the first time I've ever owned a Outrunner motor, I didn't even know this should have been a part of the pre-flight inspection! When I looked closely at the screw and the mounting receptacle, there were obvious metal shavings, so much so in fact the new OD was 2.5mm! To confirm, I was successfully able to fit a 3mm x 9mm bolt into the receptacle to confirm a solid fit. I was concerned about the need to re tap to the next higher size, if this is even possible, or worse case a motor replacement.

So I ordered a bunch of small metric set screws on Amazon Prime, ETA tomorrow. In the meanwhile, I plan on moving the CG aft from 72mm to 75mm. I feel its too nose heavy to slow down enough for thermal flight.

I may or may not go into Long Beach today, its a long drive.
Posted by Mad_angler1 | Jul 25, 2021 @ 04:44 AM | 14,654 Views

Runcam MIPI Camera
Taking a look at the Runcam MIPI Camera for the DJI Digital FPV System.

RUNCAM MIPI - A DJI FPV COMPATIBLE CAMERA YOU CAN ACTUALLY BUY (13 min 8 sec)

Posted by Bill M - RC | Jul 25, 2021 @ 04:07 AM | 12,843 Views
Hi fellow rc pilots & rc enthusiasts

SJRC F11 4K Pro review. In this SJRC F11 4K Pro review, I share unboxing, features, functions, app, calibrations, camera, fpv range, RTH & flight duration of this great value GPS drone with a 4K camera mounted on a 2-axis gimbal.

You can get this SJRC F11 4K Pro 5G WIFI FPV GPS With 4K HD Camera 2-Axis Electronic Stabilization Gimbal Brushless Foldable RC Drone Quadcopter RTF here: https://bit.ly/3rxWHCt

SJRC F11 4K Pro review - Overview & Basic Functions (Part 1) (33 min 11 sec)

Posted by GBLynden | Jul 24, 2021 @ 06:08 PM | 15,752 Views
This was my first official night flight caught on camera with my E-flite Night Radian RC Glider. I uploaded this originally on my GBLynden's RC channel, but decided to re-upload this less edited version in honor the rerelease to my Random Reviews channel.

Night Flight - E-flite Night Radian 2.0m Bind-N-Fly Basic RC Glider (5 min 46 sec)

Posted by JureZ | Jul 24, 2021 @ 02:56 PM | 15,909 Views
Extra 300 by HookLL - gift of a local friend, after some serious crash.

Some TLC brought it back to flying condition.

1200 mm wingspan, 1333 g AUW.

Original motor. Battery 3S 2200 mAh LiPo.

Folding prop.

Cowl made from Blue-Bunny Ice cream container. No landing gear ( belly lander) . No canopy.

Extra 300 by HookLL - Movie (2 min 42 sec)

Posted by Reckless_fpv | Jul 24, 2021 @ 02:47 PM | 14,995 Views
freestylin' (4 min 53 sec)

Posted by bebel25a | Jul 24, 2021 @ 11:44 AM | 14,695 Views
Bixler setup for FPV

Eagletree Vector, XT-60, with V2 GPS
Sunnysky V2216-12, 900 kv motor
E-flite 60 amp ESC with disarm switch
Smallparts CNC adjustable motor mount
Runcam Eagle camera
500 mw 1.3 gHz video transmitter with tuned inverted V antenna
Dragonlink control receiver V2 and antenna on wing
USB extension for Vector mounted for easy programming
Buzzer for locating plane if...Continue Reading
Posted by mechmove | Jul 24, 2021 @ 08:47 AM | 13,818 Views
This morning I got up very early to look up installed component model names that are installed in my Supra. My receiver an R6008 HS, and wing servos JR DS 368 are all 6 volt capable.

Also, the shock of my life, as I was in my garage sorting through all the boxes, there was one box behind my transmitter that was marked “car accessories“. Inside this cardboard box cassette tape accessories, a car drink holder from the 1980s, and some other stuff. Since it’s close to my RC gear I always open it to look for something. This morning I was looking for my receipt that would contain the itemized receipt of all radio components installed in my Supra back in 2009. (That information is actually contained in a post here) The receipt was not there, but underneath was some plastic. I turn the box over and to my surprise my Supra canopy was taped to the bottom! I couldn’t believe it. Blue masking tape was always used to secure my Supra canopy since it was so congested in the past. I must’ve left the canopy upside down on the table as I was checking my CG. In the process, I was looking for something and the box was placed on top of the canopy such that it was taped to the bottom of the box, and I never knew it! This could be a comedy skit, ending in tragedy of epic proportions. I do remember thinking the canopy had to be somewhere in the garage as I would never lose track such a thing.

The moral of the story, never leave tape sticky side up, you never know what is going to latch onto! Now I have redundancy since I ordered another canopy.
Posted by Tazkiller85 | Jul 24, 2021 @ 05:06 AM | 17,660 Views
Yep Les Amis,
Toujours de bonnes performances ! Nous testons et comparons aujourd'hui le nouveau BetaFPV PAVO30 HD par rapport son homonyme analogique, un petit 3" puissant, lger et trs polyvalent. Des rglages propres et une conception originale font de cet engin un appareil l'aise en cinmatique et cruising et qui se dfend pas mal en freestyle. En 3S il sera doux et ultra prcis en mode stabilis mais en 4S il pousse fort pour un engin de cette taille. En bref, rsistant, puissant, prcis et polyvalent, ce nouvel engin reste mon "chouchou" du moment ... Prenez soin de vous et merci tous pour votre soutien .

BetaFPV PAVO30 HD - Review Test Démo - Résultat Concours Permanent ! (35 min 52 sec)


NOTATAZ : 19/20 Aussi bien que son petit frre en Analogique !!!
Dbutants et Aguerris !

Chez Banggood : (Vous n'aurez pas de taxes supplmentaires)
- BetaFPV Pavo30 HD (coupon BGMATT7 ) : https://bit.ly/3gXcdEG
- BetaFPV Pavo30 Analogique (coupon Cholldrons72 ) : https://bit.ly/2T5w5LX
- Lipo 4S 850mAh Tattu : https://bit.ly/3eQ4oyV
- Lipo 4S 850mAh KRATOS : https://bit.ly/36WFqth
- GEPRC VTC6 18650 4S 3000mAh : https://bit.ly/3hv9Usi
- Hlice D76 3" 5 Pales Aliexpress : https://s.click.aliexpress.com/e/_9IxT82
- Camra SMO 4K ( coupon BGFPV25 ) : https://bit.ly/3fd6rw6
- Accessoires SMO : https://bit.ly/33G83Jq
- Logiciel Insta360 STUDIO 2021 : https://www.insta360.com/fr/download/insta360-onex

Groupe FB...Continue Reading
Posted by mechmove | Jul 24, 2021 @ 01:21 AM | 14,022 Views
Some of you reading this might think I am writing about nothing. The purpose of this blog is document all my changes so I can come back to it. The reason it is public it forces me to make an effort to be clear and concise and even if no one is paying attention, there is some degree of accountability by virtue of it being public. I do reedit my blogs until I am happy it represents my ideas or facts correctly.

Changes to the ship: The included polyhedral wing joiners will be used to produce more lift. The more the better! The 12 gram wire reduction directly underneath center section that joins the fuse will not affect CG, therefore it will not be re-checked. This change does make it easier to attach the center section to the fuse. After looking closely, I decided not the trim the tail servo wires.

The new 100 amp bullet connectors at the ESC that attaches to the battery seems to be loose. When the connectors were first installed, it took an effort to connect both, but now it just slides in a out. NOT GOOD. The chances of an inflight detachment are very small, however I don't want to risk it. I made a "6mm male bullet primer" which is a piece of tapered wood to reshape the male connector back outwards so there is pressure when it inserts into the female connector. Am I the only one to notice this problem? Also, cardboard and tape will be used since I lost my canopy.

Changes to the radio program: a bit more throw for the UP elevator, (50->75 percent).

Another...Continue Reading
Posted by HOTMAILcity | Jul 23, 2021 @ 11:21 AM | 16,143 Views
1 ◄► It may have been a comedy, or it may have been a tragedy .. (تقدير) estimate sth. / etwas einschtzen .. It cost one man his reason, it cost me a blood-letting, and it cost yet another man the penalties of the law. Yet there was certainly an element of comedy. Well, you shall judge for yourselves.

I remember the date very well, for it was in the same month that Holmes refused a knighthood for services which may perhaps some day be described. I only refer to the matter in passing, .. verb (قدر ) = (take into consideration) .. for in my position of partner and confidant I am obliged to be particularly careful to avoid any indiscretion. I repeat, however, that this enables me to fix the date, .. ( fix / أورد) .. which was the latter end of June, 1902, shortly after the conclusion of the South African War. Holmes had spent several days in bed, as was his habit from time to time, but he (emerged / ورد) that morning with a long foolscap document in his hand and a twinkle of amusement in his austere grey eyes.

"There is a chance for you to make some money. friend Watson," said he. "Have you ever heard the name of Garrideb?"

I admitted that I had not.

"Well, if you can lay your hand upon a Garrideb, there's money in it."

"Why?"

"Ah, that's a long storyrather a whimsical one, too. I don't think in all our...Continue Reading
Posted by Carol ZEEE | Jul 23, 2021 @ 04:23 AM | 16,066 Views
Hello Everyone ,

This is Carol from ZEEE POWER , we are a lipo battery supplier , though I worked in this area for several years ,but this is the first time to be here

Hope I could post our battery ads at here ,Hope it won't trouble anyone ! if anyone is interested in our battery ,please feel free to contact me

Have a good day !

Carol
[email protected]
https://www.zeeepower.com/
Posted by kopterheld | Jul 23, 2021 @ 02:04 AM | 15,563 Views
BetaFPV ExpressLRS Series
https://bit.ly/BF2ELRS
BetaFPV has a whole range of ExpressLRS components like the F4 1-2S AIO Board with 2.4GHz ExpressLRS, the ELRS Nano TX Modul fit in the radios: X-Lite, X9 Lite or TBS Tango2, ExpressLRS receiver is 0.7g light and the HX115 LR Toothpick

Video
BetaFPV ExpressLRS Nano TX 2.4GHz Modul Empfänger binden (7 min 40 sec)

(with EN subtitles)
Video 2 - ExpressLRS Nano to Micro TX Adapter DIY -
BetaFPV ExpressLRS Nano to Micro TX Adapter DIY (1 min 6 sec)
...Continue Reading
Posted by RC Roundtable | Jul 22, 2021 @ 05:39 PM | 16,045 Views
Episode 133: "Oshkosh Bound" is now live!
http://www.rcroundtable.com/podcasts...pisode_133.mp3

In this episode, the gang talks about new models, TRUST, and vacations both taken and planned.
-Fitz's new camera (2:55)
-OSMW Bat (12:45)
-3D-printed T-2 Buckeye (17:45)
-TRUST (29:20)
-Floating Terry (44:10)
-Scobee Swap Meet (51:25)
-Lee's Oshkosh Plans (1:03:45)
-Winner (1:16:00)

You can visit our website at RCRoundtable.com to listen over the web or download an MP3 of the show. Or, you can subscribe to RC Roundtable on iTunes.

We would love to read your comments and ideas. Please drop us an email: [email protected].