Posted by TMacFPV | Today @ 12:10 PM | 400 Views
Simple OpenTx for FPV Quad pilots 🤩

Some FPV quad pilots may be relatively new to FPV OR are transferring over from other operating systems to OpenTX and are unfamiliar with what it is, how it works, and how to use its features. It CAN be a steep learning curve yet doesn’t have to be!
Short video streamlines OpenTx for FPV Quad pilots with basics & essentials demonstrated.
Concept of OpenTX info flow demystified so you can implement features on your own! 👌

NOTE: At about the 3:15 time hack mark I speak of binding the receiver in DI16 mode. "Props" to Roger Hughes for reminding me that "Please note that viewers do not necessarily want to select D16 for FrSky with the muti protocol module. If you try this in Europe it will not bind. You have to scroll on passed D16 to either LBT(EU) or LBT (8 chan) for D16 in the EU"
JUMPER T16 OPENTX BASICS (14 min 27 sec)

Posted by turbinefancy | Today @ 06:19 AM | 802 Views
Turning & burning with a Freewing F-14 Tomcat via head-tracking FPV in a FMS PC-21. I could barely keep pace pegging full power from the start while the Tomcat was only at half power. Still, it was a lot of fun and seeing the Tomcat in the air is like recreating TOP GUN.

FPV F-14 Tomcat Chase (4 min 5 sec)

Posted by Tazkiller85 | Today @ 06:04 AM | 813 Views
Yep Les Amis,
Le pouvoir au creux de la main ! J'ai été agréablement surpris lors du test de ce petit Snaptain SP300 . Les 3 façons de le contrôler en font un engin très ludique pour les enfants et promet de bonne parties seul ou à plusieurs . Prévoyez un peu d'espace pour utiliser le contrôle par capteur infrarouge, sinon, utilisez une des deux radiocommandes fournies. Le pilotage avec le bracelet vous surprendra par sa facilité, précision et sa réactivité . La radiocommande "haricot" est peut être toute petite, mais elle s'adaptera parfaitement à la main des enfants et elle propose un maximum d'options de vol, très pratique pour apprendre à piloter ou juste pour "se la péter" devant les copains ou les parents ! En bref, j'adore ce petit kit aussi complet qu'original ! Bon film et bon vol à tous !!!

Snaptain SP300 - Review Test Démo - Contrôler avec la MAIN ou ... Sans les Mains ! (30 min 22 sec)

NOTATAZ : 18.5/20 High-tech et Ludique !

Niveau : Enfants ... ou pas ! lol
Les + : Ludique, stable, réactif, solide, nombreuses options de pilotage.
Les - : Radiocommande un peu petite, Portée env 30 à 50m .

Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous :

- Snaptain SP300 :
- Autres produits Snaptain :

- TOUTES LES PROMOS ET COUPONS BANGGOOD 2019 (remis à jour régulièrement, gardez ce lien en favori ou...Continue Reading
Posted by Tazkiller85 | Today @ 05:23 AM | 817 Views
Yep Les Amis,
Le résultat est Topissime !!! Après avoir testé quelques caméras de surveillance Wifi individuelles, j'ai décidé d'équiper mon domicile d'un VRAI système 4 caméras, complet, filaire et fiable. Je vous présente donc le pack que j'ai sélectionné, le REOLINK RLK8-410B4 . Ce n'est pas le plus haut de gamme mais il est déjà hyper complet et suffisant pour mon utilisation. Même si ce genre de système n'empêche pas tous les cambriolages, non seulement il en évitera certainement et surtout, il rassurera votre assureur et permettra peut être de retrouver les malfrats (et donc, vos affaires) . Sans parler des voleurs, il permettra également de surveiller les endroits stratégiques de votre habitation, parking, enfants, animaux, portail etc ... Bref, un excellent et rassurant système " plug and play " pour toute la famille à installer sois même. Bon film à tous ...

REOLINK Caméras de surveillance NVR 2Go - Réglages Paramètres - Un excellent système ! (36 min 17 sec)

NOTATAZ : 18/20 Complet et Efficace !

Niveau : Bricoleur ! lol
Les + : Complet, HDD 2To intégré, Facile à paramétrer, Très sécurisé
Les - : Passage des câbles fastidieux...

Les produits présentés sont visibles ici (en cliquant sur ces liens vous soutenez ma chaîne) Merci à vous :

- Système présenté (RLK8-410B4) :
8 % de réduction permanente sur tout le site avec ce code : ytbtazk
- Produits REOLINK sur AMAZON.FR : ...Continue Reading
Posted by old4570 | Today @ 01:25 AM | 985 Views
A true 4ch Micro ... ( 1s ) with stability .

A) Protocol (?)

Yeah , no idea folks . I ran thru all the protocols available on the Jumper T12 Tx and no bind . This is a shame as I think a Hobby Grade Tx just might do wonders for such a small plane .

B) Transmitter

Not complete rubbish , the Tx does seem to offer better than the usual fare of control .

C) The Plane ( Boss )

Not bad , comes fully assembled except for the landing gear which needs to be plugged in ( easy ) . Only issue was that things ( landing gear ) was not very straight . Even the tail wheel was pointed somewhere other than straight . ( Not the end of the world ) But a little bit of straightening was needed as well as a little glue . I took the Cub out in the back yard less battery and gave it a chuck ! I was simply amazed by how well it glides . Without battery CG looks to be about 40% back from the LE . Speaking of batteries , I should have some to play with in my collection .

It's a little breezy right now , but hopefully the wind will ease off for the evening . ( I hope ) So might be able to get in a flight ?

Volantex Sport Cub 500mm 4ch ( Maiden Flight ) (5 min 8 sec)

Wow !
Flew right out of the box !
And I was actually flying @ minimum throttle ( As low as it would go )

A) It flies out of the box
B) After about 5 minutes battery was 3.92v
C) It will fly slow , really slow .
D) It can fly relatively quick as well
E) It is...Continue Reading
Posted by drewdb | Yesterday @ 10:31 PM | 1,195 Views
Making the Scene a bit more interesting. Glossy floors.

To do:

Remove shine from tyres. (not good for cross wind landings on a wet runway)
Fix normals on rear retract covers. (was fine in blender render but Daz Studio picks up everything)
Make the glass transparent to see the seats inside.

This was 16 minutes to 87% so a vast improvement on render times.

I think i'll render a few before posting again rather than 1 per post

I appreciate the comments.
Posted by drewdb | Yesterday @ 07:13 PM | 1,257 Views
Onto adding Camera Focus.

And my fav Pipistrel Panthera in the background. See it better once i have the focuse settings correct.

I think she's getting bored of standing in the one place for long periods of time

or that's a look of contemp?

A very complex involved process but i think the end result is going to be great and will certainly feature my favorite plane
Posted by jmxp69 | Yesterday @ 07:02 PM | 1,233 Views
Had the chance to fly the Detrum MSR66A iStone Sport RX/Stabilizer in some high winds today. It did pretty good...
Detrum MSR66A iStone Stabilizer Torture Test (10 min 49 sec)

Posted by unboxingexp | Yesterday @ 12:37 PM | 1,456 Views
Here is my take on a TBS Source One build. I'm using Diatone Mamba F405 MK2 flight controller, Emax 2306 1700kv motors, Runcam Nano, Beitian BN220 GPS and Eachine TX805. TPU parts are printed on my Ender 2.
Freestyle FPV drone build (4 min 17 sec)

Posted by Mad_angler1 | Yesterday @ 10:28 AM | 1,680 Views

The Ardupilot team have announced an update due a critical I2C Storm bug being found in some versions of Ardupilot.

More Info

In Copter versions 3.6.10 and Plane 3.9 or earlier thisI2C bug has the possibility to cause an Autopilot to lock up mid flight.

It is advised all users Upgrade Copter to 3.6.12 and Plane users install Plane 4.0 or later.

The Dev team state

Copter-3.6.12 has been released as the official default software for MultiCopters and Helicopters.

For those flying 3.6.10 (or earlier) the upgrade is Critical to avoid possible lockups due to I2C storms. These situations are rare but we have seen enough of them that we strongly recommend upgrading.

For those flying 3.6.11, your vehicle is probably safe but we still recommend upgrading to 3.6.12 because it includes a fix to another rare case of I2C storm lockups caused by extreme interference on the bus. We have one reported case which involved a serial port inadvertently connected to an I2C port.

The upgrade from earlier versions of 3.6.x should be relatively painless with no re-calibrations required unless you see pre-arm checks prompting you to do so.

The two new changes in 3.6.12 are in the ReleaseNotes 6 and copied below.

Fix ChibiOS I2C DMA error
COMPASS_SCALE param to allow manual correction of compass scaling
The second issue allows users to work around a compass scaling issue with the Hex Here2 GPS/compass unit. The Here2 compass unit’s scaling is off by about 17% meaning setting COMPASS_SCALING = 1.17 should improve accuracy. The accuracy can be checked before and after this change by:

fly the vehicle in any mode but ensure the flight includes chaning the vehicle’s heading
download the dataflash log and check the NKF4.SM values which are the compass’s “innovations” (the difference between the expected values and actual values). Lower is better so hopefully Here2 users will see lower values after setting the COMPASS_SCALING value to 1.17.
Note: beta testing of Copter-4.0.0-rc3 will resume next monday (Dec 16th).

Posted by GroundControlRC | Yesterday @ 10:28 AM | 1,598 Views

DustOff #2 - MinimumRC Nano F8F Rare Bear Stall Turn Practice

Here is a link to the Video:

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #MinimumRC #RareBear #F8F #Nano

I now have pretty good thrust with this Motor & Prop!
A Poster asked a question in a previous video of why I hadn't performed any Stall Turns?
Well, most of the Aircraft I have experience with do not have Rudders which makes it impossible to do a Stall Turn.
I've never attempted a Stall Turn so in this video I'm practicing Stall Turns.
Let me know if I did it correctly or really messed up ;-)

Here is a link to the Playlist which also includes the Build Tutorial Videos:

You Can Help Support Us By Using Our Affiliate Link To The Product Below. A small commission (At No Cost To You) helps us buy more items to review.

Here is a link to the Pro PNP Version of this Kit:

*Banggood no longer has the Pro Version, however, you should be able to add another servo for the ailerons to get full 4 channels, this may require a MOD to the fuselage.
Also, the 3 channel comes with a 720 motor but I like the 1020 Motor ;-)

MinimumRC F8F Rare Bear 360mm Wingspan KT Board Mini RC Airplane KIT With 720 Coreless Motor - KIT+Motor+Servos

MinimumRC Rare Bear Spare Props - Hole Diameter...Continue Reading
Posted by phyngineer | Yesterday @ 04:00 AM | 2,024 Views
UAV applications: scientific exploration

I. Background

In recent years, international aviation geophysical exploration flight platforms have developed from traditional manned aircraft to drones. At the same time, whether the performance of aerial object detection equipment meets the working requirements is also an important factor limiting the use of UAVs in geophysical exploration. If the performance parameters of the detection equipment are up to standard, the application of UAVs in geophysical exploration will have a very broad application prospect.

1. Main applications abroad

UAV technology has been widely used in various fields in geophysical exploration abroad and has achieved good results, which has greatly improved the quality of scientific research. These have a very good reference for China's related technology applications.

Magsurvey Limited in the United Kingdom provides drone detection of the Earth's magnetic field. The literature describes the use of small fixed-wing drones equipped with magnetometers to detect oil, gas, and mineral resources. Point out the reasons for using small fixed-wing drones as mobile platforms:

① Mission load-cesium light pump magnetometer with high accuracy and lightweight (less than 1kg), the small unmanned aerial vehicle can fully carry;

② Small UAVs can fly near the ground (flying height less than 20m), and can obtain more accurate detection data;

③The drone is equipped with advanced GPS /...Continue Reading
Posted by drewdb | Yesterday @ 02:02 AM | 2,141 Views
An idea of the direction i'll be taking this music video.

The Jet just needs a coat of paint.

Hands up who didn't notice the Jet in the background

Well obviously Pilot Gwen didn't as she has both hands up. Much to our delight

Messing around with hair animations so she needs a stylist at the moment
Posted by Blaze0021 | Yesterday @ 01:39 AM | 2,132 Views
I was never a fan of the stock green Eflite scheme, so my first impulse was to customize my UMX F-27 Evolution with the color scheme of my choice.. Black!

Eflite UMX F-27 Evolution Flight w/ Custom Black Trim Scheme (4 min 50 sec)

I carefully peeled the stock stickers off, applied them to an old decal backing sheet that I kept from a previous project. I then applied two spray coats of Krylon Supermaxx Black, allowed it to dry, and then reapplied them with Elmer’s Crystal Glue, using an epoxy brush.

Aside from the custom “Black” scheme, Dubro 1.25” Nose Skid and Small Parts CNC Aluminum UMX Prop Adapter, all of the internals are stock. Powered with an Eflite 3S 300mAh 30C Lipo (27 grams), placed as far back in the battery compartment for an aft-most CG.

Thanks Brad for catching the flight footage!

Thanks for watching!!
Posted by alex_nikiforov | Dec 12, 2019 @ 11:12 PM | 2,171 Views
Foxeer Razer Mini / Micro 1/3 CMOS 2.1mm / 1.8mm Lens 1200TVL 4:3/16:9 NTSC/PAL Switchable FPV Camera For RC Drone
Foxeer Razer Mini / Micro. Бюджетная камера всего за $16. (10 min 2 sec)

Razer Mini
Razer Micro
Posted by CarlosSM | Dec 12, 2019 @ 09:37 PM | 2,207 Views
Hi Guys,
I have been flying RC for a long time, lately I got really into free flight and I'm new and willing to learn. Where can I buy the system to wind the rubber band outside the plane? I'm flying old timers 30-40" WS Thanks for the advise.
Posted by Reckless_fpv | Dec 12, 2019 @ 06:15 PM | 2,318 Views
Just want to say thanks everyone for all the support! 🔥 🔥 Its been so much fun growing with everyone! 🍻 🍻 My channel has blown up this year! I wouldnt be able to fo any of this with out all your support, eventually the goal is to make a living doing this! I know its a long shot but last year so was getting to 1000 subs but here we are! 🔥 🔥 Thanks again everyone! If you wanna go the extra mile heres the link to my patreon :
And if you would rather just get a shirt hoodie or stickers heres my teespring
I plan on making fitted hats, backpacks and fancy prop bags soon! 🔥 🔥
Posted by GBLynden | Dec 12, 2019 @ 06:05 PM | 2,305 Views
Here is my weekly RC stream from last night featuring the sexy E-flite Su-30 Twin 70mm EDF Jet!

Hump Day RC With GBLynden - I Am Alive, E-flite Su-30 Twin 70mm EDF Jet, & More! (2 hr 10 min 45 sec)

Note: I show the plane at around the 52 minute mark and go into detail with up close shots of this beautiful plane!
Posted by old4570 | Dec 12, 2019 @ 05:27 PM | 2,356 Views
Black Friday

Almost 20 items in the limbo called MAIL !
Where's my stuff !!!!

Purchased my Christmas ( Xmas to some ) presents to myself ( who better to chose something to buy ) ..
Yes , was not after shirts or socks or any other nick naks ! No it had to be RC related ...
Folks at Banggood had a recent sale and a certain 4ch Cub was on sale and I got it for the same $$ as a WL toys F959
One can only hope it gets here for Dec 24 ( Last day for some snail mail ) .

A BIG THANK YOU to anyone and everyone that used my Affiliate links to buy stuff , earning me some BG points .
When you buy a lot of stuff ( I cant help it ) , every point helps .

Hmmm , Black Friday !

Do I window shop or blow some dust off my wallet ? ( Wait ) Didn'y I just spend money ? I'm a bad boy !
I have a Bee 490 staring at me

Still Ho humming over it's stuffing ..
I just might have to do a F959 flight pack onto it ( Control board / motor / folding prop )
Also that 450x with the F949 control board , needs work - Roll rate is way soft . Control horns might need new holes ..