Posted by GroundControlRC | May 29, 2020 @ 07:30 AM | 3,941 Views

Glue & Fly™ Series - F-22 Nano V1 - Flight #8 - It's a Keeper ;-)

Tuned and ready to see it's capability ;-)

Banggood GCRC

Here is a link to the Video:

Here are links to all the Components I chose for this Nano Parkjet:

HappyModel EX1102 13500kv Brushless Motor (1.5mm Shaft - 13500kv)

***Receiver I used (Make sure the Receiver you choose matches your Transmitter Protocol!)
Receiver 4CH Low Voltage DSM2 DSMX

***Servos (I have ordered these and the ones they sent did fit the Micro Receiver I have. These were JST-SH 1.25mm Pitch on the Connector)
2Pcs 1.7g Low Voltage Micro Digital Servo Mini JST Connector for RC Model

10 Pairs LDARC 2.5 Inch 65mm-2blades Racer Propeller(hole diam:1.5mm) M2 Screw Fixing For Toothpick FPV

I cannot find the DYS 7A OPTO ESCs any more.
I have just received this 7A OPTO ESC but I have not tested it yet.
1-2S 7A Brushless ESC High Speed For RC Airplane

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #GFSNanoF22 #GFSNanoF22V1

See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Ground Control RC™ Glue & Fly™ Series Scratch-Build Planes

Consider Supporting Our Channel by becoming a Patron at:
Patrons of the Channel will have access to the latest Aircraft Plans & Exclusive Content!

See Us On Youtube | Patreon | RCGroups
Posted by 1stGeppetto | May 29, 2020 @ 04:16 AM | 4,122 Views
Completed May of 2020. Glass over wood with finished with rattle can paint.
Posted by 1stGeppetto | May 29, 2020 @ 04:13 AM | 4,046 Views
Completed in September 2019. Polyspan covering, Nitrate Dope to attach and fill the weave, Butyrate Dope for colors.
Posted by 1stGeppetto | May 29, 2020 @ 04:09 AM | 3,707 Views
Completed in March of 2020. Mad Max meets Steam Punk.
Posted by Amanda BH | May 29, 2020 @ 03:07 AM | 3,374 Views
Brotherhobby Hyperbola 5" BNF drone , the frame is T800SC-24K carbon firber.

Mostly, the frame use T300 or T700 carbon firber on the market

Hope you can get more information from the attached pictures
Posted by Eric Zhu | May 29, 2020 @ 02:34 AM | 3,163 Views
AGFRC A81BHMW 45KG IP67 Waterproof Digital Steering Servo High Torque Programmable Full Metal Gear Brushless Servo for 1/8 1/10 RC Models, 180 Degrees

The AGFRC A81BHMW Waterproof Programmable RC Servo is an upgraded version of the A80BHSW Waterproof Programmable Servo, which overall improves the performance and quality. The maximum torque is increased from 36KG to 45KG, the strength of the bearing is improved, and the collision resistance is stronger, making this A81BHMW servo more suitable for applications in 1: 8 scale RC model such as off-road and climbing car, etc.

This A81BHMW servo is also a member of AGFRC PROGRAMMABLE SERVO, equipped with AGF-SPV2 servo programmer (included) which can change the torque, speed, angle, and other parameters of the servo what you want, even 360 full range angle or 720 angle, etc. It's really convenience for users to DIY the parameters of their servo according to the situation.

Moreover, the manufacturer will continue to UPDATE the various firmware of the A81BHMW servo, users can download the updated file from the manufacturer's official website to update it through the AGF-SPV2 servo programmer in the future.

Name: 6.jpg
Views: 4
Size: 2.62 MB

  • AGFRC Waterproof digital servo uses high-precision production technology to reduce production deviation and improve product tightness, used IP67 Waterproof design, can be common use in RC climbing cars, 1:8/1:10 Buggy, RC boat, helicopter, robots, mechanical arms, and others RC model.
  • Good choice for
...Continue Reading
Posted by Nickerz | May 28, 2020 @ 11:32 PM | 3,022 Views
This morning, I bought a 2nd Great Planes PT-40 but this is the original PT-40 that came out around 1987 I think (whereas version 2, the MKII came out around 2008) and I bought this original version 1 from an member. Total paid was...

$100.00 (Grand Total)
$100.00 (Plane ARF Kit, Engine & Radio!)
$Free (Shipping)
$N/A (Tax)

This is NIB and I wanted this to keep for nostalgic reasons since this is technically the plane I viewed in the two videos I had as a kid and wanted to buy back then but I felt building it would have been a little more than I was ready for. So now I have that chance and I got such a great deal on this as they go for $250+ on eBay! USPS shows the delivery date between TBD...

Here is the original classified ad...

I already have an engine for it too (NIB O.S. MAX .40-FP which is the original engine recommended in the manual and in the videos I watched as a kid!) I'll take pics and do an unboxing video once I get it. Here's a pic from the seller...

Posted by AlkaM | May 28, 2020 @ 08:56 PM | 3,418 Views
Many of you will be familiar with some of this already. I skip a lot of things about switching losses and current circulation in the motors. This is about how these two electrical variables affect real world performance. This is to hopefully give an idea of what PWM even is to those unfamiliar.. feel free to post your comments experience down below.
Motors are driven by voltage. In order to control the voltage that a motor coils "pulse width modulation" (PWM) is the process by which this happens. If you have a 12 volt battery and want to run the motor at half speed (6 volts ) you would use pwm with a 50 percent "duty cycle". This means half the time the switches are ON that drive the motors coils and half the time they are OFF.
Pwm frequency ( 24khz, 48khz etc) is the number of times per second that these switches are turned on or off. You could do pwm yourself and probably manage a few switches per second. So picture a toggle switch, when the switch is turned on the current starts to rise in the motor coils and the motor begins to move. When its off the motor will coast and begin to slow down. At a very low frequency like this you can see that it might be hard on a motor as the current goes through large swings with each turn on turn/ off phase. This current ripple creates heat in the motor coils and is a major power loss. To make it smoother you need to increase the frequency. Ideally, to switch fast enought that the current has not enough time to...Continue Reading
Posted by lawrence4 | May 28, 2020 @ 08:17 PM | 3,197 Views
Test use Beta75 pro 2,
Benefit from longer flight time and cooler motor.
More smoothly under 1S 0.5 startup power.

1.flashing the support bi-directional DShot firmware(for RPM filter),
download the latest firmware marked “48KHz”.
Firmware that allow to run RPM filter in BLHeli_S ESC for free JazzMaverick:

Firstly find out the code name of your ESC.
Connect to BLHeli Configurator.
You can see your ESC code name in the title, for example, mine Beta75 pro 2 is S-H-50 and download the firmware S_H_50_48_REV16_8.HEX

Update your FC to Betaflight 4.1 or newer(for now mine is 4.1.6)

Use 4KHz gyro sampling rate and 4KHz looptime.DShot300 ESC Protocol.
Enable “Bidirectional DShot“, and set Motor poles (for example Beta75 pro 2 motor 08028 is 12 poles)

Under Dynamic Notch Filter:
Filter Range at LOW
Width Percent to 0
Q factor to 200
Min frequency to 90

If the motors are cool, it probably means you can reduce filtering further. But this time you can use the two sliders on the top of the filter tab – Gyro Filter Multiplier and D term filter multiplier.(I test it at 1.2 both)

Reference (details explanation):
3.BLHeli Configurator:
4.BLHeliSuite for BLHeli_S: (download link in the bottom “Read Me” section).
7.Bidirectional DSHOT and RPM Filter:
9.ImpulseRC driver fixer download:
Posted by stevster | May 28, 2020 @ 07:37 PM | 3,339 Views
Here's some pictures of my latest "Covid19 Build". It's a plans built, 1930, 1/4 Great Lakes Trainer 2T-1A
I really enjoyed this build. It was fun to detail. 80" span @21 1/2 lbs. Should putt around like a dream trainer.
Powered by a Sachs 2.4 gasoline engine on electronic ignition with a Sullivan smoke system built into the muffler.
Covered in original, uncolored, Super Coverite, stitched, rib taped, sealed with 2 coats of Minwax Polycrylic polyurethane,
then 2 coats of primer (with a sanding of a Scotchbrite pad between each coat) then finished it off with 2 coats of Rust-Oleum
Gloss Protective enamel. I made my own graphics on my wife's Cricut vinyl cutter. That's fun! Topped it off with a couple
off Bazzboe's (here on RCG) very cool 1/4 scale pilots at the "controls". Maiden coming soon!...Continue Reading
Posted by VicT | May 28, 2020 @ 04:04 PM | 3,180 Views
I purchased an open stock AR637T receiver a few weeks ago and finally got about 5 minutes of flight today (5/28/2020) after replacing the AR636 receiver that came with the Turbo Timber (TT). The TT had flown the day before and I had programmed her with 5 flight modes using the throttle stick as 1 switch for 3 modes and the D switch for 2 modes. Dual rates, expo, and mixing had audio working fine. I removed the 636 RX and white silicone from the foam and made a plywood floor for the 637T RX. I followed the installation manual and bound the RX to the TT program. I had to reverse the elevator and aileron servo direction. She flew the next day and without SAFE or AS3X I noticed my TT as being very sensitive and not forgiving like the 636 RX.

I had been following the manual included with the receiver and got this far before asking Dave A. HELP.......

Forward Programming -> Gyro Settings -> First Time Setup The transmitter will prompt you for all setup steps.
IMPORTANT: Before proceeding with setup, read every information screen that appears on your transmitter
Select NEXT at the bottom of each page to continue.
3. Followtheon-screenpromptstosettheorientation.SelectContinueto complete the two-step auto detection process, or select
Set Orientation Manually. Verify the orientation is correct.
4. Youcanassignanyopenchanneltoaswitch(trimmer,knob,e tc)forgain, and assign that channel for gain. You can assign a switch to a channel from the Forward Programming menu so you don’t have to exit the menu. We recommend using a trimmer, knob, or slider for gain, which will enable you to change the gain value on the fly.
When the setup screens are complete select Apply.
3. AS3XTuningBasics:
1. Perform a control surface direction test, and AS3X reaction test.
2. Test fly the airplane to verify the configuration. In-flight trim changes do not require any further updates.
Posted by Justwingit | May 28, 2020 @ 02:27 PM | 3,499 Views
So I've been flying my E-flite UMX Cessna Citation Longitude as a belly lander recently...


This thing is NUTS !
E-flite UMX Cessna Citation Longitude Twin 30mm EDF - This thing is NUTS! (10 min 44 sec)

Enjoy the show and I wish everyone all the best !

Posted by phil alvirez | May 28, 2020 @ 11:46 AM | 3,654 Views
see parts 1-3 at my blog
from time to time, model airplane magazines published articles on sort of science fiction by mad scientists that were performing experiments with remote controlled airplanes.
these were as rudimentary as they could be. free flight planes controlling just the rudder, and that happened erratically. it was sort of lottery to be able to change the direction of the plane now and then.
but, as i said, it was just trying the boundaries of the then fantasy of controlling something at a distance.
this took years and the contribution of countless (and nameless) folks to reach the point of being able to control also elevator, then throttle.
the gear consisted on a car battery placed on the ground that provided the power, connected to a control box that the modeler held in his hands.
those who were present were in awe, and talked about this for a long time to whoever were around.
then came reeds, that improved efficiency. there was 1 channel for left turn, and another for right turn.
when elevator was added, same thing: 1 channel for up, another for down.
then servos. nicads. years later, some1 released the 1st commercial radio control (kraft, i think). and expensive. heavy.
and they were flying on frequencies (72, 27), so you would not have interference.
i recall at los angeles, there was at a place called mile square, that was an emergency airstrip (dont know of still exists), that had large areas designated for each frequency where the ones that were willing to fly formed and awaited for their turn to fly.
it was until, on 2006 that horizon released the 2.4 with which apparently any number of planes could fly without interference.
now we also have cellulars, laptops, gps and whatnot.
boy, the world has come a long way...
Posted by DutchRC | May 28, 2020 @ 11:14 AM | 3,626 Views
Halloa people,

soooo it has been a while since Runcam released the Runcam 2 right? I'm not completely sure but it must have been 4-5 years
Back then the RC2 was a great action-cam option for multirotors and it indeed was the first recorder I strapped onto a quad :P

But.. time moves on and we now finally have a 4K version of it!
The shape of these camera's also make them handy for airplanes which is indeed what I was still using the RC2 for

Link to the new cam: Runcam 2 4K edition - Pillbox style action camera

BUT.. is it any good??

Runcam 2 4K Edition Action Camera! (finally :P) - REVIEW (25 min 0 sec)

shape: pillbox
max video res: 4K (at 30 fps)
max frame rate: 120 at 1080P
shutter speed lockable: yes
ISO lockable: yes
video codec: MP4 - H264
max photo res: video only
field of view: 155 degrees
max CF card size: 128 GB
microphone: yes
external microphone: ?
gyro stabi: limited
WIFI config option: yes
battery: 850 mah 1S Lion
max recording time: 1.5 hours at 1080P 60
viewfinder screen: on phone via WIFI
touch-screen: nope
second (front) screen: nope
usb-type: micro USB
water proof: nope
Posted by GLSJr | May 28, 2020 @ 09:06 AM | 3,862 Views
I have been trying to find some information on the toxic effects of soldering fumes. Now that I have switched over from nitro to electric, I am spending A LOT of time soldering. Web searches always assume I am talking about wave soldering in a factory. Does anybody know of a site that can give me an answer to this? I can only hold my breath so long. Thanks
Posted by GroundControlRC | May 28, 2020 @ 07:02 AM | 4,458 Views

Yak54 Aerobat EPP 800mm Wingspan 3D Plane - Flights 3 & 4 - It's a Keeper ;-)

Yak54 Aerobat 800mm Wingspan Kit

Banggood GCRC

Here is a link to the Video:

I can't stop flying this Plane!
This is going to be an excellent 3D Trainer for me and it's a blast just doing these Slow, Graceful, Maneuvers with this Plane.
It's definitely worth the time to build.

Here is a link to the Playlist which also has the Assembly videos:

RC Tip #24 - Servo Setup & Centering - Get that Servo perfectly Centered

This Yak54 Aerobat Kit is Courtesy of Banggood.
I want to thank Banggood for sending this Kit for Review.

Here are link to the Components I used in this Kit 3D Plane:

Yak54 3D Aerobat 800mm Wingspan Kit

Servos - 6PCS Racerstar SG90 9g Micro Plastic Gear Analog Servo (I used some old EXI 9g Servos I had on hand)

Motor - RacerStar BR2208 1400kv 2S-4S

ESC - Htirc Hornet Series 12A 2-4S Brushless ESC With 5V/2A BEC For RC Models

Control Horns - 10X Rudder Servo Rob Angle Set With 1mm Chuck Screw For...Continue Reading
Posted by Rowhider | May 28, 2020 @ 06:04 AM | 4,598 Views
Run of yesterday with my Top-Force evo in my little garden track


Posted by | May 27, 2020 @ 06:21 PM | 10,368 Views
Hi Guys

I've written a step by step setup guide for the WL toys 144001 that has come out better than I was hoping:

-Filled the diffs with grease, adjusting the turnbuckles and correcting the amount of fluid in the shocks. This will really improve handling and substatially increase the life of the diffs and shocks. Hope you find this useful