Posted by Helen_AGFrc | Today @ 01:52 AM | 219 Views
Is there any of you play the Mini Z Car?
If yes, come and check out our the latest mini gyro for Mini Z Car.

It is the upgrade version, and The GY04M-V3 has below main features:
-CompactSizeGyro
-AluminumCoolingCase
-DualGainMode
-PWM/Sanwa/FutabaCompatible

Same Price, but more features!

It is only 21x15x8.8mm small and weight 4g.
With Dual Gain Mode, it will be high sensitivity and stability for your Mini Z Car.
Compatible with PWM/ Sanwa /Futaba which are most popular protocol in the market.
The working voltage is 3.7-8.4V (2S).
Wire connection: JST 1.5mm
Control System: PID Control System
Current Drain:20mA/6V
Operating Temperature: -10 degree to +50 degree
It is easy operation,but wonderful performance.

More Product info, please check here:
https://www.agfrc.com/index.php?id=1989&project=product

If you need more info, please feel free to contact me at [email protected]
Posted by GBLynden | Yesterday @ 11:29 PM | 370 Views
This is Bryan's Giant Scale Balsa USA 1/3 Scale Sopwith Pup WWI Biplane Maiden Flight at Warbirds Over Whatcom.

Bryan's Giant Scale Balsa USA 1/3 Scale Sopwith Pup WWI Biplane Maiden Flight (6 min 42 sec)

Posted by UpNup | Yesterday @ 09:34 PM | 487 Views
Spent this afternoon cleaning up the wings on this C G Electra. Used a rotary tool to drill out the glued balsa pieces in the center of the wings and added an aluminum strip cut from a soda can, well-sanded. Scratchbuilt 3/4” wingtips. After touching up some gaps with lightweight spackling, I sanded it thoroughly, but carefully, with 80 grit sandpaper. Cracked two ribs, not mine thank the Lord, but they CA’d back in place just fine. Working with a 30+ yr.-old, brittle, 78” 100% balsa and ply wingspan was an experience.
Posted by jmxp69 | Yesterday @ 09:13 PM | 505 Views
In this http://rcvideoreviews.com OpenTx Tutorial, I will show you how to configure Flight Modes on OpenTx and how to switch modes using the 6 position switch.

Flight Modes and the 6 Position Switch - Radiomaster TX16s - OpenTx for Beginners Tutorial (43 min 25 sec)


This is not to be confused with flight modes on flight computers/autopilots. The flight modes covered in this video are radio flight modes which allow various configurations of trims, rates, and mixes within the individual modes. This has nothing to do with stabilization, hover, waypoints, or return to home.

I learned while editing the video the 6 position switch must also be calibrated during the OpenTx hardware calibration process. I cover both calibrated and uncalibrated 6 position channel outputs in the video.

Before you attempt the techniques demonstrated in this video, you should be comfortable using OpenTx Companion and with creating mixes. You can get up-to-speed with the two videos below:

OpenTx Companion: Video
How-to Use OpenTx Companion - Radiomaster TX16s - OpenTx for Beginners Tutorial (25 min 5 sec)
...Continue Reading
Posted by BernardW | Yesterday @ 01:59 PM | 1,049 Views
I'm happy to see that the Federal Govt. has decided to withdraw its backing for Clive Palmer's High Court challenge to the WA hard border. I suspect they withdrew because very few West Aussies would likely vote for them in the next election (I think it's the 1st half of next year) if they followed through as the bid is deeply unpopular in WA, and from the little I've heard even people in the Eastern States don't like the sound of the challenge or of the Federal govt. supporting it. I'm sure that's not the reason they'll give publicly but hey, so long as they're out of it.

If you didn't know, I make a living as a live sound engineer in Perth, operating the PA system for live music in large pub venues. That was one of the first industries to be clobbered by the virus, but we've been able to work again for about a month now. Crowds in town are very busy again on the weekends when I work there. I've been talking with more of the "punters", the patrons and general public, at and around the gigs I've been to lately. From that and the media, I gather that West Aussies really do understand that we are in an extraordinarily lucky position, being able to see the footy at the stadium, go to gigs, drink in pubs, go to the supermarket without queuing, and generally living life the way we're used to. There's also a sense that that inevitably sooner or later, the virus will reappear, with that 2nd wave in Victoria and NSW. People believe it will surely cross...Continue Reading
Posted by VicT | Yesterday @ 01:45 PM | 1,108 Views
Attached is my DX9 TX file for the Conscendo Evolution with spoilerons, thermal camber and flight modes for the throttle and D switch. Audio files are included. There is a warning about charging a SMART battery. It poses no problem...just hit the clear button or wait and it goes away.

Component weights compared to CA and motor power measurement
https://www.rcgroups.com/forums/show...&postcount=312

Maiden notes and new clear canopy how to
https://www.rcgroups.com/forums/show...&postcount=400

Binding the CE637TA receiver
https://www.rcgroups.com/forums/show...&postcount=330

Fixing or replacing foam hinges
https://www.rcgroups.com/forums/show...&postcount=153

Spinner info and upgrade
https://www.rcgroups.com/forums/show...&postcount=221

Adding more wing tip dihedral for more rudder effectiveness
https://www.rcgroups.com/forums/show...93&postcount=1

Park Flyer clear canopy and fuselage plastic
https://parkflyerplastics.com/cart/i...word=Conscendo
Posted by DutchRC | Yesterday @ 11:11 AM | 1,258 Views
Howdy people

sooo Flash what?? Yeah.. a new motors-brand.. You might have come across them on sales sites..
I got my hands on a few sets SO let us see if they are wurth considering

Link to them: Flashhobby Arthur 4S & 6S 2207.5 motors

AND let's see how they perform

Flashhobby Arthur 2207.5 motors Review (and WHO is Flashhobby anyway? :O) (22 min 33 sec)

Posted by FLSharkvictim | Yesterday @ 10:11 AM | 1,432 Views
I specialize in #ARRMA RC vehicles / RC Speed Boats / Aerial Photography using unmanned aircraft technology. I make bashing & speed videos, on this channel. This will be my platform where I will be uploading my boating sessions & my bashing & blasting sessions with my ARRMA 6s KRATON / 6s Notorious / 3s Typhon and my Probaot Sonicwake 36'' DeepV Speedboat!

Please feel free to check out any of social media platforms UNDER - Uplift-RC
Posted by Basingstoke Roy | Yesterday @ 04:20 AM | 2,006 Views
Another furloughed project from my loft.

Welcome, Lets start by telling the story. Way back in the late 70s my then club mates and I were into flat field soaring (pre electric days) at Cranford Park west London. My then club was the Hayes & District Model Aero Club.

Back then throughout the summer, Wednesday night was always club comp night with trophies at the end of the year. Typical comps would be a, 6 minute duration comp with a spot landing, and 100s comps

This is where the Sailman comes in to the story. My mate Matt built and competed with his Simple Sailman & would regally win or be well placed in the comps, some times against far more sophisticated models (not mine I hasten to add). As I remember Matt did have one little trick up his sleeve, as the wing tips are removable he built a selection of differing lengths to suit the comp. Anyhow at the end of year Matt typically would take home some of the clubs silver ware.

Roll on many decades to September last year. Its my current clubs annual E-fly event and arrive one of my old club mattes from back in the day, we will call him Andy T to protect his identity! Andy had been very impressed with Matts model back in the days, so had splashed out on a kit of his own. Andy had made a start on the kit assembling the fuselage side panels, before life got in the way & eventually the kit ended up in the loft where it had stayed.

Andy been having a clearer out of his loft and rationalising his...Continue Reading
Posted by old4570 | Yesterday @ 02:22 AM | 2,213 Views
Looks like around 70 grams of thrust on 1s .
18650 carrier has been modified .
ESC is the Fatjay RS-7A 1-2s
Motor is 1811 3800kv
Prop will be 6x4 or 6x3

Push come to shove , I can 2s at a later date if needed with a Zippy 350 , or something .
Posted by charlton29 | Aug 01, 2020 @ 09:53 PM | 2,450 Views
I managed to get some (reasonable) video of the new wing in flight. It's harder than you think to shoot when you are by yourself and trying to fly the model at the same time. A camera on the transmitter helps but still it's a bit unsteady so I hope no-one gets seasick.
Here is the video, anyway:
Horten Wing (5 min 40 sec)

Posted by herreraa | Aug 01, 2020 @ 09:08 PM | 2,497 Views
Here my first mini rc plane . It is my favorite Slowly V2.
I started with a 40% so I can use some E7 mootors.

My son is the pilot, i had few chances to fly it mtself . He likes loops . I prefer some slow flight , easy to build and using dollar tree foam available.

This is a real fun plane, but as a trainer is not the best , we had a shaft bended , can fly but i am currently looking for another 30grams plane with protected motor.

Final weight : 36 grams
ws:14in
lenght: 14in
Motor:EPS_7
Motor Specifications:
Type: Brushed
Dimension: 16 x 7mm
Shaft Length: 5mm
Shaft Diameter: 1mm
Weight: 3.3g
Max current: 1.8A
RPM: 3V/40,000rpm at no load
Suggested prop: GWS 4530

Test data;
Prop: GWS 5030
Voltage: 3.3, 3.8, 4V
Current: 0.76, 0.89, 0.93A
Watts: 2.508, 3.382, 3.72W
Thrust: 31, 36, 38g
Efficiency (g/w): 12.36, 10.64, 10.22

Prop: GWS 4530
Voltage: 3.8, 4V
Current: 0.81, 0.87A
Watts: 3.078, 3.48W
Thrust: 32, 35g
Efficiency (g/w): 10.40, 10.06


Propeller used : 5030
Receiver: MX-Rx62H
Transmitter: Jumper T8SG

Slowly V2 40% RC airplane (2 min 25 sec)

Posted by g monkey | Aug 01, 2020 @ 07:11 PM | 2,677 Views
I thought that I would share my attempt to scratch build a Bell 206 JR using OMP M2 mechanics, a CAD package and 3d printing, as perhaps others might find some of this useful or have some tips to share with me.

Background
Quick bit about me. I only started flying RC helis during the lockdown, starting with a Blade Nano S2. I did fly fixed wing RC many decades ago (think AM radios) but I'm still very much a novice pilot. I'm unlikely to progress into 3d flying, but I decided to buy an OPM M2 after reading the rave reviews. The mechanical simplicity and build quality impressed me, but I really hankered for a scale heli, especially a Bell JR - I just needed a scale kit for the M2. Not finding one of a suitable size, I decided to build one. The thing is, the material of choice is not the balsa that I used long ago. The M2 is all carbon fibre and aluminium. What to do?

Inspired by several things that I have read on the web about 3d printing, different filament materials, and the appearance of downloadable 3d printed kits (both helis and fixed wing), I decided to give 3d printing a go. In the words of a famous UK motoring journo, how hard can it be? Knock it up on a PC, click a few buttons, send it to the printer and Robert is your mother's brother. What could possibly go wrong?

Printer choice
The first decision was selecting a 3d printer. I plumped for a Prusa i3 Mk3s. Widely praised in the 3d printing community and press, it seemed a sensible choice...Continue Reading
Posted by GroundControlRC | Aug 01, 2020 @ 08:06 AM | 3,467 Views


RadioMaster TX16S 16CH Multi-protocol Transmitter - Review Part 1 - Game Changer!!!

RadioMaster TX16S Transmitter
https://www.banggood.com/custlink/DvvycmfSMK

Banggood GCRC
https://www.banggood.com/custlink/GmDmQ1nVkO

Here is a link to the Video:
https://www.youtube.com/watch?v=ckl__WdrDms

I have been contemplating getting one of the Jumper Transmitters for about a year now but I just couldn't work it into my budget.
Well, now I have one Courtesy of Banggood to Test and Review ;-)
I want to thank Banggood for sending this Transmitter for Review.
One Transmitter to Rule Them all!

Here are links to the PDF File of my Setup for the Eachine Mini P51D Mustang in Letter & A4 Format:
https://www.groundcontrolrc.com/ftp/...tup_letter.pdf
https://www.groundcontrolrc.com/ftp/...d_setup_a4.pdf

RadioMaster TX16S Downloads Page:
https://www.radiomasterrc.com/downloads

RadioMaster Thingiverse page:
https://www.thingiverse.com/radiomasterrc/designs

OpenTX 2.2 Manual:
https://opentx.gitbooks.io/manual-fo...x-2-2/content/

#GroundControlRC #GlueAndFly #ScratchBuildPlanes #Jumper #JumperTX #RadioMaster #RadioMasterTX #RadioMasterTX16S
#Banggood

You Can Help Support Us By Using Our Affiliate Link To The Product Above. A small commission (At No Cost To You) helps us buy more items to review.


See you in the Air!

Build, Fly, Crash, Repair, Rinse & Repeat!

Ground Control RC Glue & Fly Series Scratch-Build Planes

Consider Supporting Our Channel by becoming a Patron at: https://www.patreon.com/groundcontrolrc
Patrons of the Channel will have Exclusive access to Aircraft Plans & Content!

See Us On Youtube | Patreon | RCGroups

https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
Posted by jmxp69 | Aug 01, 2020 @ 07:59 AM | 3,430 Views
In this http://rcvideoreviews.com video I'll show you how to use OpenTx Companion. We'll cover:
- Installation and Setup
- Creating Radio Profiles
- Reading and Writing Radio Data
- Using the Simulator to test Radio Configurations

By the time you're finished with this video you should have a strong degree of comfort with the basic operation of OpenTx Companion.
How-to Use OpenTx Companion - Radiomaster TX16s - OpenTx for Beginners Tutorial (25 min 5 sec)