Posted by djmoose | Today @ 08:12 AM | 692 Views
Mounting the Dualsky GA6000.9 motor, painting the false radial engine, and mounting the cowl is what's in this next episode of my 92" Black Horse Gilmore ARF from MotionRC. Enjoy!

How to install the motor, cowl, and paint the radial - 92" Black Horse Gilmore Red Lion ARF - Build (10 min 26 sec)

"Pratt & Whitney supplied the powerplants, Wasp Jr. engines with 985 cubic inches of displacement. The factory beefed up and supercharged the engines with high-compression pistons and individual stacks for less back pressure. In 1932, the manufacturer rated them as follows: 525 horsepower at 2,200 revolutions per minute and 550 horsepower at 2,300 RPM when racing." - Wedell-Williams Air Service page 34

"The engine cowl for the Model 44s was a NACA-type provided by Hill Aircraft Streamliners. The full pressure cowl created a venturi effect at the trailing edge for the exhaust to exit the stacks. Turner's cowl tapered slightly more inward at the trailing edge than the other two. " - Wedell-Williams Air Service page 35
Posted by OldRCGlider | Today @ 07:28 AM | 1,142 Views
Please see my eBay Profile… dpnp93
This should give you more confidence in me as a new RC Groups seller.
Thanks for looking.
Posted by benjamin presten | Today @ 03:25 AM | 2,904 Views
Rearwin 6000M Speedster: The Rearwin Airplane company began to falter at the beginning of the depression and Rae Rearwin negotiated control from his investors and started Rearwin Aircraft. The intended first offering of Rearwin Aircraft wound up being the third airplane to make it to production when it’s development took a lot of work.

The Rearwin Speedster started life powered by a Cirrus engine. Initial testing for certification found the airplane didn’t meet spin recovery standards. Between 1934 and 1938 the airplane received several changes in search of the solution. The ailerons were redesigned to reduce the gap between them and the wing. The tail feathers were enlarged and centering springs were added to the rudder. All of the control systems also received ball bearings.

By the time the Speedster was ready for production, the Cirrus engine was out of production so the Menasco C-4 was chosen to replace it. The 6000M was the final production variant of the airplane. It had a cramped cabin for two in tandem inside it’s very narrow fuselage. It had a very distinct tough looking landing gear and large tail feathers. In general the Speedster was a very unique looking ship.

At the same time as the Speedster, Rearwin was producing the Cloudster and the Sportster. They seemed to overshadow the Speedster leaving it with a final production run of only 11 aircraft. Today two remain on display. The most recent Speedster to fly was restored by Tim Talen who was...Continue Reading
Posted by unboxingexp | Today @ 02:44 AM | 3,066 Views
I put a stripped Gopro Hero 7 black on my Nanolongrange V2b design ( I was not sure if it will fly as it got pretty heavy at 131g. Still It worked out and now I'm pretty stoked. I think I can make it even 15g lighter. So stay tuned!
Nanolongange V2b with stripped Gopro Hero 7 (6 min 1 sec)

Posted by RCWorks | Yesterday @ 11:56 PM | 5,658 Views
I started my jointer project. It was a mess this picture was taken after taking a coarse sharpening stone to the top for a good hour. It had a layer of rust on it that was beginning to pit the surface.

I could have opted to build a fixture and have the in and ot feed tables ground but I don't think it was worth the time and expense.

I ordered new knives and bearings for it.

Someone had been in it for bearings some time in it's past and was a bit brutal to it with a hammer. It had a couple of hickies on the cutter head from the attack.

The shaft was galled up a bit as well. Some file work restored it to functionality.
Posted by GBLynden | Yesterday @ 08:14 PM | 7,985 Views
This is an HSDJets D400 3D RC Plane Flight Review By RECKEM ROYS RC & GBLynden's RC.

HSDJets D400 3D RC Plane Flight Review By RECKEM ROYS RC & GBLynden's RC (7 min 52 sec)

Posted by gke | Yesterday @ 08:06 PM | 8,006 Views
There are a zillion conversions out there for this type of chuck glider.

This conversion is intended for indoor flying and is based on a glider costing around $2 to $3 plus the various 1S components. I bought four gliders but they arrived badly bent. - you can see how I restored them here:

The motor is a cheap 8020 with a DSM2 servo-less brick and three nano servoes from BG in this case. The battery is 1S 205mAH DE and came from Micro Motor Warehouse.

There are control surface outlines in the foam but these are not large enough so I pushed the ailerons out to the start of the wing tip up curve and made the elevator full width and all slightly deeper. The elevator halves are connected by a carbon rod but anything stiff enough will do. The elevator control rod needs to be as light as possible however for the aircraft to balance perfectly with the battery full forward. The hingeing is Blenderm but other tapes will work. The foam in this case is CA compatible. The wing saddle has a bamboo stick locator at the back and is held down at the front by the canopy.

The original glider had a steel ball bearing as ballast and was 43gm. The final electrified version AUW is 55gm - nice .

Photos tell it all....Continue Reading
Posted by old4570 | Yesterday @ 07:46 PM | 8,033 Views
Hobbyzone Sport Cub S 2 (7 min 41 sec)

I set up all the flight surfaces as straight and level as I could .
Battery is a Nanotech 260mAh 1s , it's simply a press fit into the battery bay / slot .
CG did seem to be good .
The S 2 did balloon quite a bit , and to not hang off the prop I needed a fair amount of down elevator .
That really slow flight , the S 2 is hanging off the prop some what .
I came home and made a adjustment to the elevator ( down trim ) . The more power I gave , the more it climbed .

Beginner Mode - Wow , can still turn tight . very smooth and my only complaint is the ballooning .
Intermediate mode - Far more responsive , maybe too much so . Really took me by surprise . For a moment I thought I had entered expert mode .
Expert Mode - Seemed a little lethargic to me .

Really going to have to trim out that ballooning .
Power - yeah , needs more power ! Just , under powered .

As a beginner plane . I can see that . Just needs more power so as to grow with the pilot .

Hmmm , Does it offer anything that the UMX Turbo Timber does not ?
Since I own both , I think the TT is the better choice . The size difference is marginal . Where you can fly is pretty much the same . Price ? Rather close .
If you think the TT is too expensive , then give up a few Beers or cigarettes or both and put that money into the TT .
So after adjusting the elevator , I need a 2nd maiden . Be nice to see what the S 2 can...Continue Reading
Posted by Mad_angler1 | Yesterday @ 06:28 AM | 10,787 Views
Herelink 600mw Mod

In this video I show how to modify Herelink from Cubepilot to get 600mw 28db output in all modes.

Herelink 28db 600mw Mode - How To (8 min 6 sec)

How to Force Herelink Max Output

You Need to ADB into the device first

Adb in the air unit and the gcs unit

The config file is = persist.sys.d2d.tx.pwr.cfg

To Check = adb shell getprop persist.sys.d2d.tx.pwr.cfg

By default it contains

These are for the region config, the max supported by herelink is 28db ~ 600mw,
to set it you would go

adb shell setprop persist.sys.d2d.tx.pwr.cfg 28,28,28,28

This would need to be done on both gcs and air unit for both sides

Posted by benjamin presten | Yesterday @ 06:21 AM | 10,828 Views
Butler Blackhawk: Butler Manufacturing was a manufacturer of prefab steel buildings, including hangars, that was founded in 1901. In 1928, Butler decided to venture into aircraft manufacturing. They founded Butler Aircraft Corp to do just that and the first (and only) product was the Blackhawk biplane.

Heading up the design team for the airplane was Waverly Stearman, brother of Lloyd Stearman who founded Stearman Aircraft. Prior to the foundation of either Stearman or Butler Aircraft, both brothers had worked at Swallow Aircraft. This probably explains the incredible similarity between the Blackhawk and Stearman C3 which were designed at almost the same time. While there’s no actual interchangeable parts between the two airplanes, they are very visually similar.

The Blackhawk was a three seat open biplane like so many of its competitors. Up front was a 220hp Wright J-5 radial. It was constructed using the standard steel tube fuselage and wood wings and had a conventional landing gear. The only really odd feature of the Blackhaw is it’s ailerons. Conventional biplanes with a longer top wing almost always have their ailerons on the top wing. The Blackhawk however, ditched the complex control system necessary to do that and simply put the ailerons on the lower wing.

The Blackhawk never really achieved particular fame as the beginning of the depression wasn’t the best time for an airplane like that, but it did manage a little mild fame. Famous race and aerobatic pilot...Continue Reading
Posted by Tazkiller85 | Yesterday @ 04:16 AM | 11,127 Views
Yep Les Amis,
Prenons soin de nos batteries ! J'ai en test depuis quelques jours le chargeur duo HTRC T400 PRO, donc j'en profite pour vous parler de quelques sujets importants en rapports avec nos lipos. Ce chargeur est très ergonomique et simple à utiliser mais c'est aussi un des plus complets niveau accessoires fournis. Rapide à utiliser grâce à sa fonction mémoire (6 au total) et facile à calibrer pour une charge précise. Puissant et pratique pour un prix très raisonnable, je ne peux que valider cet appareil, presque indispensable dans l'atelier d'un fan de RC... Prenez soin de vous et merci à tous pour votre soutien .

HTRC T400 Pro Duo - Review Test Démo - Conseils et Utilisations ! Résultat Concours Permanent. (24 min 9 sec)

NOTATAZ : 17/20 Puissant et Complet !!!

- HTRC T400 Pro ( coupon BGHONEY2110 ) :
- Capteur de température :
- MUSTOOL multimètre stylo numérique ( coupon BGcf2ab5 ) :
- ToolkitRC M4Q XT30/XT60 :
- Chargeur polyvalent HTRC T240 Duo (meilleur rapport qualité prix):
- Mon transfo 4-24V :
- Mon testeur ISDT (calibrable) :
- Testeur balance complet :
- Testeur Buzzer...Continue Reading
Posted by Risto | Yesterday @ 03:51 AM | 11,301 Views
Here's an index to my blog posts. Click the link to directly open a blog post. The entries are numbered, latest entries have a higher number.

Building & debugging OpenTX
#1: Step-by-step guide to building (custom) OpenTX firmware under Ubuntu Linux
#2: Exploring and debugging OpenTX/EdgeTX with Qt Creator IDE under Ubuntu Linux
#3: Step-by-step guide to building (custom) OpenTX firmware under 64-bit Windows 10
#4: Exploring and debugging OpenTX with Qt Creator IDE under 64-bit Windows 10

Building & debugging EdgeTX
#19: Step-by-step guide to building EdgeTX firmware under Ubuntu Linux
#20: Step-by-step guide to building EdgeTX firmware under 64-bit Windows 10

Native MAVLink & MAVLink telemetry with OpenTX
#5: Native MAVLink telemetry with RadioMaster TX16S (w/o having to use Mav2PT converter)
#6: Modified Yaapu telemetry widget to support OlliW MavSDK/native MAVLink on OpenTX

RadioMaster TX16S modifications
#7: RadioMaster TX16S tray modification
#8: RadioMaster TX16S stick pot dial modification
#9: RadioMaster TX16S DFU button modification
#13 RadioMaster TX16S 6-position switch firmware (written from scratch)
#14: RadioMaster TX16S SPI Flash readout
#15: RadioMaster TX16S breakout board
#16: RadioMaster TX16S mainboard
#17: RadioMaster TX16S schematic diagram
#18: RadioMaster TX16S electronic circuit improvement ideas
#21: RadioMaster TX16S enhanced roller board

DIY electronics
#10: USB2PPM Interface for controlling a remote device from PC

DragonLink related
#5: Native MAVLink telemetry with RadioMaster TX16S (w/o having to use Mav2PT converter)
#11: Disabling all RF emissions of DragonLink V3 WiFi+BT ESP32 module

Futaba related
#12: Futaba TM-10 FASST module / T10CG internal module serial communication
Posted by KB1BBY | Jun 18, 2021 @ 10:03 PM | 11,954 Views
My very minimal lineup of surface vehicles is certainly nothing impressive, by any stretch of the imagination. Just inexpensive vehicles in rather oddball scales. Still, I enjoy taking them out for a run every now and then....Continue Reading
Posted by Mr Tim | Jun 18, 2021 @ 09:48 PM | 11,950 Views
The Sangamon Valley RC flyers will be having our first swap meet with the West Central Illinois Hamfest . 8/7/2021 at Carlinville IL
$5.00 fee to get into both events, please review the flyer and any questions let me know.
Thanks for looking. Mr Tim

WillyNilleis will be there.

CRS models will be there.
The rolling Hobby Shop
Custom R/c plans, Parts,Carbon and Kits
Posted by old4570 | Jun 18, 2021 @ 08:55 PM | 12,023 Views
So lets do this :
Bind is DSMx 11ms - The first attempt failed , so I powered the S2 down and then powered it up and tried to bind a 2nd time - Instant bind the 2nd time .
Rudder / Aileron / and Ch5 all needed to be reversed .
Ch6 was routed to my Trainer Switch - This is the panic recovery function . No need to reverse .
My timer and timer re - set are VIA the two position switch I use for throttle cut . So when I activate throttle cut I also re set the timer . And when I de activate throttle cut I start the timer .

I soldered in a new battery plug / and will be using the Nanotech 1s batteries , the one I reached for is apparently 260mAh .
Flying weight is going to be around 66 grams .
CG with the Nanotech ? Looks like it might be close to the money , wont know till I fly it .
Still need to neutralize all the flight surfaces , which I will do after lunch .

Installed a custom JPG for the model image , and also set up the screen to show the battery voltage of the flight battery .
A nice feature , especially when you dont know how long that battery will last .
Posted by Lesmey | Jun 18, 2021 @ 08:52 PM | 11,999 Views
Received my V1200 a few weeks ago. Really enjoying how accurate and solid she feels. Going to try an Apc 10x10e prop now that I'm comfortable with flying her.
Posted by jmxp69 | Jun 18, 2021 @ 05:06 PM | 12,273 Views
EdgeTX has a standalone tool for flashing firmware (and it looks like other functions tbd) via DFU mode. This video shows how to use the flasher to update a TX16s although the process should be about the same for all supported radios:
EdgeTx Snippet • Flash EdgeTx via DFU Mode with EdgeTx Flasher (3 min 37 sec)

Posted by nagas | Jun 18, 2021 @ 01:44 PM | 12,775 Views
A new flying site for Phoenix Flight Sim.

A grassy field with WW-1 vintage aircraft and observation balloons suitable for aircraft of the period.

In the skys, a Sopwith attacks the Bloody Red baron in his Fokker DR1 who gets it!

A Fokker DVII and Eindecker III are among my favourite aircraft....Continue Reading