Anybody got pricing on the kits.

Originally Posted by Tim Wan

Yes, our RTF's included ESC have a switching mode BEC function.

thumbs up Tim.

hey guy's iv'e got one wish i didn't tho' instructions are almost non-existant and i can't work out what goes where,plus none of the bits fit together properly,the nose wheel mounting is VERY poorly designed,i can't work out how to fit & secure the edf unit plus the overall finish is not very good(scratches & digs all over) any help or advice would be greatly appreciated

cheers
chris

Originally Posted by budzilla

hey guy's iv'e got one wish i didn't tho' instructions are almost non-existant and i can't work out what goes where,plus none of the bits fit together properly,the nose wheel mounting is VERY poorly designed,i can't work out how to fit & secure the edf unit plus the overall finish is not very good(scratches & digs all over) any help or advice would be greatly appreciated

cheers
chris

Dear Chris,

Please refer to the page 4 of this thread where has been posted some updated installation of retract landing gear information photoes. It can assist you to built up the plane. Please be reminded to use four long screws up through to the battery sitting hardwood to make sure the nose gear tightly. Meanwhile, the EDF set installation is needed to cut out some foam just enough let the motor cable able pass through behind the EDF. Then you must use some strong double foam tape to fix the EDF set and make sure the alignment is corrected then screw up the EDF set cover. Hope the above information is clear to you. If you still have question, please feel free to contact me.

Thanks for your purchasing our products and hope you enjoy the flight.

Best regards,
Tim

hey tim
that's the exact info i needed for the retracts & the fan now i can get on with my build
thanx very much

cheers
chris

Hello Tim!
Excellent looking birds you have here!!!
The Panther in the video, was that running on 3s??? Have you done any flight tests on 4s?

Victor

Originally Posted by AceMigKiller

Hello Tim!
Excellent looking birds you have here!!!
The Panther in the video, was that running on 3s??? Have you done any flight tests on 4s?

Victor

The testing flight was powered by 3S in the video. Since the EDF set setting issue which is not recommended to use 4S. A new setting for 4S will be taken the testing within this week then post for sharing with all of you asap.
Thanks.

How long untill these are available to us in the USA, hint , hint EJF. Will there be a reciver ready version and a more add your own stuff version also? I really want a silver and blue one with the het 6904 fan and the JS 1400 on 4S. Can you say wet dreams?

Matt

Originally Posted by NIGHTCTMAN

How long untill these are available to us in the USA, hint , hint EJF. Will there be a reciver ready version and a more add your own stuff version also? I really want a silver and blue one with the het 6904 fan and the JS 1400 on 4S. Can you say wet dreams?

Matt

Dear Matt,

I think Robert will try best to arrange it for all of you in the near future.
Attached is some photoes to share with you first. She will be ready to take off and land to USA shortly.

Tim

All built using Lander alloy 3s fan, pretty impressed to be honest, like the "modular" build for each section then just glue it together. Usual ARTF niggles, but it took all of a day and a half to do. Thrust seems pretty impressive for 3s, 4s version should go really well, using a 3700mAh 22c pack, which balances it nicely with that alloy fan out back. Havn't bothered with flaps....I doubt there will be much point, feels nicely balanced and with that big straight wing, and huge tail......can't see lift being an issue....now just need this wind and rain to go...and I'll let you know how the maiden goes.

Phoenix, are you flying from tarmac or grass, did you beef up the nose wheel, if so can you post some pictures please

Just used the dummy oleo leg covers as advised to beef the leg's up [you have to cut away the seating of the retract], other than that....flying off tarmac.....more concerned about it locking down than the wire bending!

Originally Posted by NIGHTCTMAN

How long untill these are available to us in the USA, hint , hint EJF. Will there be a reciver ready version and a more add your own stuff version also? I really want a silver and blue one with the het 6904 fan and the JS 1400 on 4S. Can you say wet dreams?

Matt

We are close to wrapping up the details with RC Lander on the two Panther schemes and the Rafale M so we can get the web site updated and begin the feeding frenzy.

All the airframes will be available with no electronics allowing people to add there own flavors of equipment. in addition options up to Receiver Ready and RTF will be available for everyone to have some fun.

--RW

Great job Robert - way to give the people what they want.

Attached is F9F-2 Tail Blue version new flying video for sharing with all of you.

http://kr.youtube.com/watch?v=quKoaUPFFsQ

Tim