HobbyKing.com New Products Flash Sale
Reply
Thread Tools
Old Mar 21, 2010, 01:09 AM
Registered User
stinger0518's Avatar
houstonia,mo
Joined Mar 2010
43 Posts
question on DT750

i want to buy this for my easy fly looking for almost vertical flight just want max climb rate run shut off motor and glide. What wind should i do and what prop would you recommend for glider applications thanks
stinger0518 is offline Find More Posts by stinger0518
Reply With Quote
Sign up now
to remove ads between posts
Old Mar 21, 2010, 08:17 PM
5,200 Led Lighted Bike-Bob P.
**neons**'s Avatar
USA, MA, Swansea
Joined Mar 2003
2,841 Posts
Hey welcome Stinger, that is great. I am using one of these motors on my glider to do just that. I never had to rewind it at all. I use a 1500mah 11.1 lipo and I climb to 1000feet in not to many seconds and shut down and glide. I setup a 10X 8 folder and she moves. I float around for 20 minutes with no thermals. See her fly here: http://rides.webshots.com/video/3049...29027590gZeAPP

Props to select here:
http://www.hobbycity.com/hobbycity/s...2&v=&sortlist=

Here is another of many planes I fly with this motor. Unwound too
P-40 Warhawk with 11X7 prop
http://rides.webshots.com/video/3065...29027590SnnYHY
Give it a try.
**Neons** Bob
**neons** is offline Find More Posts by **neons**
Last edited by **neons**; Mar 21, 2010 at 08:32 PM.
Reply With Quote
Old Mar 26, 2010, 01:03 PM
I make bad look so good.
SteveC68's Avatar
League City, Texas
Joined Sep 2006
2,529 Posts
What do you use to clean the remaining "factory applied" epoxy from the stator before you rewind? Would MEK clean it without stripping the enamel off? I can never seem to get the little chunks off near top of each tooth.

Thanks,
Steve
SteveC68 is online now Find More Posts by SteveC68
Reply With Quote
Old Apr 01, 2010, 07:27 AM
Jack
USA, ME, Ellsworth
Joined May 2008
17,000 Posts
I just found these wonderful motors back in stock somewhere finally, it was at R2Hobbies in Hong Kong:

http://www.r2hobbies.com/eng/proddet...=rcps81529_750

I placed a first time order with them, they were polite, quick to reply to an email, and coherent in English.

I still waiting to burn one up so I can try my hand at rewinding.

I use it on my 48", 27 oz., SpaFFFnutz flying wing with a 4S A123 pack. I'm flying a Great Planes 10 x 4.5 slow fly prop on it and getting the results listed and seen below. If anyone is looking for industrial strength slow fly props these props are really the bee's knees:

http://www.electrifly.com/miscproducts/gpmq6610.html

I'm running them on a prop saver at 200 Watts and over using doubled up Thera-Band tubing retainers and haven't lost a prop yet.

Jack
jackerbes is offline Find More Posts by jackerbes
Last edited by jackerbes; Apr 06, 2010 at 06:45 AM.
Reply With Quote
Old Apr 04, 2010, 06:00 PM
Dave North
timocharis's Avatar
USA, CA, San Jose
Joined Apr 2004
5,254 Posts
Earthquake!

Manuel, I hear it was a big one. Is everything okay?


Dave
timocharis is offline Find More Posts by timocharis
Reply With Quote
Old Apr 04, 2010, 06:59 PM
Registered Aircraft Offender
Truglodite's Avatar
Carmichael, CA
Joined Feb 2007
3,521 Posts
Yep, a 6.9! Sure hope he's OK. We're prayin' for ya' man.

Kev
Truglodite is offline Find More Posts by Truglodite
Reply With Quote
Old Apr 05, 2010, 01:12 AM
Registered User
Joined Aug 2007
1,430 Posts
Jack

Quote:
Originally Posted by jackerbes View Post
I just found these wonderful motors back in stock somewhere finally, it was at R2Hobbies in Hong Kong:

http://www.r2hobbies.com/eng/proddet...=rcps81529_750

I placed a first time order with them, they were polite, quite to reply to an email, and coherent in English.

I still waiting to burn one up so I can try my hand at rewinding.

I use it on my 48", 27 oz., SpaFFFnutz flying wing with a 4S A123 pack. I'm flying a Great Planes 10 x 4.5 slow fly prop on it and getting the results listed and seen below. If anyone is looking for industrial strength slow fly props these props are really the bee's knees:

http://www.electrifly.com/miscproducts/gpmq6610.html

I'm running them on a prop saver at 200 Watts and over using doubled up Thera-Band tubing retainers and haven't lost a prop yet.

Jack
Its impossible to burn a DT,,,, Im using a 4SA123 and a 12x6 prop , If I remember that is 18 A

Best motor out
NX-687 is offline Find More Posts by NX-687
Reply With Quote
Old Apr 06, 2010, 12:53 AM
Registered User
manuel v's Avatar
Mexico, BC, Mexicali
Joined Aug 2004
5,270 Posts
Thanks Dave and Kev.
Not problem, We are Fine.
check son work place. empty fortunately.
http://www.youtube.com/watch?v=tJjGlJN9s4A

Being Sunday, we were on the airfield.
at that time was flying my f22. and threw me across the earthquake flying the plane. end dizzy.

in 30 years flying, is just my first flight earthquake.

Manuel V.
manuel v is online now Find More Posts by manuel v
Reply With Quote
Old Apr 06, 2010, 07:57 AM
Registered User
vintage1's Avatar
East Anglia, UK
Joined Sep 2002
29,703 Posts
Phew.

where was the epicentre? Baja?
vintage1 is offline Find More Posts by vintage1
Reply With Quote
Old Apr 06, 2010, 10:06 AM
Registered User
manuel v's Avatar
Mexico, BC, Mexicali
Joined Aug 2004
5,270 Posts
Yes. 57km Norteast of Mexicali Baja California Mexico.

Manuel V.
manuel v is online now Find More Posts by manuel v
Last edited by manuel v; Apr 06, 2010 at 10:30 AM.
Reply With Quote
Old Apr 06, 2010, 04:23 PM
Dave North
timocharis's Avatar
USA, CA, San Jose
Joined Apr 2004
5,254 Posts
Great to hear you're okay. And that's funny! Those planes make me dizzy anyway ...


Dave
timocharis is offline Find More Posts by timocharis
Reply With Quote
Old Apr 06, 2010, 08:30 PM
Registered Aircraft Offender
Truglodite's Avatar
Carmichael, CA
Joined Feb 2007
3,521 Posts
Yikes Manuel, was that your video store? Good to hear you're OK and the store was empty. Sounds like a surreal flying experience btw.

Kev
Truglodite is offline Find More Posts by Truglodite
Reply With Quote
Old Apr 07, 2010, 01:14 AM
Registered User
manuel v's Avatar
Mexico, BC, Mexicali
Joined Aug 2004
5,270 Posts
Quote:
Originally Posted by Truglodite View Post
Yikes Manuel, was that your video store? Good to hear you're OK and the store was empty. Sounds like a surreal flying experience btw.

Kev
Not Kev. is in the ofice were work my sons Alberto And Pedro.

My Video Store is all ok. my airplanes are all Ok.
My House is ok.

Thanks.

Manuel V.
manuel v is online now Find More Posts by manuel v
Reply With Quote
Old Apr 07, 2010, 10:55 AM
Dave North
timocharis's Avatar
USA, CA, San Jose
Joined Apr 2004
5,254 Posts
That's a heck of a mess, but it's cheering to hear your stuff is all okay. The guys making the video seemed to be in good spirits.


Dave
timocharis is offline Find More Posts by timocharis
Reply With Quote
Old Apr 07, 2010, 03:01 PM
Jack
USA, ME, Ellsworth
Joined May 2008
17,000 Posts
Truglodite wrote:

"..Also need to make something something big enough for this monster..."

The SpaFFFnutz is a righteous flier for the DAT-750, mine is using a Great Planes Power Flow 10 x 4.5 slow fly prop.

Those props are the best industrial strength SF props on the market and really do this motor justice. The 11 x 8.5 is not a slow fly prop, the other listed there are.

Jack
jackerbes is offline Find More Posts by jackerbes
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
lrk-torquemax diy brushless outrunner kit Ron van Sommeren Power Systems 2 Dec 22, 2011 07:45 AM
For Sale hexTronik 24gram Brushless Outrunner 1700kv tallflyer Aircraft - Electric - Power Systems (FS/W) 3 Jul 10, 2007 09:49 PM
English lrk-torquemax diy brushless outrunner site & mailing list Ron van Sommeren Electric Plane Talk 0 Sep 29, 2001 05:57 PM
E-fly-in&diy brushless outrunner meeting, Sept. 2nd, Winssen/Nijmegen,the Netherlands Ron van Sommeren Electric Flight Events 1 Aug 02, 2001 05:37 AM
diy brushless outrunner/LRK meet & E-fly-in, Sept. 2nd, Nijmegen, the Netherlands Ron van Sommeren Power Systems 0 Aug 02, 2001 05:32 AM